Previously, only led0 was enabled.
This allows the samples/basic/disco sample to build/run for
this board.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Convert usb_dc_stm32 driver GPIO disconnect to use new defines so we
can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Since the lp3943 led driver still supports both DTS and non-DTS
configuration, we update the code to use DT_<COMPAT>_<INSTANCE>
defines for the CONFIG_HAS_DTS_I2C case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
pinmux dev isn't really used or supported. We only have one driver that
is implmeneted, and that driver isn't ever enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ssd1673 display driver to use new defines so we can remove
the dts_fixup.h code for it. Also dropped "-spi" from compatible.
Fix up references in reel_board dts and sample.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add sam0_rtc_driver that implements system timer API on top of the RTC
and can be used as a replacement for the default systick timer.
Signed-off-by: Martin Benda <martin.benda@omsquare.com>
The pins connected to the sensors and microsd card on board
were mapped to SPI_0 and I2C_0, but for nrf52 chips they
cannot both be used together.
Blip is yet unreleased, so change will not affect anyone really.
Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>
From the documentation of the SoC and the DevKit it turns out that
there's no hardware PWM controller.
Signed-off-by: Francesco Franchina <cescus92@gmail.com>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Add support for nrf52840_pca10090, i.e. the nRF52840 SoC on the
pca10090 development kit. The SoC is tasked to route some of the
nRF9160 pins to different components on the development kit.
Additionally, it can be used as a Bluetooth HCI device.
The routing options appear under "Board config" in Kconfig.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This commit adds the initial documentation information
for board nrf9160_pca10090.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Kconfig and DTS board definition
files for nrf9160_pca10090ns board. This Zephyr board shall be
used to build Non-Secure Zephyr applications on nrf9160_pca10090
Dev Kit.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Kconfig and DTS files for the
nrf9160_pca10090 board definition. The nrf9160_pca10090 board
shall be used to build Zephyr applications, running in Secure
mode, on nRF9160_PCA10090 Dev Kit.
Additionally, the commit introduces a default Secure and
Non-Secure flash partition configuration for the
nRF9160_PCA10090 board, allowing to use Zephyr for building
both the Secure and Non-Secure firmware images.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
If we are setting the code to be in HyperFlash (CONFIG_CODE_HYPERFLASH)
or QSPI (CONFIG_CODE_QSPI) we should enable
CONFIG_NXP_IMX_RT_BOOT_HEADER.
Update mimxrt1064_evk to use select like other boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support files for mimxrt1064_evk, the development board for
i.MXRT1064 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move to using the generated DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_pin and
DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_CONTROLLER defines and drop the
DT_ESWIFI0_CS_GPIOS_PIN & DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_PIN from
dts_fixup.hl
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
This commit adds the simplest configuration for this Nucleo-144 board
stripped down to the parts that are currently tested.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
