This commit adds the STM32CUBE HAL for STM32L1x series MCUs.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: http://www.st.com/en/embedded-software/stm32cubel1.html
Commit: 1.8.0
Purpose: HAL layer for STM32L1
Maintained-by: External
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Using the new option --timestamps, any output from sanitycheck will have
a timestamp to help identify bottle necks and monitor execution time.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When detecting changes to boards, make sure we test all board
configurations available in that board directory, not only the main one.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We already select HAS_DTS at the arch level for X86 so we don't need to
duplicate it at the board level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
None of the UART drivers actually reference the PCI data members
declared in this header, so they are removed.
Signed-off-by: Charles Youse <charles.youse@intel.com>
Excerpt from the manual:
If ptr is NULL, then the call is equivalent to malloc(size) [...]
Without this commit, such calls end with a BUS FAULT.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add USART1 and LPUART1 nodes on stm32wb series.
Only these 2 ones are available for now on this series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of STM32Cube for STM32WB, update stm32cube
folder to enable build of STM32WB Cube package.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds the HAL code needed for the SoC for the stm32wb series.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: http://www.st.com/en/embedded-software/stm32cubewb.html
Commit: 1.0.0
Purpose: HAL layer for stm32wb
Maintained-by: External
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In this commit, a config.h header file is added to support the case
when the NET_CONFIG_SETTINGS is not used. main.c is also modified to
enable platforms that do not support IPv6. These changes are necessary
in order to allow cc3220sf_launchxl support.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Added bBreak, bRingSignal, bFraming, bParity and bOverRun
handling in cdc_acm_line_ctrl_set.
Reference: Chapter 6.5.4 of Universal Serial Bus Communications Class
Subclass Specification for PSTN Devices rev 1.2
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
The CONFIG_ prefix is reserved in Zephyr, rename CONFIG_SHIFT and
associated constants by adding a RCC_ prefix
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Add configuration, pinmux, dts and documentation for the STM32MP157
Discovery board based on the STM32MP157 SoC.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
The stm32mp1 exti ll driver is mandatory for compilation.
add it on top of stm32cubeMP1 version 1.0.0.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Provide required changes to stm32cube HAL and LL for the
STM32MP1X series MCU.
Origin: ST Microelectronics
License: BSD-3-Clause
URL: https://github.com/STMicroelectronics/STM32CubeMP1
Commit: 1.1.0
Purpose: HAL layer for STM32MP1
Maintained-by: External
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Add the initial SoC support for the STM32MP1 family. The code was
tested on STM32MP157c, but should work on any STM32MP1XX currently
available.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
The comment for:
set_target_properties(${logical_target_for_zephyr_elf} PROPERTIES
OUTPUT_NAME ${KERNEL_NAME})
was completely off-topic and making something relatively simple
incredibly puzzling and time-consuming to understand.
Re-order the if(GKSF OR GKOF) clauses so the two initializations of
logical_target_for_zephyr_elf are close to each other and so the very
short clause is not buried at the bottom of the long one.
Other minor logical_target_for_zephyr_elf comment fixes.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Sample code for AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Sample code for AMS (Austria Micro Systems) Indoor Air Quality Sensor
reading VOC and equivalent CO2 values.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
