The driver was using CONFIG_I2S_1_IRQ_PRI which doesn't exist. It
should use CONFIG_I2S_CAVS_1_IRQ_PRI.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The trailing #endif comments used CONFIG_FE310_UART_{0,1} and they
should be CONFIG_UART_FE310_PORT_{0,1}.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implement the new entropy_get_entropy_isr() function to allow the kernel
to collect entropy before the scheduler and kernel data structures are
ready. Switch to an nrf-specific version for high-performance
requirements in the BLE Link Layer.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
CONFIG_UART_NSIM depends on CONFIG_NSIM, which was removed in commit
9bc69a46fa ("boards: Update arc em_starterkit support from 2.2 to
2.3"). Remove the dependency, and also remove the CONFIG_NSIM=y setting
from the test_nsim test (which should now work).
Also change the condition for EXTERN()ing _VectorTable in
include/arch/arc/v2/linker.ld to check CONFIG_UART_NSIM instead of
CONFIG_NSIM. I'm guessing the EXTERN() is there to make the symbol
visible to nSIM, though I don't know anything about it.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The STM32L4x2 SoCs need to control the isolation of the USB features
from VDDUSB. This is done through the PWR_CR2 bit USV, however the
current code checks for the PWR_CR2_PVME1 bit instead, which is only
available on Cat. 3 devices. This bug is also present int the HAL and
likely copied from there.
Replace the check by PWR_CR2_USV instead.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When the RTC support get added we had a select on HAS_RTC, however this
Kconfig symbol didn't exist. Clean this up to match the pattern of
HAS_MCUX_RTC. The driver now depends on that and the SoC selects it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In stm32 clock_control driver, Kconfig symbol CLOCK_STM32_PLL_PREDIV1
in stm32f3 series was set as conditional on the activation of some
specific STM32F3 SoCs that are not supported yet in Zephyr.
Remove this flag.
In order not to loose a rather studious part of code, comment it out
and set a TODO to specify how to re-enable it once it will be
required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There is no pinmux_dw.c and not Kconfig symbols associated with
CONFIG_PINMUX_DW, so remove the references to them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename CONFIG_PMS7003_SERIAL_TIMEOUT to CFG_PMS7003_SERIAL_TIMEOUT as it
was not exposed in Kconfig as a configurable option. So don't use the
CONFIG_ prefix for non-Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In the code we had an if defined based on
CONFIG_BMM150_MAGN_SAMPLING_RATE_RUNTIME that should have been
CONFIG_BMM150_SAMPLING_RATE_RUNTIME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In the code we had an if defined based on
CONFIG_ATAES132A_I2C_SPEED_STANDARD that should be
CONFIG_CRYPTO_ATAES132A_I2C_SPEED_STANDARD.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We had a typo in the Kconfig symbol that was being used to try and set
SYS_LOG_LEVEL. It should be CONFIG_SYS_LOG_NET_LOOPBACK_LEVEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To ensure that early code that requires entropy has the HWRNG devices
fully initialized, initialize them all during PRE_KERNEL_1 stage.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
patch add clock frequency and interrupt property to uart
node in intel_s1000.dtsi. Include soc.h after types.h to
prevent build error.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
This commit adds low level driver support for STM32 micro controllers.
It is tested on stm32f072b in loopback and normal mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Leading/trailing whitespace in prompts requires ugly workarounds in
genrest.py, as e.g. *prompt * is invalid RST. strip() all prompts in
Kconfiglib and get rid of the genrest.py workarounds. Add a warning too.
The Kconfiglib update has some unrelated cleanups and fixes (that won't
affect Zephyr).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Minimal driver for ILI9340 LCD display driver including support
for adafruit 2.2" LCD display (1480)
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Looks lik ARC arch snps_esmk can provide a 3rd port of this controller,
so let's add the necessary bits and pieces to get it instanciated if one
enable this port in DTS.
PCI settings are not introduced for that port as there is no known
arch/board exposing a 3rd port on PCI bus.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi i2c driver and the relevant SoCs accordingly.
Also applying relevant changes on quark_se_c1000_ss as it can use i2c
qmsi driver as well along with qmsi ss i2c driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that all arch using QMSI gpio driver are generating the right
settings through DTS, these options can be removed from Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the ns16550 uart driver and relevant SoCs accordingly.
All generic settings are now DTS based.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi uart driver and relevant SoCs accordingly.
Also: using config for irq everwhere relevantly and not an hardcoded
value in the driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name and irq flags generated through dts as well.
Fix Kconfig for the gpio driver accordingly.
Irq priority is not set by dts for D2000 as it's irq controller does
not support it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In order to check whether an interrupt is pending for the driver user,
the driver itself needs to verify what interrupt paths are enabled (RX
and or TX) so that as not to return true misleadingly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The toplevel adc_seq_table is now copied onto the stack and
the stack copy used.
The contained entries array is now copied onto an allocation
drawn from the caller's resource pool, to prevent modification
of the buffer pointers.
The return value policy here is to oops the caller if bad memory
or objects are passed in, but return an error otherwise.
Based on an original patch by Leandro Pereira, rebased and the
copy of the entries array added.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
The mcux sim clock control driver was originally designed to pass
through the clock subsystem value from dts to the mcux CLOCK_GetFreq()
function. This assumed that the values in
include/dt-bindings/clock/kinetis_sim.h matched the enumeration in
fsl_clock.h, which is true for the coresys, platform, and bus clocks.
However, the low-power oscillator (LPO) clock has a different values in
k64 vs. kw2xd, therefore we must update the clock_control driver to
parse the value from dts and convert it to the fsl_clock.h enumeration.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the configuration, driver, and HAL changes required
to implement a MCUX based RTC driver for the NXP Kinetis KW41Z.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds a prescaler configuration option that denotes the
number of RTC ticks per second. This is used to calculate the value
for 1 second.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch splits off the QMSI RTC into a separate Kconfig
file in preparation for adding more RTC drivers.
Signed-off-by: Andy Gross <agross@kernel.org>
The Kconfig IWDG_STM32_START_AT_BOOT is actually not used and the
watchdog is enabled unconditionnally at init.
Enable the watchdog only if CONFIG_IWDG_STM32_START_AT_BOOT is set.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Add the necessary Kconfigs and supporting code to enable I2C4 which can
be found on certain STM32L4.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
