Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
API change was done in:
https://github.com/zephyrproject-rtos/zephyr/pull/39041
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
The handler was reworked to internal function and it
is called from the erase and the write
procedures automatically now.
This change was made due to deprecation of the flash write-protection
API.
Explanation for so late removal:
Reworked callback was introduced despite that the API had been
already deprecated at the addition time.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
On nRF53 Series SoCs, the highest SCK frequencies can only be achieved
when the HFCLK192M clock divider is changed from the default /4 setting.
Such change results in increased power consumption, so the divider needs
to be changed only for periods when it is actually necessary.
This commit modifies the driver behavior so that it changes the divider
only when a QSPI bus operation is performed.
However, when XIP accesses to the flash chip are also used, it may be
needed to keep the divider changed even when the driver is idle so that
the XIP access speed is not reduced, hence a custom API function that
allows forcing this is introduced for the driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Only run the `uninit` function if the SPI instance has previously been
configured. This stops an assertion in the HAL drivers from triggering
due to running `uninit` without a previous `init`.
Fixes#42299.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
HAL call function used to retrieve the configured baudrate
returns the real calculated value, which might not be exactly as
the configured. For baudrate of 115200, HAL api
returns 115201, which then causes uart_basic_api test
to fail. Instead of returning the calculated baudrate value,
returns the configured one.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Set enable configuration change bit in can_mcan_set_timing() because
the NBTP register can only be changed if we're in init mode AND
configuration change bit is set, per MCU docs.
Signed-off-by: Jeremy Wood <jeremy@bcdevices.com>
Invalidate the cache before the RX data block is passed to the DMA
engine and not after it is received. If the RX data block contains
dirty cache lines they can be flushed anytime, overwriting legitimate
data that have been prefilled by the DMA module.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
`qdec_sam` driver supports currently only position measurement and does
not support reading of the index signal. Unfortunately, the index
signal was internally enabled in the driver. If the pin to which the
index signal was connected was used by another driver it could lead to
a false detection of the signal change. Detection of the index signal
change resets the position measurement.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fix handling of the return value by `eth_sam_gmac_set_config` function.
The function is used as a backend by
`net_mgmt(NET_REQUEST_ETHERNET_SET_MAC_ADDRESS, ...)` to change the
interface MAC address at run time.
Tested on sam_e70_xplained board.
Fixes#42151
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Remove unneeded NULL check in pmic init function. Not required as
device_is_ready() will handle NULL device structs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Config struct in pmic regulator driver was being used as a non-constant
value when an array defined at compile time was cast to a struct used at
runtime. Move this pointer to the data struct in pmic driver.
Fixes#41951
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This corrects the following:
1. The priority of type cast is lower than member access. So don't need
the redundant parentheses.
2. The macro should be added to the parentheses.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
MCUX usb ISR was making usb callbacks directly, which caused assertion
failures when a callback attempted to lock a mutex. Move USB callback
handler to separate thread, and make ISR notify thread via message
queue.
Fixes#40638
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The CAN_BUS_UNKNOWN CAN controller state is only used to indicate that
the current CAN controller state could not be read.
Remove it and change the signature of the can_get_state() API function
to return an integer indicating success or failure.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The current driver doesn't handle the LBD flag, this leads
uart_stm32_err_check to return always true if a Line Break
is detected.
This PR adds Line Break Detection and the related flag clearing,
F0 series it's excluded from the changes.
Fixes zephyrproject-rtos#41339
Signed-off-by: Andrea Campanella <andrea.campanella@helvar.com>
The commit 44679c7bd8 introduced this
duplicated declaration of the local variable data.
This commit fixes this issue.
Fixes#42117
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The initialization code was updating the freq field in the const
declared config block at runtime because the frequency is not
known at compile time. Add a get_freq() api call to handle any
runtime requests for frequency.
fixes#41953
Signed-off-by: David Leach <david.leach@nxp.com>
Device 'data' variable name was incorrect due to recent treewide naming
cleanups. Fix variable name to fix build error.
Fixes#42118
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Let's have dev_data for dev->data so it will not conflict with struct
call_back data variable.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Coverity identified valid error where the routine does a NULL
check for two different pointers after they have been dereferenced.
fixes#39868fixes#39874
Signed-off-by: David Leach <david.leach@nxp.com>
Current version of STM32 PTP clock reads current PTP time by querying
second and nanosecond registers sequentially. It is possible for second
to roll over between reading second and nanosecond registers, causing
returned time to be off by a second. This bugfix resolves that issue.
Signed-off-by: Alex Sergeev <asergeev@carbonrobotics.com>
Exposes the RC register so that the initial value can be set in
the device tree. This is useful in the case where the timer
generates an event but an interrupt is not required.
e.g generate event to sample adc on RC register match.
Tested on Atmel SMART SAM E70 Xplained Ultra board
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
Current gpio and uart initialization level is set to
PRE_KERNEL_2, which won't let uart_console subsystem
to init its hook properly as it has same level.
Prioritize uart and gpio so that the console hooks
are properly initialized.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Update the Kconfig configuration items used to determine if the current
target is based on the Zynq-7000 SoC family as part of the re-organi-
zation of the Zynq-7000 SoC configuration data.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@Weidmueller.com>
Update the Kconfig configuration items used to determine if the current
target is based on the Zynq-7000 SoC family as part of the re-organi-
zation of the Zynq-7000 SoC configuration data.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@Weidmueller.com>
PR #41918 introduced a few warnings and build failure due to
missing data cofniguration and DEV_CFG() removal.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
After #41918, DEV_CFG removal triggered discard qualifer warning
during build. As uart_hal functions don't required const qualifier
and uart_context_hal_t has modified data, this PR moves hal instace
to data struct instead of config struct.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
After #41918, build started to warn discard qualifer
in config struct. This adds const into those structs.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Updated H4 driver to initialize setup function. Finally bt_h4_vnd_setup
function must be implemented in vendor-specific HCI extension module if
CONFIG_BT_HCI_SETUP is enabled.
BT_HCI_SETUP feature is useful when the BT Controller requires execution
of the vendor-specific commands sequence to initialize the BT Controller
before the BT Host executes a Reset sequence.
To enable this feature the CONFIG_BT_HCI_SETUP should be enable.
Fixes#41140
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
- Added config BT_HCI_SETUP to enable HCI vendor-specific Setup feature,
- Added pointer to 'setup' function in bt_hci_driver structure.
BT_HCI_SETUP feature is useful when the BT Controller requires execution
of the vendor-specific commands sequence to initialize the BT Controller
before the BT Host executes a Reset sequence. To enable this feature the
CONFIG_BT_HCI_SETUP should be enable.
Fixes#41140
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Address the issue mentioned in zephyrproject-rtos#7412
Using printf() with "%x" to print an off_t value produces the
following warning:
format '%x' expects 'unsigned int', argument has type 'long int'
228 | LOG_DBG("Erasing sector at 0x%08x", offset);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~
| |
| off_t {aka long int}
In newlib off_t is long. Even though both int and long are 4 bytes wide
in the architecture in use, GCC wants to see "%lx" to printf() a long.
Using "%"PRIx32 still produces the same warning because PRIx32
(from inttypes.h) still expands to simply an "x" and not "lx".
PR zephyrproject-rtos#40004 has solved this by casting offset to
ssize_t. The same solution is emulated here.
Signed-off-by: Milind Paranjpe <milind@whisper.ai>
Fixed#41945
NO_PINT_INT can have the same value as a specific pin.
E.G. For 1 byte pint_pin_int_t it equaled interrupt1.
Now is instead always 1 higher than the highest pin.
Expects fsl to keep setting values from 0 to
(number of connected outputs - 1)
Signed-off-by: Martin Koehler <koehler@metratec.com>
Build shows warning due to incompatible
CPU vendor name. This fixes it and applies
necessary changes in files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
* New m_can driver variant for STM32H7, as it uses the complete m_can
register set.
* Fix definitions for CAN_MCAN_RXF0S_F0FL, CAN_MCAN_TXEFC_EFSA_POS.
Signed-off-by: Jeremy Wood <jeremy@bcdevices.com>
