Convert the hci_spi sample to get the SPI and GPIO settings from Device
Tree instead of Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the HCI SPI driver to get the SPI and GPIO settings from Device
Tree instead of Kconfig. The "zephyr,bt-hci-spi" binding is used as
a common one for this purpose ("st,spbtle-rf" is removed), to take
advantage of the new DT_<COMPAT>_<INSTANCE> generated macros and get
rid of related fixups and aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Now that all supported xtensa boards use DTS we can move the Kconfig
setting to the arch level. Remove HAS_DTS from board Kconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The dts files on these boards had some CONFIG_ defines related to which
memory should be used to hold code. We move this choice out of DTS and
back into Kconfig.
As such, we removed the default setting of 'zephyr,flash' and just
map
CONFIG_CODE_ITCM to:
DT_NXP_IMX_RT_ITCM_0_SIZE
DT_NXP_IMX_RT_ITCM_0_BASE_ADDRESS
CONFIG_CODE_{QSPI,HYPERFLASH} to:
DT_NXP_IMX_FLEXSPI_402A8000_SIZE_1
DT_NXP_IMX_FLEXSPI_402A8000_BASE_ADDDRESS_1
for the mimxrt1050_evk, we remove the default setting of 'zephyr,sram'
and just map:
CONFIG_DATA_DTCM to:
DT_NXP_IMX_DTCM_0_SIZE
DT_NXP_IMX_DTCM_0_BASE_ADDRESS
CONFIG_DATA_SDRAM to:
DT_MMIO_SRAM_80000000_SIZE
DT_MMIO_SRAM_80000000_BASE_ADDRESS
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the how enabling of CONFIG_XIP impacts CONFIG_FLASH_SIZE and
CONFIG_FLASH_BASE_ADDRESS to Kconfig instead of dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit implements a CTF-backend for Zephyr's tracing API.
The CTF-backend itself is split in a middle-layer and a bottom-layer.
- Middle-layer decides the payload in event transactions,
- Bottom-layer implements the IO transport.
A simple POSIX bottom-layer is provided so far.
Signed-off-by: François Delawarde <fnde@oticon.com>
Change compatible, move the JEDEC ID from Kconfig to DTS, convert DTS
size from bytes to bits, remove unreferenced DTS properties. Remove DTS
fixups.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
All Particle mesh devices have an on-board 32 Mibit JEDEC-compatible
flash from GigaDevice. Add bindings to access it.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Previously, only led0 was enabled.
This allows the samples/basic/disco sample to build/run for
this board.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Convert usb_dc_stm32 driver GPIO disconnect to use new defines so we
can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This board is unmaintained and unsupported. It is not known to work and
has lots of conditional code across the tree that makes code
unmaintainable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Since the lp3943 led driver still supports both DTS and non-DTS
configuration, we update the code to use DT_<COMPAT>_<INSTANCE>
defines for the CONFIG_HAS_DTS_I2C case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patchset introduces support for building a board specific custom
image for intel_s1000_crb. This pads the output binary (zephyr.bin)
with some additional data as required by the s1000 BootROM.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
pinmux dev isn't really used or supported. We only have one driver that
is implmeneted, and that driver isn't ever enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ssd1673 display driver to use new defines so we can remove
the dts_fixup.h code for it. Also dropped "-spi" from compatible.
Fix up references in reel_board dts and sample.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add sam0_rtc_driver that implements system timer API on top of the RTC
and can be used as a replacement for the default systick timer.
Signed-off-by: Martin Benda <martin.benda@omsquare.com>
The pins connected to the sensors and microsd card on board
were mapped to SPI_0 and I2C_0, but for nrf52 chips they
cannot both be used together.
Blip is yet unreleased, so change will not affect anyone really.
Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>
Changed 'in place' mode to bypass logger system and directly
call active backends. With this approach memory footprint of
the logger can be significantly reduced in terms of RAM and ROM.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
From the documentation of the SoC and the DevKit it turns out that
there's no hardware PWM controller.
Signed-off-by: Francesco Franchina <cescus92@gmail.com>
Fix the following dtc warnings on S1000:
Warning (simple_bus_reg): /soc/pinmux@81C30: simple-bus unit
address format error, expected "81c30"
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
