Provide through the dts the gpio on which the lsm6dsl INT1 is
connected. Enable also the lsm6dsl trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1020_evk
board for LPI2C1 and LPI2C4. LPI2C1 is shared between the Arduino
connector J18 and the WM8960 codec. LPI2C4 is shared between the Arduino
connector J19 and the FXOS8700CQ sensor (non-populated by default).
Updates the board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables the mcux ethernet driver and pin muxes on the mimxrt1020_evk
board, the same way it is done on the mimxrt1050_evk board. Updates the
board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
mps2_an385 is enabled for networking -> default networking is SLIP ->
SLIP selects UART_PIPE -> UART_PIPE requires UART_PIPE_ON_DEV defined
-> undefined leads to error on building some samples.
Fix all of these issues.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Board can be emulated in QEMU, so select QEMU_TARGET as required for
various bits of "make run" magic to work.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The board has SMSC LAN9220 (actually as an "IP core" in an
FPGA-emulated SoC). The patch includes DTS bindings for this device.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
board.h does not exist for any of the (official) Nordic nRF
boards. This commit corrects the information about the source
ofthe button and LED definitions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Adds an fxos8700 device tree node to the mimxrt1050_evk. The sensor
interrupt gpios require a board modification to be used and conflict
with Ethernet and LCD signals, therefore their pinmuxes are not
configured.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables instance 3 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1060_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Support musca board as a variant, it is a Cortex-M33 based SoC.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update nucleo_l073rz to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
- update yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_l053r8 to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f446re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- disable I2C by default
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f411re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f401re to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- disable I2C and PWM by default
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f302r8 to fit with default configuration guidelines:
- remove reference to arduino_serial as Ardiuno D1/D0 are actually
mapped on PA2/PA3 which are already used for ST_Link com port,
hence not available by default for arduino serial
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f070rb to fit with default configuration guidelines:
-configure arduino spi and i2c
-update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
For normal (over-the-wire) mode of CAN sample lowering bitrate to
125000 to ensure reliable transfer on stm32f072b_disco boards
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
Increase the size of the MCUBoot flash partition in the fstab-debugger
partition table, to accommodate for the RTT console and logs.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
