Building microkernel for ARC causes a compiler error
due to missing declaration of _sys_idle_elapsed_ticks.
Declare this as extern.
Jira: ZEP-397
Change-Id: I83701f693fea0fcb1ae2c30e0c52abe7987de1f1
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
I notice there are some more places in this file
that can be switched to using tabs.
Change-Id: I7dac2b91f932aa6f167b7eaf93e7c8f571a22d41
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The file gpio_dw_registers.h already had the 4-port GPIO
registers defined, yet the gpio_dw.c implementation didn't
support it properly. There are 4 ports here, not 2, and only
PORTA can support interrupts and debounce.
On the em_starterkit board, for example, PORTA
has 3 bits for buttons: A, L and R. The other 3 ports should not
be used with interrupts & debounce.
I've re-worked this file to derive the port number from the
base address given. The lower 6 bits are divided by 12 to
derive the port number. From this, the registers EXT_PORTA,
EXT_PORTB, EXT_PORTC or EXT_PORTD can be read.
Also, for those ports that don't support interrupts,
set irq_num to 0, and that code will be avoided. I've verified
that I can access GPIO now correctly on the EM Starterkit. The
em_starterkit board support will be submitted soon but I'm
staging in this change first.
Change-Id: I98dbe083e03e046b40e07b4b14a99a39a6d0f0be
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Defer Prepare write errors to be sent in Execute write response
Per Bluetooth Spec. The Attribute Value validation is done when an
Execute Write Request is received. Hence, any Invalid Offset or
Invalid Attribute Value Length errors are generated when an
Execute Write Request is received. Fixes test case
TC_GAW_SR_BI_33_C (run with shell).
Fixes: ZEP-218
Change-Id: I3dc4583f519e0da2e1f741c9b532d6a6c1970225
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This fixes GATT Server indications.
conn handle shall be set to the valid handle, not 0xffff.
If conn passed to bt_gatt_indicate is NULL, indication will be sent
to every client subscribed.
Fix related to ZEP-403
Change-Id: Ie36b957fddfbc5485318bba649d15349e9293868
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
Fixed doxygen comments for flash API usage. Clarified the use of
flash_write_protection_set API for write and erase operations.
Jira: ZEP-383
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Change-Id: I6a323915c63a393b7be8f96fe3fcd9616a9b21d1
Print flag for write_evt() to distinguish between write and
prepare_write. Add offset printing when reading.
Change-Id: I8b53d8f49657ade39b190ab33e99097bb172077c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fix a compile error when trying to set I2C address of LSM9DS0 Gyro to
VCC (0x6B) caused by a typo.
Change-Id: I27850ecd70e715a10b96572aedea0d237dd55cd5
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
I noticed that even though I was building w/o ADC, that some
ADC config symbols were still defined. Adding some "depends on"
to clean that up.
Change-Id: Ie73d131ba1ad63b5f3d920e17b4c7b5a0d785609
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Provide functions of saving and restoring LOAPIC
states to support deep sleep.
Jira: ZEP-223
Change-Id: I1fb427989b021ec8e3a4f6dd0f4766a214360621
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Save and restore IOAPIC flags and irq to vector translation
info for supporting deep sleep.
Jira: ZEP-223
Change-Id: Ifc50a5a72699ff6782ad194d8e96b18fac34da18
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
In scenarios where device PM is enabled and dynamic irqs are
used, move the irq to vector table to RAM and keep it updated,
so that we can use this to restore IOAPIC/LOAPIC vector entries.
Jira: ZEP-224
Change-Id: I0d4350d4e30f8ca337a2a1d4f012748c3cb450f4
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
This is external source code maintained somewhere else. Put it
under ext/ for clarity and maintainability.
Change-Id: I9e7c9d0948a2ba893006e316dc21d9b1a9edfa93
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add I2C QMSI shim driver for sensor system based on QMSI 1.1
Origin: Original
Change-Id: I9c8efe49e8e9b7a5f8496fa49beb68e409148be7
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add QMSI 1.1 based GPIO sub-driver for sensor system.
Origin: Original
Change-Id: Ida5565a5911eb55651a11a4ac0b240c624f8e1ca
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add SPI sub-driver for sensor system.
Use SPI irq number definitions already in Zephyr header file.
Origin: Original
Change-Id: I215db3acc535093dd75c0817cbe5af77e6e76e16
Signed-off-by: Baohong Liu baohong.liu@intel.com
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Attributes should have stored their own attribute handle after
registering service. Handle values are assigned to attributes after
registering service and stack has to copy them.
Fixes:
GATT TC_GAD_SR_BV_03_C PASS
Change-Id: I8463340960d663161d0f7990390e60f06a1c7259
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
This enable checking for errors and automatically print help string:
btshell> connect
connect <address: XX:XX:XX:XX:XX:XX> <address type: (public)>
Change-Id: Ie097ecddb72ab15bf6192e310d0bd839bfd251d5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the CONFIG_SENSOR_DEBUG as it is no longer needed since switching
to SYS_LOG_* in the sensor susbsystem.
Also, use __ASSERT where CONFIG_SENSOR_DEBUG was used to validate
function parameters.
Change-Id: I80ed7209abfb92220fa229d246c5b3a43b887e32
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
I've found many problems with the SPI driver and this repairs many of them.
The baud rate divisor was being derived from the CPU clock. But, some
targets may have a seperate clock attached to SPI. If the soc.h file
defines the symbol SPI_DW_SPI_CLOCK, it will use this instead
of CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC for the baud rate calculation.
completed() had a mistake where it would terminate the SPI transaction
too early, well before the tx data has cleared the FIFO. I found I couldn't
drive an OLED display correctly because completed() was wrong.
The repair is to now consider a new flag called spi->last_tx,
which will be set after the TX interrupt occurs with nothing to send any
longer. There is also a while loop added to SPIN until BUSY drops.
Another improvement is that push_data will NOT consider RX fifo size
if there is no RX going on. The calculation here when RX is going on
could go negative. I've added a check for that and prevent TX handling
if RX buffer is full. I think that is the intention -- to deal with RX first
if its fifos are more full.
In spi_dw_transceive, if we are only doing spi_write w/o reading,
don't enable RX interrupts at all. The OLED I'm working with failed
to have a pull-up on MISO SPI signal. As a result, a huge number of
garbage RX events arrive, and the interrupt handler finds there is
no rx buffer, so it tosses the data. But this is a waist of realtime.
It seems WRONG to enable RX interrupts if its something your not using,
so software can GATE these spurious events in this way.
With these changes, SPI can be used much more reliably, with FIFOs
that are deeper, and SPI devices that only require TX.
Change-Id: I0fe0745f2381c61c8a19ce086496b422a32a30a5
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
This checks if the command string is either NULL or empty since in these
cases there shouldn't be necessary to do any lookup.
Change-Id: I27e6d5b07ab4000cce93a4d1f7952e3c57672657
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Contrary to strcmp strncmp does not match the entire string only the
initial bytes passed as len thus causing a prefix match not a exact
match logic.
Change-Id: I85f96beb2249223f44c81c4efd6bd01bf2033a2e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware does not filter by UUID so we need to do this ourselves.
Change-Id: I55808836369194fbc5ea7c35db2c72fcda75e4eb
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This adds a optional help string to the command table which is printed
when user enters > help <command>.
Change-Id: Id3a8995bb6c4ff6b009418e31968c0677e6e4921
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When using the Synopsys DesignWare Synchronous Serial Interface (SSI),
the FIFO depth can vary from 2-256, depending upon how this module is built.
For quark_se_ss, it was using a depth of 8. For EM Starterkit, it will be
32. Adding this now as a configurable option. A larger FIFO really helps
reduce SPI interrupts.
Change-Id: Id2bc8470bfc08ab447d38b89c7904cff010c63bd
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Just as rxftlr can be read, a macro is needed so that txftlr can be read.
Symmetry.
Change-Id: Id987f700d89268feca60850f4fdf512f990f3ab6
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
A recent submission caused a build error for DW
CONFIG_SPI_DW_INTERRUPT_SINGLE_LINE because the symbols
CONFIG_SPI_<0,1>_IRQ went missing from Kconfig.
I think these should probably NOT be configurable, because
on an SOC, interrupt lines are hard. So I'm changing
the names back to SPI_DW_PORT_<0,1>_IRQ, with there
definitions originatig in the soc.h file.
Also, on DesignWare ARC EM Starterkit, the SPI interface
has 6 slave selects, but IP itself can handle up to 16.
Why does this start from 1 and not 0? Argh!
DBG_COUNTER_RESULT() should expand to 0 when not used.
Also, don't check version from DesignWare IP because
it can be different for each target.
spi_dw_isr() requires a cast when converting arg to dev.
Change-Id: I83d55e0405583e7cafab80b09cbef44e0f96fcb8
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
* Rename BMP280 to BME280 which is a superset for the former.
* Autodetect device based on chip ID.
* Implement humidity fetching and reading for BME280
* Rename sample BMP280 to BME280
Change-Id: I565c769a7011e7496c9f1cad861d5ee311839b4f
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Check if return value is negative when checking for errors, instead of
checking if it's 0.
Change-Id: I0b0af28c02b3760f3128e8cbe48908dabc89af88
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Update all drivers that have vectorial data to return all 3 channels (X,
Y and Z) if the chan parameter is _ANY.
Also fix a compile bug in LSM9DS0 MFD driver.
Change-Id: I5bf261846bcd68c288b96997ff164726f75c151c
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
This is actually a revert from a previous revert. This updates RPC
following the very recent firmware development.
This reverts commit a146f9ef28.
Change-Id: I67b517c3959b5b78a5ef80fbb338d6cc66e43e8e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove the homegrown sensor delayed work API in favor of using the
system-wide workqueue. Drivers still have the option of using their own
fiber.
In a second step, drivers can be refactored to start and use their own
workqueue.
Change-Id: I70dea6fc2abcbc9e04ac1ed3c837483a3d3c4424
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Call bt_conn_security() the same way it is done in upstream code for
NBLE. Currently use BT_SECURITY_MEDIUM as default sec level.
Makes at least following cases pass:
...
1/6 GATT TC_GAR_CL_BI_05_C PASS
2/6 GATT TC_GAR_CL_BI_17_C PASS
3/6 GATT TC_GAR_CL_BI_22_C PASS
4/6 GATT TC_GAR_CL_BI_27_C PASS
5/6 GATT TC_GAR_CL_BI_33_C PASS
6/6 GATT TC_GAW_CL_BI_06_C PASS
...
Change-Id: I2a0c177a187db931e88e2f82a5bda1c0cc04a112
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add driver for the Grove Temperature Sensor which measures ambient
temperature.
Sensor reference page:
http://www.seeedstudio.com/wiki/Grove_-_Temperature_Sensor
Change-Id: I4f56224be5fa7a968749d5d4df8cb99a462c3c21
Origin: original
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
