Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the value for Low Power Enable (LP_EN) bit mask.
(Issue described by Coverity CID #188734)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm9ds0_gyro driver to get the device name as well as
i2c slave information and gpio info for triggers from device tree.
Updates the build_all test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
nRF 16MHz clock is used by both BLE radio and temperature sensor.
During BLE connection if the temperature sensor is also used then
at some point assert condition is hit in temp_nrf5_sample_fetch().
The error code -EBUSY seen during clock_control_off() is that clock
is no longer needed for the temperature sensor, but it cannot be
just turned off because it is still needed for BLE connection.
Signed-off-by: Dhananjay Gundapu Jayakrishnan <dhananjay.jayakrishnan@proglove.de>
Convert lsm9ds0_mfd accel/magn driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Fixed channel type in get accel/magn channel routines,
where, by mistake, GYRO definitions were used instead of
ACCEL/MAGN ones.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2mdl magnetometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add symbolic names to trigger mode (LIS3DH_TRIGGER_MODE) in order to
be defined in board defconfig files.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis3dh accelerometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
FIX issue #10571 and #10593
atomic_xxx() functions expect the bit argument to be the
position index inside the target integer and not its
numerical representation (e. g. 5 means the 5th bit and not 32).
The original code could potentially override an adiacent variable.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The sensor signal cannot be cleared by the application, so enabling
level triggers causes the system to hang as the callback is invoked
repeatedly. We want notification when the alarm state is entered, and
when it's exited, so use a double edge.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add symbolic names to bus type (LIS2DH_BUS_TYPE) and trigger mode
(LIS2DH_TRIGGER_MODE) in order to be defined in board defconfig
files.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2dh accelerometer driver to get the device name as well
as i2c/spi slave information from device tree. Updates the build_all
test accordingly. (issue #11605)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Remove an unnecessary local variable to store the
return value, instead return directly thereby saving
few bits of memory.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Couple of findings which were revealed after changing
LOG_MODULE_REGISTER macro:
- missing semicolons after LOG_MODULE_REGISTER()
- missing LOG_LEVEL defines
- other
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Provide necessary error handling for `lis2dh_reg_read_byte` function
which might fail.
Also, use a common `status` variable to be used for storing the
error code.
Fixes#10590
Coverity-CID: 188733
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Remove the redundant semicolon used as a terminator in
`if`, `switch`, `while` statements.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
i2c_burst_read can fail during read/write procedure. Therefore,
add a sanity check for its return value.
Fixes#11101
Coverity-CID: 189505
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Driver for LSM303DLHC accelerometer now supports API function
sensor_attr_set for attribute SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Dennis Wildmark <d.wildmark@gmail.com>
Macro is used to create contiguous bitmask between the
arguments passed to the macro.
BITS_PER_LONG is computed as the multiplication of predefined
macros `__CHAR_BIT__` and `__SIZEOF_LONG__`.
Both gcc and clang support these predefined macros.
With this change, replace the redundant defintions of
GENMASK with the new generic macro available.
Fixes#10843
Suggested-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Check the return value of i2c_reg_read_byte() and return
if unable to read the register
Coverity-CID: 188740
Fixes#10585
Signed-off-by: Satya Bhattacharya <satyacube@gmail.com>
Driver fxos8700 can also be used for the MMA8451
accelerometer and offers more functionality.
Revert the commit to avoid duplicate code.
This reverts commit 9c0d7813e5.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add basic verification of the supported devices.
Add IDs for MMA8451, MMA8652, MMA8653 and FXOS8700 and
remove Kconfig FXOS8700_WHOAMI option.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The existing API defined sys_clock_{hw_cycles,ticks}_per_sec as simple
"variables" to be shared, except that they were only real storage in
certain modes (the HPET driver, basically) and everywhere else they
were a build constant.
Properly, these should be an API defined by the timer driver (who
controls those rates) and consumed by the clock subsystem. So give
them function syntax as a stepping stone to get there.
Note that this also removes the deprecated variable
_sys_clock_us_per_tick rather than give it the same treatment.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch changes the behavior of the sensor. The sensor
will remain in sleep mode after initialization and will only
run the measurements once when sample_fetch is called.
This optimizes the power consumption of the sensor as it
stays in sleep mode most of the time.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Refactor and reorganize ALS and proximity setup functions.
Cleanup and reorder register, fix register fields.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The lsm6dsl sensor driver incorrectly conditioned the interrupt pin
Kconfigs upon !HAS_DTS_SPI_PINS, when it should actually be
!HAS_DTS_GPIO_DEVICE.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes casting warnings in multiple sensor drivers when creating their
own thread. These warnings were found when updating the build_all tests
to include missing sensor drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The bmm150 sensor driver was missed in the conversion from kbuild to
cmake. This problem was found when updating the build_all tests to
include missing sensor drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes a compiler format warning in the bmi160 sensor driver. This
warning was found when updating the build_all tests to include missing
sensor drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes unused variable warnings for the adxl362 and lis2dh sensor
drivers. These warnings were found when updating the build_all tests to
include missing sensor drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The sensor driver Kconfigs are sourced inside an "if SENSOR..endif"
conditional, so it is redundant for sensor drivers to explicitly
"depends on SENSOR".
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
For each sensor driver, wrap all Kconfig symbols in a big if/endif
conditional rather than repeating "depends on" for each symbol.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
When config hw cycles=32768 max_wait_cycles maybe small than 60us.
The fix change the condition,make sure the wait time exceeds 80us.
Fixed#9816
Signed-off-by: Frank Li <lgl88911@163.com>
Use Kconfig specific object "named choices".
Aim is to allow to define config choices selection in Kconfig.*
files instead of _defconfig and hence allow to keep flags
activation conditional.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds support for the Analog Devices ADXL372 ultra-low power,
3-axis, +/-200 g MEMS accelerometer. The ADXL372 can be either connected
via a SPI or I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A race condition was identified during the initialization of the
driver when the trigger function is enabled. This exposed two issues:
1 - The fxas21002_handle_int is trying to acquire the semaphore before
it gets initialized. To solve this we need to initialize the
semaphore before calling the fxas21002_trigger_init function.
2 - During the fxas21002_trigger initialization the i2c bus is used
(from fxas21002_handle_int function) at the same time as the
fxas21002_set_power is being called. To fix this we need to
initialize the semaphore with 0 and just release it after calling
the fxas21002_set_power function in the fxas21002_int
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
A race condition was identified during the initialization of the
driver when the trigger function is enabled. This exposed two issues:
1 - The fxos8700_handle_int is trying to acquire the semaphore before
it gets initialized. To solve this we need to initialize the
semaphore before calling the fxos8700_trigger_init function.
2 - During the fxos8700_trigger initialization the i2c bus is used
(from fxos8700_handle_int function) at the same time as the
fxos8700_set_power is being called. To fix this we need to
initialize the semaphore with 0 and just release it after calling
the fxos8700_set_power function in the fxos8700_int
These two scenarios was reproducible in the WaRP7 board with i.MX7 SoC.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Up until now, Zephyr has patched Kconfig to use the last 'default' with
a satisfied condition, instead of the first one. I'm not sure why the
patch was added (it predates Kconfiglib), but I suspect it's related to
Kconfig.defconfig files.
There are at least three problems with the patch:
1. It's inconsistent with how Kconfig works in other projects, which
might confuse newcomers.
2. Due to oversights, earlier 'range' properties are still preferred,
as well as earlier 'default' properties on choices.
In addition to being inconsistent, this makes it impossible to
override 'range' properties and choice 'default' properties if the
base definition of the symbol/choice already has 'range'/'default'
properties.
I've seen errors caused by the inconsistency, and I suspect there
are more.
3. A fork of Kconfiglib that adds the patch needs to be maintained.
Get rid of the patch and go back to standard Kconfig behavior, as
follows:
1. Include the Kconfig.defconfig files first instead of last in
Kconfig.zephyr.
2. Include boards/Kconfig and arch/<arch>/Kconfig first instead of
last in arch/Kconfig.
3. Include arch/<arch>/soc/*/Kconfig first instead of last in
arch/<arch>/Kconfig.
4. Swap a few other 'source's to preserve behavior for some scattered
symbols with multiple definitions.
Swap 'source's in some no-op cases too, where it might match the
intent.
5. Reverse the defaults on symbol definitions that have more than one
default.
Skip defaults that are mutually exclusive, e.g. where each default
has an 'if <some board>' condition. They are already safe.
6. Remove the prefer-later-defaults patch from Kconfiglib.
Testing was done with a Python script that lists all Kconfig
symbols/choices with multiple defaults, along with a whitelist of fixed
symbols. The script also verifies that there are no "unreachable"
defaults hidden by defaults without conditions
As an additional test, zephyr/.config was generated before and after the
change for several samples and checked to be identical (after sorting).
This commit includes some default-related cleanups as well:
- Simplify some symbol definitions, e.g. where a default has 'if FOO'
when the symbol already has 'depends on FOO'.
- Remove some redundant 'default ""' for string symbols. This is the
implicit default.
Piggyback fixes for swapped ranges on BT_L2CAP_RX_MTU and
BT_L2CAP_TX_MTU (caused by confusing inconsistency).
Piggyback some fixes for style nits too, e.g. unindented help texts.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Only basic features supported initially but more could be added from:
https://www.nxp.com/docs/en/data-sheet/MMA8451Q.pdffixes#9006
A sample app will be provided in a separate PR.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
This patch adds support for the Analog Devices ADT7420 High-Accuracy
16-bit Digital I2C Temperature Sensors. Optionally sensor threshold
events are supported.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These cases weren't caught by the heuristic used by the warning added in
commit 6eabea3a7e ("Kconfiglib: Warn for unquoted string defaults"),
because "GPIO_0" has no lowercase characters in it.
Unquoted Kconfig values are are indistinguishable from reference to
(undefined) symbols in general. Quoting all string defaults will help
find "true" references to undefined Kconfig symbols, and makes it
clearer that the value is constant.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
As stated in LIS2DH datasheet in section "5.1.1 I2C Operation",
in order to read/write multiple bytes on I2C it is necessary
to add the autoincrement bit to the subaddress field.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The lis2dh_burst_write used "bus" as an input parameters, while
inside "dev" was referred. Now variable names are aligned.
Signed-off-by: Evgeny Kalugin <evgeny.kalugin@intel.com>
The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Rename CONFIG_PMS7003_SERIAL_TIMEOUT to CFG_PMS7003_SERIAL_TIMEOUT as it
was not exposed in Kconfig as a configurable option. So don't use the
CONFIG_ prefix for non-Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In the code we had an if defined based on
CONFIG_BMM150_MAGN_SAMPLING_RATE_RUNTIME that should have been
CONFIG_BMM150_SAMPLING_RATE_RUNTIME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This patch fixes an overrun detected via Coverity. The
lsm6dsl_odr_to_freq_val function takes an index as argument. If the
index is out of bounds, the expected behavior was to return the last
element of an array. The actual behavior was to overrun the array.
Fixes: #7482
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxos8700 interrupt pins to all boards that
have this sensor. The frdm_k64f and hexiwear_k64 connect both sensor
interrupt pins to the mcu, but the frdm_kw41z connects only one.
The fxos8700 driver is currently only aware of one sensor interrupt pin,
therefore the routing of INT1 or INT2 to the driver is handled in each
board's dts.fixup.
The fxos8700 sample application has been broken since the refactoring of
the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hts221 requires 2.2 ms at boot time to download
the flash content into the volatile mem and the
calibration values cannot be read before that.
This issue is causing following crash:
***** USAGE FAULT *****
Executing thread ID (thread): 0x20000234
Faulting instruction address: 0x80037de
Division by zero
Fatal fault in essential thread! Spinning...
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The XSHUT pin, used to shutdown the device when it is not
in current use, is optional and some boards (like ArgonKey)
leave it tied to vdd. So, the driver must provide a way to
make this part configurable.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In order to be able to change at runtime the Output Data
Rate (ODR) as well as the Full-Scale (FS) for both the
Accelerometr and Gyroscope the driver needs to provide
the .attr_set callback.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In .h there are few typos that are fixed in this commit:
- Delete LSM6DSL_REG_CTRL3_C and LSM6DSL_REG_CTRL9_XL
register sections duplication.
- Fix LSM6DSL_REG_CTRL6_C address.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adding sensorhub support. Only one slave device can be selected
among LIS2MDL (magnetometer) and LPS22HB (pressure and temperature).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The sensor channel type for the nRF TEMP peripheral is incorrectly set
to SENSOR_CHAN_AMBIENT_TEMP. This peripheral measures die temperature,
not ambient temperature.
Fix the sensor channel.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Some device include a temperature sensor, usually used as a
companion for helping in drift compensation, that measure the
die temperature. This temperature IS NOT related to the the
ambient temperature, hence a clean separation between the two
is required.
This commit introduces a clean separation between the two
types of temperature leaving the old deprecated definition
still there.
The list of current drivers that read the die (and not the ambient)
temperature is the following:
- adxl362
- bma280
- bmg160
- bmi160
- fxos8700
- lis3mdl
- lsm6ds0
- lsm6dsl
- lsm9ds0
- mpu6050
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add SPI bus support to LSM6DSL sensor. The bus routines (i.e. I2C
and SPI) are defined in separate files, where proper r/w callbacks
are registered.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The sensor enables the readout of multiple consecutive registers if
the MSb of the sub-address is set. The other 7bit are the register
address.
Signed-off-by: Tobias Aschenbrenner <taschenb@posteo.de>
The existing nrf5_common.h now applies to other Nordic ICs that are not
part of the "5" family. Instead rename this to nrf_common.h to cover the
upcoming ICs that belong to other families.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The arithmetic performed on the CO2 and VOC measurements is pointless as
the units of the sensor already match those of the API, furthermore the
multiplication will overflow the u32_t with CO2 or VOC readings greater
than 4294 ppm or ppb. This CO2 concentration is achievable by breathing
at the sensor.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A condition is added to the Kconfig file to disable config options which
will be supplied from the dts.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
VL53L0X_PerformSingleRangingMeasurement() returns a signed 8-bit
integer, not an unsigned 8-bit integer, making the "< 0" comparison
worthless.
Coverity-CID: 182593
Coverity-CID: 182597
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The I2C address of vl53l0x are write in hex, but the VL53L0X_I2C_ADDR
type is int.
Fix this by replace "int" with "hex".
Signed-off-by: Ding Tao <miyatsu@qq.com>
It makes no sense to set the restart condition flag on a first message
and some i2c bus drivers (like the stm32 v1 driver) actually reject
them by returning an error from i2c_transfer().
This patch fixes that by using i2c_burst_read() in tmp112_reg_read()
instead. For consistency, tmp112_reg_write() is also changed to use
i2c_burst_write().
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
I have been using this the TMP112 driver with success with a TMP102
connected to to nucleo-f411re board (via I2C1 using PB8/9).
According to the datasheets, both devices are both driver and pin
compatible although the TMP102 is less accurate.
This temperature sensor is not a thermopile sensor type as stated in
comments.
This patch updates that help info
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Most of sensor channels defined by Zephyr use the main, unscaled
SI unit. We also have SENSOR_CHAN_ALTITUDE which is defined in
meters. So, it only makes sense to define distance in meters too
The only driver supporting SENSOR_CHAN_DISTANCE as of now is
vl53l0x.c, which was updated accordingly. Also, update doc links
in the driver based on the review comment.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Based on the discussion in #5693, the reason why humidity was defined
in milli-percent was likely following Linux which defines it as such
in its sensor subsystem:
http://elixir.free-electrons.com/linux/latest/source/Documentation/ABI/testing/sysfs-bus-iio#L263
However, Linux defines temperature in milli-degrees either, but
Zephyr uses degrees (similarly for most other quantities). Typical
sensor resolution/precision for humidity is also on the order of 1%.
One of the existing drivers, th02.c, already returned values in
percents, and few apps showed it without conversion and/or units,
leading to confusing output to user like "54500".
So, switching units to percents, and update all the drivers and
sample apps.
For few drivers, there was also optimized conversion arithmetics
to avoid u64_t operations. (There're probably more places to
optimize it, and temperature conversion could use such optimization
too, but that's left for another patch.)
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Move to new Kconfig pattern in which we use an if !HAS_DTS_I2C_DEVICE
block for the Kconfig symbols that can now come from DT generation.
This pattern is useful to allow us to define default values for the
generated symbols for build-all testing.
Fixes: #5877
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to use an if HAS_DTS_I2C_DEVICE instead of depends on so that the
Kconfig sybmols don't even show up if HAS_DTS_I2C_DEVICE is true.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The generic library provided by ST in ext/hal/st/lib/sensor/vl53l0x
needs to be adapted to the platform. In this case, the main
modification is the way to use I2C. This is now using the Zephyr
I2C API.
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Add driver for ST vl53l0x time of flight sensor.
This driver can be used in 2 modes :
* proximity sensor :
configure VL53L0X_PROXIMITY_THRESHOLD
will return 1 if target is between sensor and threshold,
else, 0
* distance sensor :
will return the distance in millimeters from sensor to target
This driver use the official STMicroelectronics library for vl53l0x.
(in ext/hal/st/lib/sensor/vl53l0x)
Signed-off-by: Vincent Veron <vincent.veron@st.com>
This reverts commit 2a7efb7419.
"choice" section in board Kconfig.defconfig introduces a dependency
from the sensor to the board. As a consequence a warning was generated
whenever the sensor was used on another board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This reverts commit 2e20f49167.
"choice" section in board Kconfig.default introduces a dependency
from the sensor to the board. Then a warning was generated
whenever the sensor is used on another board
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the driver for Panasonic AMG88xx
infrared array sensor.
The driver was developed within the framework of a student
internship in the development department. The task of the
student was to implement the trigger part of the driver,
transfer and visualization of the measured data.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
In order to be able to default Kconfig "Trigger mode" choice
in a board Kconfig.defconfig, this commit provides it with a name.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to be able to default Kconfig "Trigger mode" choice
in a board Kconfig.defconfig, this commit provides it with a name.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There are several issues with the dev_config union used as a
convenience when calling the i2c_configure api. One, the union is well
name spaced protected and doesn't convey use with just i2c. Second
there are assumptions of how the bits might get packed by the union
which can't be guaranteed. Since the API takes a u32_t lets change in
tree uses to using the macros to setup a u32_t and make the union as
deprecated.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- place all sensor Kconfig options in submenu
- separate device drivers and common options with a comment line
- align help text
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Indenting preprocessor directives reduces the code readability, because
it make preprocessor directives harder to spot.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch implements BMM150 driver with polling mode and its tested
with original BMM150 sensor hardware. Driver works on I2C
interface as of now.
Following datasheet is taken as reference while developing driver.
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf
Signed-off-by: Punit Vara <punit.vara@intel.com>
This patch implements following functionality in polling mode.
Ambient light
RGB light
proximity sensor
Following datasheet has been used to develop driver
https://docs.broadcom.com/docs/AV02-4191EN
Jira: ZEP-1552
Signed-off-by: Punit Vara <punit.vara@intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Support for LSM6DSL accelerometer and gyroscpe sensor
with bare minimum features.
For more info on this sensor:
http://www.st.com/en/mems-and-sensors/lsm6dsl.html
Change-Id: I9b100a3e030faa8a70a5015a881025c876b81be4
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
i2c_burst_write API implementation in some driver
and generate a sequence of messages that does not allow to
communicate with LIS3MDL sensor. This commit replaces use
of i2c_burst_write with a call to i2c_write, which enables
sensor configuration.
Meanwhile, description of LIS3MDL is completed in sensor
header file.
Change-Id: Ib1b4643365f3c70b31fbfc4b0c30cff294b475a3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Support for LPS22HB Pressure and temperature sensor provided
with bare minimum features.
For more info on this sensor:
http://www.st.com/en/mems-and-sensors/lps22hb.html
Change-Id: I14992b954053094beb054d0dba7581f6e29a3e68
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
* lis2dh 3 axis accelerometer support on SPI and I2C bus
* data ready and anymotion type of trigger support
Tested on Dynastream module D52QD2M4IA-A using SPI
Origin: based on Zephyr lis3dh driver
Change-Id: I2c4e9418b87f09c957bba8f73522bd78830bc809
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix doxygen comment typos used to generate API docs
Change-Id: I6fd5051c99bdcc731740c92001e525349c254d85
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This reverts commit e60af3be66.
We revert this as we intent to move away from {u}int{8,16,32,64}_t types
to our own internal types for sized variables so we shouldn't need the
PRI macros anymore.
Change-Id: I4a57eb2c23cb1b137112224f604602d40c7cce4f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To allow for various libc implementations (like newlib) in which the way
various {u}int{8,16,32}_t types are defined vary between both libc
implementations and across architectures we need to utilize the PRI
defines.
Change-Id: I69e60e3823028389b314adaf6e279fd47fde1182
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
That option was not defined and the sensor does not have this feature,
probably was part of some copy/paste mistake.
Change-Id: Ib24d1f85cf90648b01fa81b285a1ec01fe28c545
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds basic sensor driver support for the Maxim MAX30101 heart rate
sensor.
This driver does not yet support any sensor triggers such as the data
ready trigger, or runtime changing of sensor attributes.
Default configuration values were taken from the MikroE Hexiwear driver.
https://github.com/MikroElektronika/HEXIWEAR
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX30101.pdf
Jira: ZEP-720
Change-Id: Ie8981e124da36a56a214f133bf9a11b9f47d60fa
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes the fxos8700 Kconfig help indentation to be <tab><space><space>.
Change-Id: If6e9395b5d28044962ca568be5515658e7dc2627
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds sensor driver support for the NXP FXAS21002 3-axis gyroscope.
Includes statically configurable range and output data rate, as well as
the sensor data ready trigger.
Datasheet:
http://www.nxp.com/assets/documents/data/en/data-sheets/FXAS21002.pdf
Jira: ZEP-1392
Change-Id: I84587c4d5e76863245e9d045c6abb10b21b2615a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The fxos8700 is primarily an accelerometer/magnetometer, but it does
also include a temperature sensor. Note that the temperature sensor is
uncalibrated and can only be used when the magnetometer is enabled
(magnetometer-only mode or hybrid mode).
Change-Id: I74c4ae68c30e0f9836caa70baed44ad8956b17ea
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Support connection via SPI and keep I2C as the default.
Jira: ZEP-1698
Change-Id: I42a76131577a37429375364deb07e451107f5d81
Signed-off-by: Dario Pennisi <dario@iptronix.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use new device name for SPI device
Jira: ZEP-1704
Change-Id: Iec39468bbef54423af2b3a681dd4ae1eee866d1e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add sensor sample ready check before fetching the sample.
Otherwise, invalid value will be returned.
Jira: ZEP-1532 ZEP-1358
Change-Id: I570151c8ae93fbb744dac857521f596fd63806a6
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
SENSOR_CHAN_*_ANY will be deprecated, so use the new SENSOR_CHAN_*_XYZ
enum values.
Change-Id: I91cf25864613a934feab65588969d10c52fd4fe6
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Fixes fxos8700_gpio_callback() to pass a pin number to
gpio_pin_disable_callback() rather than a pin mask.
Jira: ZEP-1507
Change-Id: I15bfbf4d3377f22942aa549377472d2b1142c32b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The pulse config option requires triggers enabled, so expand the
trigger requirement to also include all the pulse configs.
Change-Id: Ib94f4071cac757b24bfe940ca64fd11b07fed1c1
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
FXOS8700_THREAD_PRIORITY and FXOS8700_THREAD_STACK_SIZE need to also
depend on FXOS8700_TRIGGER, else they will not show in the fxos8700
menu entry when running "make menuconfig".
Change-Id: I8f59125157f046592f3c92dcf2a92bd0e407cd6a
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the type field from the sensor value structure. All values will
have the type previously defined by SENSOR_VALUE_TYPE_INT_PLUS_MICRO.
This simplifies the interface, as apps will know what value type to
expect. Apps that prefer to use double values can optain them using the
sensor_value_to_double function.
Change-Id: I3588d74258030eb16c3f89d8eead13cca4606b18
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The sensor_attr_set() wrapper deals with drivers that do not support
the attribute set API, there is no need to provide a per driver
implementation that only return -ENOTSUP.
Change-Id: I1568ab018988fc560bd89ab96f2f2256ddd5b7e1
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
From code inspection, the driver always took timeouts in milliseconds.
The only sub-ms wait uses k_busy_wait(), which has microseconds
granularity, but its granularity does not depend on the system clock
tick rate.
Change-Id: If48363fd1fbeeb8e5ff0f0f2ca86e671d63bc571
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
It receives a timeout in ms, but was still converting it to ticks, while
the unified kernel API takes a value in ms.
Change-Id: I8ff7f44090716385764fe4b2a087043a2e0d70af
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds optional support for tap and double tap sensor triggers to the
fxos8700 driver using the pulse detection hardware function.
Default configuration values were taken from NXP AN4072, section 6.3.
http://cache.nxp.com/assets/documents/data/en/application-notes/AN4072.pdf
Change-Id: Ia95091628a853eb956f6fd1df099a9e6e101b707
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove the unused argument and comparing int to unsigned int
compiler warnings.
Change-Id: Iad79ec2ef8206b2494875a93551a0f47e234ff8d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Directly use AON GPIO trigger instead of IPM.
In the past, SW did not allow arc to receive AON GPIO interrupt.
So, interrupt from BMI160 was routed to x86 cpu. Then, x86 cpu
passed the event to arc through IPM. But, SW was updated and arc
is able to directly receive interrupt from AON GPIO now. So, IPM
is not needed any more. Let's remove IPM related code and use
GPIO as the default trigger source.
This change is on top of the bmi160 sample app change to not use
IPM.
Change-Id: I49d8040764d03b24e09d89e66643c020ef63a3c9
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Update drivers to return INT_PLUS_MICRO values instead of doubles.
This hides the fact that the drivers use floating point operations and
doesn't force the application to use them as well.
Change-Id: I14c6faecb35331c2fdbdab41bc624d751de984b8
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Use integers for sensor value calculations in which doubles are not
required.
Change-Id: I8662023ca596cb232e31849b0b77ae2bf0372cf0
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Remove SENSOR_VALUE_TYPE_INT as it is the same as
SENSOR_VALUE_TYPE_INT_PLUS_MICRO with val2 set to 0.
Change-Id: If5a9c579b7267701c27f40fd887acae47d64edc5
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
This issue was reported by Coverity
Coverity-CID: 157621
Change-Id: I7f84c0868467ab55e033aecac037967da001a6db
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Basic interrupt driven driver for the nRF5 onboard temperature sensor.
Change-Id: Id0ac303293b8e8b8285b19bcda31284ee6617105
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Adds general sensor triggering support to the fxos8700 driver, including
options for the driver to use its own thread or the global workqueue
thread to handle sensor interrupts. Adds specific support to handle the
data ready sensor trigger.
Jira: ZEP-1395
Change-Id: I092f22e35747b92a88eb71a3d162a4fc16227b45
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch fixes two "Unchecked return value" conditions into the bma280
driver.
The issue was reported by Coverity (CID 151953).
Change-Id: I2e595b67619411594cec527f358f6c3d3d034550
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The variable type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: I1193a946ea5814510e6c07668c5d05a5d91445a8
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This patch fixes unchecked return value conditions in the bme280
driver.
This issue was reported by Coverity (CID 151961, 151959, 151955).
Change-Id: I3a2dfbabd41ae52b00fa512a40e00c2e36c3b5ca
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch fixes a less-than-zero comparison of an unsigned value
condition present in bmi160 driver.
This issue was reported by Coverity (CID 152002, 152003).
Change-Id: I703066519652ac1ecdd9ddf7e97ec7dcbe2a9e27
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
convert all sensor drivers to use threads and the unified kernel API and
remove all legacy APIs.
Change-Id: Ica43ea74ecbbf85273f718f182c413a9dcd8abc6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move both semaphores and nano_work objects to unified kernel APIs.
Change-Id: Icca8a091063544c451e47201cd8e956b95010513
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Making a reference to the common work queue code should not necessarily
drag in the system workqueue, since it is possible to use a workqueue
that is not the system workqueue. This is done by moving the system
workqueue into its own code module.
Moving the system workqueue to its own code module allows removing the
NANO_WORKQUEUE and SYSTEM_WORKQUEUE kconfig options, and compiling the
common workqueue code and system workqueue all the time. They are only
linked in the final image if a reference to them exist, same as the
other kernel modules.
Change-Id: I6f48d2542bda24f4702e7c2e317818dd082b3c11
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds basic sensor driver support for the NXP FXOS8700 6-axis
accelerometer/magnetometer. Currently this driver supports
accelerometer-only, magnetometer-only, and hybrid (accelerometer +
magnetometer) modes, as well as 2g, 4g, and 8g accelerometer full scale
ranges.
This driver does not yet support any sensor triggers such as the data
ready trigger, or runtime changing of sensor attributes.
Datasheet:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Origin: Original
Jira: ZEP-721
Change-Id: Iff0f751c737196f60d5c5d3448631b57093ece34
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change-Id: I6e3c7e4e420d9b9c55bbb49cf6f13b6e09ec4bb7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Correct the text of the SYS_CLOCK_TICKS_PER_SEC #error diagnostic to
reflect the actual logic of the gate.
Change-Id: I28ad324b0b246e4a8de29b64483a97577a1b6fb7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The name read16() collides with other definitions within Zephyr. We
don't actually use this function here, so remove the definition. Fix
various other unnecessary name exports while we are here by adding
'static'.
Change-Id: I7eee8c527a62fea4e6e1bdae8a4874d8ce66596c
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The read16() name collides with other definitions within zephyr. Make
it static and fix a few other unnecessary name exports while we are
here.
Change-Id: Id72d44a6b84b8d72c7ba2d0f34b29dbc1d02f2b6
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The HDC1008_I2C_ADDR config option should be available only if HDC1008
is enabled.
Change-Id: I0d1813512396faefb609527ba5df2a0c4ea159a9
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>