This patch enables the rtc so that the testcase
tests/drivers/counter/counter_basic_api
can run on this nucleo_f091rc board
also when running sanity check
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The Olimex STM32-h103 is a development board based on the STM32F103RB,
very similar to the stm32_mini, which was used as a reference for the
pinmux configuration.
Signed-off-by: Josep Puigdemont <josep.puigdemont@gmail.com>
Update boards that use to declare ethernet support to enable
matching ethernet node.
Similarly to other devices, use dts API to control ethernet pin
settings.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The Arduino Nano 33 IOT is a a small form factor development board
with USB, Wifi, Bluetooth, a 6 axis IMU, and secure element.
Signed-off-by: Michael Hope <mlhx@google.com>
We enhance the help text of the BOARD_ENABLE_CPUNET Kconfig
option, to stress that if the option is used when building
a Non-Secure Application MCU firmware image, the Secure
image counterpart also needs to perform the required GPIO
allocation.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Building Zephyr with CONFIG_TRUSTED_EXECUTION_SECURE=y implies
building also a Non-Secure image. The Non-Secure image will, in
this case do the remainder of actions to properly configure and
boot the Network MCU. So the (strictly) secure firmware image
does not need to execute the configuration and the booting of
the Network MCU, except for the part that does security
attribution. In the absence of any TrustZone awareness, the
single Application MCU firmware will do all the required
steps to configure and boot the Network MCU.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
For true mmio-sram, arc,iccm, arc,dccm nodes we should not be setting
device_type = "memory". This should be used for true DRAM regions of
memory and not on SoC SRAMs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Rename DT_SRAM_SIZE to DT_DRAM_SIZE since that is more correct
* Remove mmio-sram compatible since that is not correct for DRAM.
* Rename node label from sram0 to dram0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
add netif:eth to supported devices
change ram size to 288 as it the size of
sram0 in h745 SoC
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
bringing model and compatible descriptors
to same style as in case of M7 core
enable UART8 for Cortex-M4 in it's dts
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
KConfig.defconfig: enabled NETWORKING support
pinmux.c: added ethernet pins definition for this board
m7 yaml file becomes netif:eth support enabled
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
Switch nSIM from custom ARC UART to ns16550 model. That will
allow us to use zephyr images built for nSIM on other platforms
like HAPS, QEMU, etc...
This patch do:
* switch nSIM board to ns16550 UART usage
* change nSIM simulator configuration to use ns16550 UART model
* drop checks for CONFIG_UART_NSIM in ARC code
* update nSIM documentation
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Removed HFXO request. It is a qemu target thus HF clock source
should not matter.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add devicetree overlay for connecting an Mikroe ETH click shield to an
NXP LPCXpresso55S69 development board.
The LPCXpresso55S69 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ETH click board definition assumes SPI CS0.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Replaces .conf type configuration with .defconfig.
Makes configuration conditional, it depends on shield definition and
networking.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The parameters for this fuel gauge depend on the hardware design and
the expected battery. These should not be defaulted to a value that
may be inappropriate. Require that they be explicitly provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The current shield version shows different configuration, including
disabling default ethernet and wifi interfaces. To allow easy
connection from standard headers, this add two new shield designations.
The existing boards overlays and defconfig were updated.
The documentation was update to reflect changes. A new supported
variations section helps to understand what shield variation user need
select to build their own system.
This changes requires changes on esp32 offload tests to reflect new
esp_8266 shield designations. Sam4e_xpro was keeped as the only one
with dedicated overlay and both frdm_k64f and disco_l475_iot1 were
moved to use standard arduino r3 header using extra args.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The zephyr,code-parition was set incorrectly to SRAM. Set it to the
slot0 partition, so that enabling BOOTLOADER_MCUBOOT will place the code
at the proper address.
Signed-off-by: David Brown <david.brown@linaro.org>
The partition table in DTS are offsets within the flash device, not
absolute addresses. The flash doesn't start at 0 on the lpc55s6x
(because of the secure execution bit), but the offsets in the partition
table should.
Signed-off-by: David Brown <david.brown@linaro.org>
The DT_INST_* macros for PWM may not exactly point to the hardware
instance (e.g. DT_INST_0 may not point to PWM0). So use the node
labels for a more precise match.
Fixes#26782
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Now that PCIE and PCIE_ENDPOINT are made independent,
remove unnecessary CONFIG_PCIE=y from defconfig
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
The Itsybitsy exposes the SWD pins on an unpopulated header on the end
of the board. Add a OpenOCD config and document how to use it.
Signed-off-by: Michael Hope <mlhx@google.com>
The Atmel RF2xx module shield is a generic solution to enable any Atmel
AT86RF2xx IEEE 802.15.4 transceiver. This module enables IEEE 802.15.4
RF2xx Zephyr driver.
The Atmel RF2xx module shield enables any board with an Atmel Xplained,
Xplained-Pro, Arduino or MikroBus expansion header to connect to
networks operation with IEEE 802.15.4, OpenThread or any other stack
based on this media type.
The Atmel RF2xx module is configured to allow interoperate with other
medias like Ethernet. User need configure network stack properlly.
Fixes#26259.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add arduino uno r3 connectors definitions. This enable hardware related
GPIOs and drivers to drive external shields.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add xplained-pro connectors definitions. This enable hardware related
GPIOs and drivers to drive external shields.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add xplained-pro connectors definitions. This enable hardware related
GPIOs and drivers to drive external shields.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add xplained-pro connectors definitions. This enable hardware related
GPIOs and drivers to drive external shields.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add xplained connectors definitions. This enable hardware related
GPIOs and drivers to drive external shields.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
nucleo_f767zi with soc cut-A (Device marking A) has some ethernet
restrictions.
Use of cut-Z is adviced.
fixes#26519
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The board has a SPI NOR flash enabled by default but was missing
the "zephyr,flash-controller" in DTS. This prevents the flash
shell sample to compile. So add the DTS entry.
Fixes#26764
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The `TEXT_SECTION_OFFSET` symbol is used to specify the offset between
the beginning of the ROM area and the address of the first ROM section.
This commit renames `TEXT_SECTION_OFFSET` to `ROM_START_OFFSET` because
the first ROM section is not always the `.text` section.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Cleans up the lpcxpresso55s16 board.cmake to make it consistent with
other lpc boards. jlink.board.cmake sets the default runner to jlink if
not already set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Cleans up the frdm_k82f board document to make its usage of
zephyr-app-commands consistent with other frdm boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The OPENSDA_FW and LPCLINK_FW cmake variables are remnants of pre-west
days where we used an environment variable to set the desired debug host
tool, such as jlink or pyocd, based on which debug probe firmware was
loaded on the board. We now have two possible ways to do this, neither
of which requires the nxp-specific OPENSDA_FW or LPCLINK_FW variables:
1. Set standardized cmake runner variables when generating the build
system:
$ west build -- -DBOARD_FLASH_RUNNER=jlink -DBOARD_DEBUG_RUNNER=jlink
2. Use the west "--runner" argument with the debug and flash commands:
$ west debug -r jlink
Remove the now unnecessary OPENSDA_FW ond LPCLINK_FW variables and
update board documentation accordingly.
A few boards (frdm_kw41z, hexiwear_k64, mimxrt10{20,50,60,64}_evk)
reordered pyocd.board.cmake and jlink.board.cmake includes to preserve
the default runner when OPENSDA_FW was not explicitly set.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The on-board sensor has a enable pin that must be pulled
high in order to power the sensor.
Since no i2c sensor connected to ENV_I2C is supported by zephyr yet,
changed the pins of i2c1 to be connected to CCS811_I2C pins.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Michael Hope
