The UART references in dts_fixup.h are actually SoC-specific, not
board-specific, so they are moved. Since this leaves the board fixups
empty, the file is removed.
The SoC fixups are expanded to include the additional two ports that
are present on some revisions of the Apollo Lake.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Several customer configuration (CCFG) settings are useful for
development and deployment. This commit adds support for setting CCFG
values via Kconfig. It follows TI's recommendation of setting CCFG
values and then including the TI provided CCFG. This commit includes
support for enabling the ROM bootloader and additional settings can be
added as needed.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The HiFive1 and HiFive1 Rev B share the same clock initialization
code, so put it in soc/riscv32/riscv-privilege/sifive-freedom.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
The HiFive1 Rev B adds the following features to the
original HiFive1:
- A second UART peripheral 'uart_1'
- A hardware I2C peripheral 'i2c_0'
- Segger J-Link OB
- An ESP32-WROOM attached to the 'spi_1' peripheral bus
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
tests/drivers/i2c/i2c_api wants to have CONFIG_I2C_0_NAME defined.
Add it to dts_fixup.h as was done for Watchdog and & timer.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Define pinmux base addresses from gpio bases. Pinmux
and gpio functionality are located in the same PCR register
for each pin.
Introduce pinmux Kconfig switches for the SOC.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This commit enforces platform-specific initialization
for nRF SoC family. The specific platform initialization
hook is invoked directly after reset and calls the nRFx
SystemInit() function.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
If the QMSI is not configured in (in the west manifest) we get kconfig
whitelisting errors because the type is declared within the module
itself.
Change default to def_bool to set the type.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add option for enabling the Code Cache present on the NXP Kinetis
KE1xF SoC series and enable it by default.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The Apollo Lake devicetree is augmented with its 8 I2C interfaces.
The default number of dynamic IRQ stubs is increased to deal with
these new interfaces having IRQ vector detection at runtime.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This needs to be pushed down to the SoC level, as it's an Apollo Lake
feature, not a feature of the UpSquared. Remove the Apollo Lake
references to the PCI devices because these will not be used when I2C
support is restored.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Allows snippets to be placed in different locations:
- The noinit, rwdata and rodata output sections
- Two different locations for placing custom output sections,
one location for RAM and another for all other sections.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In kernel_arch_init() we initialize the ARM core (interrupt
setup, fault init, etc.) so we can also move z_clearfaults()
in the same function and skip invoking it in the SoC init
functions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Sample walk through:
1. CPU 0 will wake up CPU 1 after initialization
2. CPU 1 will send to CPU 0 an interrupt over MHU0
3. CPU 0 return the same to CPU 1 when received MHU0 interrupt
4. Test done when CPU 1 received MHU0 interrupt
The wake up second core and private core ID are soc specific.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add LiteX with softcore CPU VexRiscV SoC definitions and default
configurations.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
The CONFIG_CLOCK_CONTROL and CONFIG_NRF_RTC_TIMER were
unconditionally selected when enabling any nRF SoC. But since
timers can be disabled in the kernel, depend instead on
CONFIG_SYS_CLOCK_EXISTS, which is only defined when kernel
timer support is included.
Note that ideally we would enable CONFIG_NRF_RTC_TIMER only, and
that would select CONFIG_CLOCK_CONTROL (on which the RTC timer
depends) but there is a circular Kconfig dependency that prevents
us from doing so.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for NXP MCUX LPUART devices with separate IRQ lines for
transmit and receive status interrupts (e.g. the Kinetis KE1xF SoC
series).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds basic support for nrf52811 in the arch SoC, dts
and nrfx folders.
The nRF52811 is a Bluetooth 5.1 Direction Finding SoC with comprehensive
protocol support.
The nRF52811 SoC is capable of the latest features of Bluetooth 5.1,
the most prominent being Direction Finding.
The radio in the nRF52811 SoC has comprehensive protocol capabilities,
including Bluetooth 5.1 Directing Finding, all Bluetooth 5 features,
802.15.4, Thread, Zigbee, ANT and 2.4 GHz proprietary.
It has 4 dBm TX power and has been optimized to offer the best RX
sensitivity of all SoCs in the nRF52 series.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Delete memory-related configs from defconfig and use device tree based
macros in general riscv32 linker script instead of Kconfig ones.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Use values generated from the device tree in RISCV_ROM_BASE,
RISCV_ROM_SIZE, RISCV_RAM_BASE, RISCV_RAM_SIZE macros.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Use values generated from the device tree in RISCV_ROM_BASE,
RISCV_ROM_SIZE, RISCV_RAM_BASE, RISCV_RAM_SIZE macros.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
add usbd1 definition to rt dts file,
set EHCI controller config default value in rt1050 default config file,
add EHCI controller driver MACROs to dts_fixup.h,
initialize EHCI clock in rt soc.c
add HAS_MCUX_USB_EHCI for supported soc in Kconfig.soc
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Hex firmware file is convenient in some scenarios, like
generating signed firmware with `west sign`. So, enable
generating hex file.
Signed-off-by: Jun Li <jun.r.li@intel.com>
Macros and enums are included for supporting pin configuration
settings.
Entries to the dts_fixup were also included in order
to configure port level settings.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The only use of the BOOTLOADER_UNKNOWN config option is on x86, where
it controls whether a multiboot header is embedded in the output.
This patch renames the option to be more descriptive, and makes it
an x86-specific option, rather than a Zephyr top-level option.
This also enables X86_MULTIBOOT by default, since the header only
occupies 12-16 bytes of memory and is (almost always) harmless.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This commit adds driver support for ADC1 on all 8 supported series of
stm32 with resolution and conversion time selection and calibration.
Currently DMA is not supported for all series, and without it, zephyr
won't be able to catch up ADC's end of conversion interrupt, so this
version of the driver supports one channel conversion only. Users want
multi-channel conversion should use multiple sequences in their app
code.
This driver uses LL lib rather than HAL because the current HAL lib for
ADC will call HAL_DMA_* functions rather than using zephyr's common DMA
interface, so that way the driver will break the consistency of the
code.
This driver has been tested on multiple nucleo boards including
NUCLEO_F091RC/F103RB/F207ZG/F302R8/F401RE/F746ZG/L073RZ/L476RG and all
passed the test cases in tests/drivers/adc/adc_api. If the external ADC
line is floating, it may fail the tests since ADC may get 0V and the
test cases think 0 is failing. Connect it to any voltage source between
0-3.3V will help passing the test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
