The original implementation of gpio functions access registers
directly. Using LL library can add a set of unifying access
functions for all series of stm32 for avoiding accessing low level
code, and improve readability.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series STM32 have mostly the same GPIO architecture
and can share the same code for GPIO manipulation.
Functions of the external interrupt line control are also the same.
This patch extracts common code from them and put them into the 'common'
folder.
Functions of control GPIO of these series scattered in
soc/arm/st_stm32/stm32xx/ folders contain these functions:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(), stm32_gpio_set(),
stm32_gpio_get, stm32_gpio_enable_int().
This patch merges them into the gpio_stm32.c file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Connecting to a non-open port causes connect() to hang forever.
This patch releases connect() to return error to the caller.
Signed-off-by: Björn Stenberg <bjorn@haxx.se>
Adds documentation-commentary to some infrastructure used by the LL.
It is a long-term effort to better document the LL.
Notably ticker and mayfly require more documentation; this will be
done later.
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Added macro that generates simple report descriptor for mouse.
This improves the readability of hid-mouse sample.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
It may happen that panic occured while logger backend
was formatting output data. In that case output buffer
could get corrupted as logger assumes that processing
happens in one context only (panic is the only exception).
Added log output buffer flushing on entering panic state.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
* i2c, spi, gpio are not tested, remove them now.
* fix the license issue in openocd.cfg
* fix the shell related setting
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
1. optimize the baudrate calulation
2. For arc iot soc, the interval val is 4
3. before write any regs, the clk of uart must be enabled
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The initial support of iotdk which is a board based on Synopsys
ARC IoT SoC.
In this commit, it includes
* processor support
* UART driver
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The mimxrt1020_evk and mimxrt1060_evk boards had invalid jlink device
names. Debugging via 'ninja debug' now works on these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Commit 76b3518ce6 ("kernel: Make statements evaluate boolean
expressions") changed the type of is_polling in the struct _poller
from int to bool. In the conversion a "0" has been changed into "true"
instead of "false". Fix that.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Adds support for the device configuration data (DCD), which provides a
sequence of commands to the imx rt boot ROM to initialize components
such as an SDRAM.
It is now possible to use the external SDRAM instead of the internal
DTCM on the mimxrt1020_evk, mimxrt1050_evk, and mimxrt1060_evk. Note,
however, that the default board configurations still link data into
internal DTCM, therefore you must use a device tree overlay to override
"zephyr,sram = &sdram0"
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes a Kconfig typo in the mimxrt1060_evk board that was introduced
when the board was split into separate hyperflash and qspi
configurations.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the default TEXT_SECTION_OFFSET from the board level to the soc
level for the imx rt series. This offset is used to reserve space for
the imx boot header for external xip flash images.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the boot data, image vector table, and FlexSPI NOR
config structures used by the imx rt boot ROM to boot an application
from an external xip flash device.
It is now possible to build and flash a bootable zephyr image to the
external xip flash on the mimxrt1020_evk, mimxrt1050_evk, and
mimxrt1060_evk boards via the 'ninja flash' build target and jlink
runner. Note, however, that the default board configurations still link
code into internal ITCM, therefore you must set CONFIG_CODE_HYPERFLASH=y
or CONFIG_CODE_QSPI=y explicitly to override the default. You must also
set CONFIG_NXP_IMX_RT_BOOT_HEADER=y to build the boot header into the
image.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use the page size retrieved via page layout in flash erase
shell command in case erase size is not given.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Driver update to use GPIO driver for the reset control signal.
Driver update to use definitions from DTS including I2C address.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Update Kconfig for tlv320dac audio DAC to include GPIO
as a dependency. The codec driver now uses GPIO driver
to control the RESET for the DAC.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add the codec reset GPIO to intel_s1000_crb's DTS
Update the DTS fixup for intel_s1000_crb accordingly
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add board support files for mimxrt1020_evk, the development board for
i.MXRT1021 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Convert the w25qxxdv driver to use device tree for SPI device params.
Updated the Arduino 101 config to use device tree to specify the SPI
flash. Update the arduino_101_sss to drop Kconfig support for the
w25qxxdv flash.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit configures ETM/TPIU clock upon startup in case SWO logger
backend is enabled on Atmel SAM E70 SoC.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds Serial Wire Output (SWO) logger backend. SWO is an
extension of Serial Wire Debug (SWD) port developed by ARM.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
lpuart1 is the default port used by ST-Link VPC.
Update board description to match out of box board configuration.
Fixes#12092
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In Kconfig.stm32, all UART port symbols were defined with a dependency
on symbol UART_STM32. This is redundant since they are located under
if UART_STM32 condition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On STM32L4, 14 pins (Port G[15:2]), require external power supply.
Activate this at port G init when PWR_CR2_IOSV is defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The IRQ callback function of the USB CDC ACM driver can currently be
called from:
- the USB thread when a bulk in or a bulk out interrupt has been
triggered
- the thread calling cdc_acm_irq_rx_enable or cdc_acm_irq_tx_enable when
enabling the interrupt fires an irq (ie if there is data to read or if
there is no pending data to send)
This causes some issues with at least the shell uart backend, as the
IRQ callback function ends up being called twice concurrently in case a
USB driver sends the requested data almost instantaneously. This is the
case for example of the USB nRF driver which uses DMA. In turn this
cause ring_buf_item_get to be called concurrently, leading to data
corruption:
uart:~$ help
Please press the <Tab> button to see all available commandands.
You can also use the e <Tab> button to prompt or auto-coomplelete all
commands or its subcommands.
You can try toto call commands with <-h> or <--help> parameter for
more informatation.
uart:~$
Fix that by always calling the IRQ callback function through the system
work queue.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
While base64 encoding was enabled settings_val_get_len_cb() returned
encoded length instead of decoded value length.
This patches introduce procedure which calculates the value length
properly. For that additional read of the end of the encoded value is
required for checking how many form last 3 value bytes wear encoded.
fixes#12122
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Zephyr gecko drivers depend on libraries provided by the vendor. The
same libraries may also be used directly by the application code or
RAIL library. To facilitate the latter use case scenario this commit
adds Kconfig options to independently enable compilation of vendor
HAL library modules.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds missing I2C_GECKO Kconfig option which currently is
being set implicitly via .defconfig file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>