STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for mps2_an385 contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
To enable the Hyperflash you have to physically modify the board and
this disables the QSPI. Since we plan on removing Kconfig from device
trees, its easier to treat the hyperflash as a separate board config
and thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We had SEGGER support enabled by default previously, but the new
Kconfig option CONFIG_USE_SEGGER_RTT needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The lpcxpresso54114_m0 tends to be the secondary core so doesn't
typically have a UART setup for it. We had SEGGER support enabled by
default previously, but the new Kconfig option CONFIG_USE_SEGGER_RTT
needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support for 96Boards STM32 Sensor Mezzanine board. This board
is one of the 96Boards Mezzanine board which can work standalone or on
top of the 96Boards Consumer Edition boards.
Below are some of the key features of this board:
1. STM32F446VE MCU
2. 96Boards high/low-speed connectivity
3. Arduino™ Uno revision 3 and Grove connectivity
4. Integrated MEMS sensors:
1. LSM6DS3H
2. LIS3MDL
3. LPS22HB
4. MP34DT01-M
5. On-board ST-LINK/V2-1 debugger/programmer
More information about this board can be found in the 96Boards product
page: https://www.96boards.org/documentation/mezzanine/stm32/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 0.9.5 SDK has support for the Cypress PSoC6 family. Add ablilty to
flash with openocd. I've only tested flashing hello_world on the m0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To enable the QSPI you have to physically modify the board and this
disables the hyperflash. Since we plan on removing Kconfig from device
trees, its easier to treat the QSPI flash as a seperate board config and
thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Zephyr SDK 0.9.4 added OpenOCD support for SiLabs EFR32FG1P SoC. This
commit updates 'Flashing' paragraph of the board documentation to
reflect this change.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Connectors imaages for nucleo_f413zh were actually a reuse of
similar board nucleo_f412zg.
Add dedicated images for nucleo_f413zh.
Fixes#5198
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This patch enables the UART_INTERRUPT_DRIVEN by default for
colibri_imx7d_m4, udoo_neo_full_m4 and warp7_m4 boards.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
The nRF51822 and nRF52832 does not support 802.15.4, so remove this
statement from documentation.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Modify board stm32_min_dev aka "blue pill" led pin assignment in dts
from PB12 to PC13.
This board has a user led connected to PC13.
Sample blinky and similar would run out-of-box without additional
circuit to readout PB12 level.
Tested blinky on corresponding board.
Signed-off-by: Stephen Yi <stephen.jin.yee@gmail.com>
Including Bluetooth to every project unnecessary increase size of the
project, for example hello world sizes:
Memory region Used Size Region Size %age Used
FLASH: 48492 B 1 MB 4.62%
SRAM: 11236 B 256 KB 4.29%
IDT_LIST: 136 B 2 KB 6.64%
after the patch:
Memory region Used Size Region Size %age Used
FLASH: 13344 B 1 MB 1.27%
SRAM: 4004 B 256 KB 1.53%
IDT_LIST: 72 B 2 KB 3.52%
3+ times difference.
PS: It also crashes when 802.15.4 enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Added description how to build, programm and see console output of
hello_world example on cy8ckit_062_wifi_bt_m0 board.
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
The EFM32 Pearl Gecko Starter Kit contains sensors and
peripherals demonstrating the usage of the EFM32PG MCU
family. This patch adds basic support for this board
and is copied from EFM32WG-STK3800.
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for debugging and flashing the mimxrt1050_evk board via
pyocd. Support for this board has not yet been merged in upstream pyocd,
therefore the default in zephyr is left as jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Enabled Messaging Unit B in Cortex-M4 core of Udoo Neo Full board
so it can use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Not pretty to change the PAD name from 2 to 1 as the correct
is PAD2 but for the SAMD20 the register value is 1.
Fixes: 6d08958ad5 ("drivers: uart_sam0: move sercom pad info to dts")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the
nrf52840_pca10056 board and should be maintained and configured
outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
