It can happen that the command '>' is received between
modem_cmd_send_nolock and modem_cmd_handler_update_cmds. Since the
command handler for '>' is not set, sem_tx_ready will not be given
and _sock_send will timeout. Make sure the command handlers are set
before the send by also passing them to modem_cmd_send_nolock.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Add support for the NXP KE1xF SoC to the eDMA driver. The KE1xF supports
m2m DMA transfers from sources 60 to 63.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
add DTCM caching management in KConfig for stm32h7
add NOCACHE_MEMORY support for stm32h7 M7 CPU series
add HAL_RCC_EX support for stm32h7 series
implemented stm32h7 support within stm32 eth driver
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
added changes that apply to other than stm32h7 series
and prepares stm32h7 series integration:
eth_tx/eth_rx: changed type of total_len
added necessary defines for
tx_desc and own flag extractions
added read_eth_phy_register() function
and corresponding defines
added ETH_DMA_MEM and CACHE defines
following memory buffers declarations moved out of
its ifdef preprocessor macro:
dma_rx_desc_tab, dma_tx_desc_tab,
dma_rx_buffer, dma_tx_buffer
added hal_ret stm32 HAL status checks
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
Added extra asserts to write function of SDL display driver to check if
write is within bounds.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
IPv6 support was not fully implemented in the driver and was disabled.
This commit completes the implementation and enables it when
configured.
Signed-off-by: Vincent Wan <vwan@ti.com>
After switching nSIM to 16550 UART model & driver there is no users
for ARC-NSIM UART. So remove it entirely.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Adapted driver to clock_control changes (usage of onoff manager).
Since timer is permanenty requesting the clock, it is using API
dedicated for that: z_nrf_clock_control_lf_on().
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Updated nrf clock control driver to use onoff service for managing
multiple users.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
FLASH_TYPEERASE_PAGES is null and doesn't represent a bit in the
register, thus this instruction has no effect.
It must be replaced by FLASH_CR_PER which is the bit that should
be cleared.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Added function read_non_aligned that reads data under
non-aligned flash addres to non-aligned read buffer of any size.
Signed-off-by: Mateusz Syc <Mateusz.Syc@nordicsemi.no>
Add support for wsen-itds 3-axis accel sensor, provides acceleration,
temperature data reading and supports configuring of output data rate,
operating mode and scale.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
This gets a little complicated as the driver could be
using PCI-E MMIO, MMIO specified by DTS, or I/O ports.
This driver doesn't use struct uart_device_config any
more.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Good example of the NAMED variants of the MMIO macros, since
an existing inheritance mechanism already took the first-member
slot of the dev_data/config structs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fairly straightforward example of how to deal with PCIe.
The code considers whether a particular instance is PCIe
or not on a per-instance basis, so DEVICE_MMIO_ROM is not
conditionally defined.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A hack was required for the loapic code due to the address
range not being in DTS. A bug was filed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The ethernet driver no longer continues to try to initialize
itself if PCIe probing fails.
This device is always PCIe so we don't need to reserve ROM MMIO
storage.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fix typo in logged Kconfig option name that is missing in used
configuration. This one was mostly problematic for developers wanting to
find such option in source tree using grep - NET_SOCKET_OFFLOAD was not
found in Kconfig files.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
With this refactoring of pcie directory, RC drivers are placed under
host/ directory, EP drivers are placed under endpoint/ directory and
they are completely independent of each other.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
The antenna control GPIO was incorrectly initialized to active. This
is unnecessary since the HAL will activate the antenna switch when the
chip enters an active state.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The new sx1276 pin configuration helpers can be used by the sx126x
driver as well. Move them to sx126xx_common.{c,h} to facilitate reuse.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Fixed AF for USART 6 on PC6/PC7 PG8/PG9/PG12/PG13/PG14/PG15
All RTS/CTS/RX/TX pins now have correct AF7 instead of wrong AF8.
Signed-off-by: Jeremy LOCHE <lochejeremy@gmail.com>
The wdt CLEAR register is a write synchronized register.
To avoid bus stall, check the status of SYNCBUSY before
accessing the register.
Use SYNCBUSY register for SAM E.
If the wdt is syncing, return -EAGAIN to avoid bus stall.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Added a build-time assert to check if heap memory configuration to
make sure that it can accomodate RPMsg queue allocations.
Ref: NCSDK-5479
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
In case of control register lock, driver should return the error
immediately. Otherwise, error is later overwritten by
'rc = flash_stm32_wait_flash_idle(dev);'
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
ep_idx is common used designator for endpoint index,
rename ep_num to ep_idx in usb_dc_sam0 driver.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This commit adds a dependency on the TRNG resource in the TI Power
module, prevents the system policy from entering standby when TRNG is
active, and adds support for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Abort I2C transfers through the MCUX HAL if a transfer fails to avoid
deadlock in the driver/HAL.
Fixes#25098
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Reset gpio is configured during driver initialization. There is no
reason to do it repeat that process later, so replace
gpio_pin_configure() with gpio_pin_set().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Introduce sx1276_configure_pin() helper macro, which hides lots of
boilerplate preprocessor and C code. Doing so allows to uncover
inconsistent gpio initialization flow and prevent such in future. Also
add error log whenever gpio_pin_configure() fails.
It seems like output of gpio_pin_configure() for several
gpios (antenna_enable, rfi_enable, rfo_enable) was assigned to variable,
but its values was never checked. Return value from gpio_pin_configure()
of tcxo_power gpio was even not catched. The only output gpio
configuration that was handled properly was actually reset gpio.
Fix that inconsistent behavior by always checking return value of
sx1276_configure_pin().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fix flash operation timeout due to incorrect use of
secondary ticker to abort any radio in use. Ticker id 0
is reserved for split controller's pipeline preempt timeout.
Using the same ticker id caused the secondary ticker to
not be started if controller is using the same ticker id
for pipeline preempt timeout.
Fixes#26333.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
