Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
In most Nordic SoCs the SPI and TWI peripherals with the same instance
number share certain resources and cannot be used at the same time.
In nRF52810 there are only single instances of these peripherals and
they are arranged in a different way so this limitation does not apply.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Up until now, Zephyr has patched Kconfig to use the last 'default' with
a satisfied condition, instead of the first one. I'm not sure why the
patch was added (it predates Kconfiglib), but I suspect it's related to
Kconfig.defconfig files.
There are at least three problems with the patch:
1. It's inconsistent with how Kconfig works in other projects, which
might confuse newcomers.
2. Due to oversights, earlier 'range' properties are still preferred,
as well as earlier 'default' properties on choices.
In addition to being inconsistent, this makes it impossible to
override 'range' properties and choice 'default' properties if the
base definition of the symbol/choice already has 'range'/'default'
properties.
I've seen errors caused by the inconsistency, and I suspect there
are more.
3. A fork of Kconfiglib that adds the patch needs to be maintained.
Get rid of the patch and go back to standard Kconfig behavior, as
follows:
1. Include the Kconfig.defconfig files first instead of last in
Kconfig.zephyr.
2. Include boards/Kconfig and arch/<arch>/Kconfig first instead of
last in arch/Kconfig.
3. Include arch/<arch>/soc/*/Kconfig first instead of last in
arch/<arch>/Kconfig.
4. Swap a few other 'source's to preserve behavior for some scattered
symbols with multiple definitions.
Swap 'source's in some no-op cases too, where it might match the
intent.
5. Reverse the defaults on symbol definitions that have more than one
default.
Skip defaults that are mutually exclusive, e.g. where each default
has an 'if <some board>' condition. They are already safe.
6. Remove the prefer-later-defaults patch from Kconfiglib.
Testing was done with a Python script that lists all Kconfig
symbols/choices with multiple defaults, along with a whitelist of fixed
symbols. The script also verifies that there are no "unreachable"
defaults hidden by defaults without conditions
As an additional test, zephyr/.config was generated before and after the
change for several samples and checked to be identical (after sorting).
This commit includes some default-related cleanups as well:
- Simplify some symbol definitions, e.g. where a default has 'if FOO'
when the symbol already has 'depends on FOO'.
- Remove some redundant 'default ""' for string symbols. This is the
implicit default.
Piggyback fixes for swapped ranges on BT_L2CAP_RX_MTU and
BT_L2CAP_TX_MTU (caused by confusing inconsistency).
Piggyback some fixes for style nits too, e.g. unindented help texts.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Selecting the type of driver (SPI, SPIM, or SPIS) to be used for
a given SPI instance is mandatory, so the "optional" modifier is
inappropriate for related choice options in the driver's Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the HAS_HW_NRF_* symbols instead of the SOC_SERIES_NRF* ones
to filter out the driver options unavailable on particular SoCs.
Add comments explaining why the SPIM driver is not available for
nRF52832.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The following dependency loop existed:
config SPI_SLAVE
bool
(Defined at drivers/spi/Kconfig:27)
...is selected by...
config SPI_2_NRF_SPIS
bool
select SPI_SLAVE
(Defined at drivers/spi/Kconfig.nrfx:210)
...is in the choice...
choice
bool
depends on SPI_2
(Defined at drivers/spi/Kconfig.nrfx:192)
...that depends on...
config SPI_2
bool
depends on SPI_SLAVE
(Defined at
arch/x86/soc/intel_quark/quark_se/Kconfig.defconfig.series)
...that again depends on SPI_SLAVE
(This might not be a problem in practice, but it'd be difficult to
detect.)
I think the underlying issue is that SPI_2_NRF_SPIS 'select's SPI_SLAVE,
while SPI_2 'depends on' it.
Fix it by having SPI_2_NRF_SPIS 'depend on' SPI_SLAVE as well. This will
require SPI_SLAVE to be explicitly enabled before SPI_2_NRF_SPIS can be
enabled.
No configuration files in Zephyr itself seem to currently enable
SPI_2_NRF_SPIS (and it defaults to n), so no tweaks should be needed
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The OVR condition in the Status Register requires a
particular sequence in order to be cleared. If not
done properly it stays set forever.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This is a rare but valid case when you request the controller to send
dummy bytes on your behalf (it saves memory as you don't need to provide
a valid buffer, just NULL and the numbers of dummy bytes as length).
Without it, user code can get stuck into interrupt loop.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In the current form of the code, the slave frame shifting leaves the TX
full and will shift out some unwanted bytes out on the next transaction.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In SPI slave case the transceive should return either the negative
errno code in case of error or the number of frames received.
So, now:
1. the spi_stm32_get_err() routine already checks whether
the SPI cell got an error and returns -EIO in that case.
2. the transceive() routine always returns whatever the
spi_context_wait_for_completion() has returned, which
is either:
a. -EIO in case of error
b. 0 in spi_master ok case
c. the number of frames received in spi_slave ok case
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
To avoid another thread from modifying the spi_buf_set and spi_config
structures passed to the spi_transceive() syscall, copy those to the
kernel stack before validating.
Fixes#7378.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
According to data sheet of dw_spi, ser reg is used to
select spi device/slave.
one bit in ser maps to one spi device/slave, i.e..
cs 0 ---> bit 0
cs 1 ---> bit 1
cs 2 ---> bit 2
the original code has a bug. the config->slave cannot
directly be written into ser. It should be mapped to
the correct bits through 1 << config->slave.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Refactors the mcux dspi shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. With this change, we are
now getting all soc-specific information from device tree and can remove
the direct dependency on soc.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Spi configs like irq priority and device name should not exist if the
spi driver supports device tree. Fixes a few configs that were missing
the necessary "depends on !HAS_DTS_SPI".
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some spi instance configs were wrapped with ifdefs, while others used
depends. Make them consistent by wrapping them all with ifdefs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The mcux dspi driver was incorrectly using the macro SPI_MODE_GET() to
parse the operation for SPI_TRANSFER_LSB. The effect of this bug was
that the driver would quietly always operate in SPI_TRANSFER_MSB mode.
Coverity-CID: 185401
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This adds a translation layer to make the nrfx driver for the nRF SPIS
(SPI Slave with EasyDMA) peripheral accessible via the Zephyr's API.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Synchronous call return them on success, asynchronous one - with proper
signal - require to get this info through the status.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- removing a left over from previous SPI slave attempt
- unlock async calls on error
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Introduced with the commit 7a9c4cbd9d,
by copy-pasting from "spi_nrfx_spim.c". Shame on me...
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Similar parts of code are aligned in the two shims, so that they
can be easily compared and updated if required.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds a translation layer to make the nrfx driver for the nRF SPIM
(SPI Master with EasyDMA) peripheral accessible via the Zephyr's API.
The shim is provided only for nRF52840 because of a hardware anomaly
present in nRF52832. See Anomaly 58 (SPIM: An additional byte is clocked
out when RXD.MAXCNT = 1) in Errata for this chip.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The simple function that helps to integrate nrfx IRQ handlers with
the IRQ_CONNECT macro can be used in shims for various nrfx drivers,
not only the SPI one.
Similarly, the macro for getting the IRQ number from the peripheral
base address needs to be widely available. It should be even moved
to <nrfx_common.h> in some next nrfx update.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Logical or is unsufficent for setting up new tmod: it's required to
remove previous one first. Indeed, 0 as tmod is valid (tx-rx mode), but
previous tmod could be 10 or 01, so a logical or will keep the previous
tmod leading to a bogus transaction.
Fixing also a rebase issue visible when debug mode is enabled. Slave
callback is a left over from a test on spi slave.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It involves a minor change on which register is configured.
Most of the change is with threshold handling.
Handling the Kconfig based supported mode per-port.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds a translation layer to make the nrfx driver for the legacy
(i.e. without EasyDMA) nRF SPI peripheral accessible via the updated
Zephyr's API of the SPI driver.
Configuration files are already prepared for adding support for SPIM
(Master with EasyDMA) and SPIS (Slave with EasyDMA) peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Now that MCR20A supports the new API, legacy support from mcux dspi
driver can be safely removed.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adds support for the new spi api to the mcux dspi shim driver. Does not
remove support for the legacy spi api since there are still consumers of
that api, particularly the mcr20a 802.15.4 driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
As for RX only, computing the NDF will be used for EEPROM mode.
Only a way to determine EEPROM mode is missing.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
