This is a follow-up to commit 9f56cc5531.
Add net/ in the inclusion of ieee802154_radio.h so that the file can
be successfully included.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The CMSDK uart interrupts for TX and RX can either be treated as a
signel interrupt line or distinct interrupts for TX & RX. In the case
that they were distinct we didn't get the ifdef correct based on DTS.
If we have 2 interrupts in DTS we assume they are for TX & RX and thus
build the interrupt support for distinct TX & RX ISRs.
Also, cleanup handling of UART_2..UART_4 to be similar to how
UART_0/UART_1 code is using DT_INST_IRQN(x).
Fixes#30770Fixes#25601
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A recent patch removed use of the cfg structure, but left a pointer to
it defined which causes build failures.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The NPCX clock driver was already using devicetree, just need to make a
small tweak to use DEVICE_DT_INST_DEFINE and update NPCX_CLK_CTRL_NAME
to match the label for the "nuvoton,npcx-pcc" clock controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a simple pinctrl node for the IOF registers under the GPIO
controller node to be used by the pinmux driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert esp driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop CONFIG_WIFI_ESP_NAME
option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Convert ublox-sara-r4 driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop
CONFIG_MODEM_UBLOX_SARA_R4_NAME option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This include make possible to use the arm_arch_timer on
platform such as Cortex-A9 or Cortex-R7 which has support for
ARM Global Timer.
The global timer is a 64 bit incrementing counter, memory-mapped
in the private memory region.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
In some cases we cannot know the BDF up-front, so provide a way to
look it up based on the vendor and device ID.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These have been redefined in various places - better to have them in a
single place that different users can use.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add ESPI SAF features to the Microchip eSPI driver as
a separate file. ESPI SAF depends upon the core eSPI
driver adding the ability to attach the system SPI
flash to the EC eSPI endpoint instead of the host
eSPI controller.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
During the driver init, the function will set the sensor resolution
based on the driver's dts variable "resolution"
The driver's device tree has been updated to include the value
"resolution".
The default is set to the highest resolution of 0.0625C.
Moved mcp9808_reg_write from mcp9808_trigger.c to mcp9808.c
This allows resue of the same function in both the trigger and
resolution functions.
Function name changed to xxx_16bit to distinquish it from the 8
bit write function that will added.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
In this CL, npcx_miwu_interrupt_configure is no longer responsible for
turning the interrupt off. Although the default state of WK_EN is
disabled, the users still have the chance to configure them when WK_EN
is enabled via npcx_miwu_irq_enable(). Hence, this CL also ensures that
WK_EN is disabled before configuring them.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL uses a simpler configuration approach that turns GPIO's
interrupts off instead of calling npcx_miwu_interrupt_configure
with NPCX_MIWU_MODE_DISABLED.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit introduces runtime query of the HW Capabilities of
the nRF IEEE 802.15.4 Radio Driver.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
Add posibility to configure UART_X device
based on board dts config.
Enable uart clock only if node is enabled
Signed-off-by: Pavlo Hamov <pasha.gamov@gmail.com>
nRF5340 PDK board was deprecated in v2.5.0 release
and is removed now from the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
By the time hostname configuration was implemented, driver was switching
only between STA and STA+AP modes. After dynamic selection between NONE,
STA, AP and STA+AP was implemented (commit referenced below), hostname
configuration no longer takes effect when ESP chip obtains address over
DHCP (and sends hostname in the DHCP request).
Set hostname each time after enabling STA mode, so that it takes effect
in DHCP requests.
Fixes: 03ce61004b ("drivers: wifi: esp: control CWMODE depending on
current needs")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add some simple depends so we limit various I2C drivers to the SoC
families that the drivers are relevant to.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On I2C V1 parts, LL_I2C_EnableIT_TX() translates to EVT and BUF
IRQ enabling.
In stm32_i2c_msg_write function, LL_I2C_EnableIT_TX is called right
after stm32_i2c_enable_transfer_interrupts which already enables BUF
IRQ, which starts the transfer.
As a consequence it could happen that transfer is already complete
at the time LL_I2C_EnableIT_TX is called. This case is not expected
by remaining part of the code which loops forever waiting for BUF IRQ
to be raised.
Remove the superfluous LL_I2C_EnableIT_TX call.
Fixes: #32265
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
nRF52840, nRF52810, nRF52811 and nRF52805 are affected by anomaly 242.
This patch introduces workaround for this anomaly as follow:
Power-fail comparator is disabled before any attempt to erase or write.
Either erase or write is not proceed if EVENT_POFWARN is
already asserted.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Introduce support for situation when synchronization back-end
aborts operation before it is done. synchronization API will
transfer operation return code to the driver shim back.
Additionally:
FLASH_OP_ONGOING value was switched to be positive in order to
not been mislead with a negative error code.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Keep OOB Rx channel and interrupt always enabled.
Send callback when packet is received in OOB Rx channel
if asynchronous host-initiated handling is enabled.
Note that driver doesn't perform any buffering from packets,
so access to OOB Rx channel is gated by client's driver
packet retrieval.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Currently assumption is all OOB traffic over eSPI bus is always client
initiated.
Add option for systems where host can initiate OOB traffic.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The calculated alarm time starts from 2000 but the gmtime_r needs as
input the time from epoch (1970). This causes the alarm time to be
miscalculated due to leap years, as 2000 is a leap year and 1970 is not.
To fix the issue, the 2000 timestamp can be added to the input time of
gmtime_r.
Fixes#32260
Signed-off-by: Antonis Sioutas <antonis.si510@gmail.com>
Fixes: "WARNING:CONSTANT_COMPARISON: Comparisons should place the
constant on the right side of the test"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32 uart driver doesn't support 9bits transactions in any case,
so remove case were it was declared as supported.
Fixes#31799
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit fixes sporadic kernel panics when writing big data chunks
to the flash. (data bus errors)
Reference manual:
If an erase operation in Flash memory also concerns data in the data
or instruction cache, you have to make sure that these data are
rewritten before they are accessed during code execution.
If this cannot be done safely, it is recommended to flush the caches
by setting the DCRST and ICRST bits in the Flash access control
register (FLASH_ACR).
Signed-off-by: Alexander Wachter <alexander.wachter@leica-geosystems.com>
If statement was unconditionally reading a field from async struct
while pointer to this struct may be null if asynchronous API is
enabled but given driver instance is not using it.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Driver uses DEVICE_AND_API_INIT which is deprecated so convert
to using DEVICE_DT_INST_DEFINE instead.
Fixes#32151
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are several different issues when trying to build the icm42605
sensor driver:
* Missing entry in drivers/sensor/CMakeLists.txt
* Issues with #ifndef in header files
* Issues with const usage
* Missing function prototypes in headers
* Fix use of LOG_MODULE_REGISTER v LOG_MODULE_DECLARE
* Add missing dts node to tests/drivers/build_all/spi.dtsi
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update NPCX PWM driver so PWM can be turned off as the first call when
PWM_POLARITY_INVERTED is used.
Signed-off-by: Keith Short <keithshort@google.com>
Disable the DIO1 interrupt when the sx126x modem is in sleep mode.
On nRF hardware, this lets the `GPIOTE` hardware be switched off, saving
15uA.
Fixes#31569.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Update the global state of the modem on calls to `SX126xReset` and
`SX126xWakeup`. This stops `SX126xCheckDeviceReady` sending spurious SPI
commands on every transieve before `SX126xSetOperatingMode` is called.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Drivers are using DEVICE_AND_API_INIT which is deprecated so convert
the iproc_pax dma drivers over to using DEVICE_DT_INST_DEFINE and
DEVICE_DT_INST_GET.
Fixes#32153
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
