Instead of enabling Bluetooth by default on nRF5x boards, only enable
the controller if Bluetooth has been enabled by the applicaiton.
Fixes#5454Fixes#12215
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure RTC on nucleo_f746zg.
It is supported through counter RTC API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable testing of counter (COUNTER_{D}TMR_CMSDK) on mps2_an385 and
enable timers on v2m_beetle (TIMER_{D}TMR_CMSDK).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Dual Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the dual timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the single timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled EPIT (Enhanced Periodic Interrupt Timer) in Cortex-M4 core
of Udoo Neo Full board so the counter API could be used there.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add driver support for kinetis ID device.
The length depends on the SoC.
`SIM_GetUniqueId` was not used because the struct would reorder
the ID and makes the driver more complicated because the length
of the struct depends on the SoC.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Adds device tree bindings and nodes for the rocktech lcd module used on
imx rt boards. The use of port, endpoint, and remote-endpoint properties
follow what is currently done in linux, but they are not yet used in
zephyr because some additional plumbing is needed in the
extract_dts_includes.py script.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Always link firmware built for nrf9160_pca10090ns into the
code-partition defined in DT, regardless.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Introduce BOARD_NRF9160_PCA10090NS to differentiate between
secure and non-secure board variants.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
When selecting BT we need to select BT_CTRL for most bluetooth
samples to work correctly.
Let's fix that in the board files.
Fixes the following error when CONFIG_BT is selected:
zephyr/drivers/bluetooth/hci/h4.c:463:30:
error: ‘CONFIG_BT_UART_ON_DEV_NAME’ undeclared (first use in
this function)
h4_dev = device_get_binding(CONFIG_BT_UART_ON_DEV_NAME);
^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Michael Scott <mike@foundries.io>
Indicate that PWM is supported on several Nordic DK boards so that
the pwm_nrf5_sw and pwm_nrfx drivers are covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Indicate that watchdog is supported on several Nordic DK boards
so that the wdt_nrfx driver is covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Changes the default code location from internal itcm to external qspi or
hyperflash. Changes the default data location from internal dtcm to
external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the default code location from internal itcm to external qspi.
Changes the default data location from internal dtcm to external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new configuration option to mimxrt10{20,60,64}_evk boards to link
data into external sdram. The default remains to link data into internal
data tightly coupled memory (DTCM).
Note that mimxrt1050_evk is not included because it already has support
for linking data into sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Unlinke nucleo or disco boards, ST-Link Tx/Rx pins used for Virtual
Com Port is not connected to the chip.
Then, console is not available by default and one should use a serial
cable to enjoy console. Adding mention of this fact to the board
documentation and replacing default hello_world example by blinky,
since blinky sample works without any additional hardware.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The disco_l475_iot1 board should be using CONFIG_USB_DC_STM32 as the
Kconfig sybmol.
Also fix a minor typo in a comment in nucleo_f207zg with regards to
CONFIG_USB_DC_STM32
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
From the driver point of view, monochrome controllers from the ssd16xx
family mostly differ by the amount of row and columns that are
supported. If they support more than 256 rows and/or columns the
corresponding size or position is sent using 2 bytes instead of 1 byte.
This patch therefore adds the width-bits and height-bits DT properties
to make this configurable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that stm32 watchdog should be configured by device tree,
update dts file of boards declaring watchdog support.
Additionally update doc and yaml files.
Add support on some boards that were used to validate the driver
update:
- disco_l475_iot1
- nucleo_f207zg
- nucleo_f429zi
- nucleo_f746zg
- nucleo_f073rz
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the hci_spi sample to get the SPI and GPIO settings from Device
Tree instead of Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the HCI SPI driver to get the SPI and GPIO settings from Device
Tree instead of Kconfig. The "zephyr,bt-hci-spi" binding is used as
a common one for this purpose ("st,spbtle-rf" is removed), to take
advantage of the new DT_<COMPAT>_<INSTANCE> generated macros and get
rid of related fixups and aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The dts files on these boards had some CONFIG_ defines related to which
memory should be used to hold code. We move this choice out of DTS and
back into Kconfig.
As such, we removed the default setting of 'zephyr,flash' and just
map
CONFIG_CODE_ITCM to:
DT_NXP_IMX_RT_ITCM_0_SIZE
DT_NXP_IMX_RT_ITCM_0_BASE_ADDRESS
CONFIG_CODE_{QSPI,HYPERFLASH} to:
DT_NXP_IMX_FLEXSPI_402A8000_SIZE_1
DT_NXP_IMX_FLEXSPI_402A8000_BASE_ADDDRESS_1
for the mimxrt1050_evk, we remove the default setting of 'zephyr,sram'
and just map:
CONFIG_DATA_DTCM to:
DT_NXP_IMX_DTCM_0_SIZE
DT_NXP_IMX_DTCM_0_BASE_ADDRESS
CONFIG_DATA_SDRAM to:
DT_MMIO_SRAM_80000000_SIZE
DT_MMIO_SRAM_80000000_BASE_ADDRESS
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the how enabling of CONFIG_XIP impacts CONFIG_FLASH_SIZE and
CONFIG_FLASH_BASE_ADDRESS to Kconfig instead of dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
All Particle mesh devices have an on-board 32 Mibit JEDEC-compatible
flash from GigaDevice. Add bindings to access it.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
