Reduce unnecessarily large images of boards (> 1MB)
Also fixed typo in doc title for mec2016evb_assy6797
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The creation of the udev rule requires the user to be root else
it will fail. Update the text of the documentation to make it clearer
and change the shell prompt of the command to '#'
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
On nrf52810_pca10040 board, the nRF52810 SoC is emulated on nRF52832.
This patch overrides for this board the number of cycles consumed by
one iteration of the internal loop in `nrfx_coredep_delay_us()` (used
by `k_busy_wait()`), so that the value adequate for nRF52832 is used.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In the recent MDK brought by nrfx 1.6.2, these legacy peripherals have
been revealed as available also in nRF52810. This patch allows their
use in Zephyr drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The i.MX RT1064 evk has one ethernet (10/100M) connector via KSZ8081RNB
phy. Enable related dts nodes and config flags
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This commit adds a patch in the Kconfig.defconfig file of
nRF9160_pca10090 board, that instructs the linker to restrict
the Secure image to the size of its code partition, if the
image is to be combined with a Non-Secure image. Secure images
without accompanying Non-Secure firmware (i.e. with symbol
TRUSTED_EXECUTION_SECURE not set) can use the entire flash.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We do not need to overwrite the reg property of flash0
in nrf9160_pca10090 default partitioning. The property
reflects the flash resources of the SOC, and is passed
in the .dtsi file of nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Most of the other nRF52832 boards have the following settings for
scratch and storage partitions:
scratch_partition: partition@70000 {
label = "image-scratch";
reg = <0x00070000 0xa000>;
};
storage_partition: partition@7a000 {
label = "storage";
reg = <0x0007a000 0x00006000>;
};
Let's adjust the scratch size to align with the others and add the
storage partition so that settings and FS samples will work.
Signed-off-by: Michael Scott <mike@foundries.io>
The MPU should have been enabled on all these boards since they have
Cortex-M7 and need mpu for caching support.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most of the other nRF52832 boards have the following settings for
scratch and storage partitions:
scratch_partition: partition@70000 {
label = "image-scratch";
reg = <0x00070000 0xa000>;
};
storage_partition: partition@7a000 {
label = "storage";
reg = <0x0007a000 0x00006000>;
};
Let's remove the snowflake settings in BLENano2 which coincidentally
are incorrect: storage overruns the flash area by 0x1000 and causes
a crash when enabling FCB storage.
Signed-off-by: Michael Scott <mike@foundries.io>
Remove most unnecessary instances of `export` and `cmake` use that can
instead be replaced with `zephyr-app-commands` or similar. This is to
avoid documentation using different mechanisms to describe the same
actions and in preparation for documenting `west build` everywhere.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The mimxrt1060_evk was missing hwinfo in the supported list. All other
imx rt boards already have it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes Segger RTT on the hexiwear_kw40z and usb_kw24d512 boards by
setting CONFIG_RTT_CONSOLE=y and CONFIG_USE_SEGGER_RTT=y.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Comment for storage partition could be misleading.
Clarify this is a partition used for file system.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Refactor the imx rt code/data location config defaults such that we
default to on-chip memories at the soc level and override to external
memories at the board level. This means that we frequently override soc
defaults for evk boards, but it removes the assumption that all imx rt
boards (particularly non-evk boards) will have the same external
memories as evk boards.
The end result is that imx rt evk boards still have the same defaults as
before, but the way we get there is different.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable pull-up on UART RX pin to reduce power consumption.
If the board is powered by battery and the debugger is
not connected via USB to the host, the SoC consumes up
to 2mA more than expected.
The consumption increases because RX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This is a follow-up to commit e2b38e02bf.
Default PWM instances are enabled in Kconfig and DTS (with channel 0
set to LED0 pin) for these boards so that it is possible to build basic
samples blink_led and fade_led for them without extra modifications.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Following introduction of zephyr sdk0.10 and openocd branch
from from 20190130, stm32l4+ SoC support is now available and
flash and debug operations are available on nucleo_l4r5zi board.
Fixes 12094
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The imx rt family of socs has several options for linking code and data
into internal or external memories, and up until now we have handled
these options at the board level. This has resulted in several Kconfig
symbols being defined in multiple places and triggering warnings in
documentation builds:
warning: the default selection CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) of <choice> (defined at boards/arm/mimxrt1050_evk/Kconfig:9) is not contained in the choice
warning: the choice symbol CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) is defined with a prompt outside the choice
warning: the choice symbol CODE_HYPERFLASH (defined at boards/arm/mimxrt1050_evk/Kconfig:16, boards/arm/mimxrt1060_evk/Kconfig:16) is defined with a prompt outside the choice
warning: the choice symbol CODE_QSPI (defined at boards/arm/mimxrt1050_evk/Kconfig:19, boards/arm/mimxrt1060_evk/Kconfig:19) is defined with a prompt outside the choice
warning: the choice symbol CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) is defined with a prompt outside the choice
warning: the choice symbol CODE_HYPERFLASH (defined at boards/arm/mimxrt1050_evk/Kconfig:16, boards/arm/mimxrt1060_evk/Kconfig:16) is defined with a prompt outside the choice
warning: the choice symbol CODE_QSPI (defined at boards/arm/mimxrt1050_evk/Kconfig:19, boards/arm/mimxrt1060_evk/Kconfig:19) is defined with a prompt outside the choice
The number of warnings increased as we added more imx rt boards. Fix the
warnings by moving code and data location configs from the board level
to the soc level.
The default memories for all imx rt boards are unchanged. The
mimxrt10{20,50,60}_evk boards still default to hyperflash/qspi for code
and sdram for data. The mimxrt1064_evk board still defaults to ITCM for
code and DTCM for data because jlink does not yet support programming
internal flash.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add nvs support to nucleo_f091rc board. This requires to
add erase-block-size property to stm32f0.dtsi.
Storage partition is set to 4kb at the end of the flash.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a space in some long doc titles to allow for wrapping in the title
display. Also fixed a table in the mec2016evb board doc.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The phrase "Zephyr applications use the ..." in many boards and
inconsistently. This is just to say what is the board identify is.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This was tested with a the hello world application. UART 0 was used
as console for displaying "Hello World! mec2016evb_assy6797" to the
a serial terminal.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The board pinmux code has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The values for the registers like GDV, SDV and Boarder Waveform
depend on the panel and display controller. Add DT properties
and obtain such values from DT.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Adding a set of BKMs on how to enable and configure UART1
for the nrf52840_pca10056 board. This instructions are likely valid
to most other nrf52840- family of boards.
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
This commit enables the PWM0 device on the Atmel SMART SAM E70 Xplained
Board, by adding the entries to the DTS and configuring the PWM pins
from the EXT1 connector (channel 0, inverted) and EXT2 connector
(channel 2, inverted and non-inverted) with the corresponding peripheral
functions. It also updates the documentation and mark pwm as supported
for the tests.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
