This patch reworks the current ARM __swap() function into a C function.
Due to some issues with using svc calls withing fault handlers, we
needed to change the way we initiate a swap by removing the dependence
on svc #0.
Before __swap() is called, the system has already done an irq_lock().
Upon return from __swap(), the equivalent of an irq_lock() is done due
to restoration of the key value from the irq_lock preceeding the call.
For ARM V6M (M0/M0+), the pendsv bit is toggled and the irqs are
enabled. There is no priority masking in v6m, so it's just a global
enable. For ARM V7M, the priority mask has to be set to 0x0 to allow
for the pendsv IRQ to be taken. This is done for both via a call to
irq_unlock(0).
After this unlock, a pendsv irq will be taken, either at the tail end
of the current irq handling if we are in handler mode, or immediately
due to the pendsv being asserted (no other outstanding irqs). The next
thread will be scheduled.
Upon return from the context switch to the original
thread, the priority mask will already be correct due to the pendsv
processing.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for userspace on ARM architectures. Arch
specific calls for transitioning threads to user mode, system calls,
and associated handlers.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This PR includes the required changes in order to support
conditional compilation for Armv8-M architecture. Two
variants of the Armv8-M architecture are defined:
- the Armv8-M Baseline (backwards compatible with ARMv6-M),
- the Armv8-M Mainline (backwards compatible with ARMv7-M).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add the following application-facing memory domain APIs:
k_mem_domain_init() - to initialize a memory domain
k_mem_domain_destroy() - to destroy a memory domain
k_mem_domain_add_partition() - to add a partition into a domain
k_mem_domain_remove_partition() - to remove a partition from a domain
k_mem_domain_add_thread() - to add a thread into a domain
k_mem_domain_remove_thread() - to remove a thread from a domain
A memory domain would contain some number of memory partitions.
A memory partition is a memory region (might be RAM, peripheral
registers, flash...) with specific attributes (access permission,
e.g. privileged read/write, unprivileged read-only, execute never...).
Memory partitions would be defined by set of MPU regions or MMU tables
underneath.
A thread could only belong to a single memory domain any point in time
but a memory domain could contain multiple threads.
Threads in the same memory domain would have the same access permission
to the memory partitions belong to the memory domain.
The memory domain APIs are used by unprivileged threads to share data
to the threads in the same memory and protect sensitive data from
threads outside their domain. It is not only for improving the security
but also useful for debugging (unexpected access would cause exception).
Jira: ZEP-2281
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
In benchmark test (test_info) while making function call regs
r0 - r4 are modified into called function. Due to this value
inside r3 is getting lost.
This patch saves and restore the value in r0-r4 regs while making
function calls from assembly language.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
The API/Variable names in timing_info looks very speicific to
platform (like systick etc), whereas these variabled are used
across platforms (nrf/arm/quark).
So this patch :-
1. changing API/Variable names to generic one.
2. Creating some of Macros whose implimentation is platform
depenent.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
One of the stack sentinel policies was to check the sentinel
any time a cooperative context switch is done (i.e, _Swap is
called).
This was done by adding a hook to _check_stack_sentinel in
every arch's __swap function.
This way is cleaner as we just have the hook in one inline
function rather than implemented in several different assembly
dialects.
The check upon interrupt is now made unconditionally rather
than checking if we are calling __swap, since the check now
is only called on cooperative _Swap(). The interrupt is always
serviced first.
Issue: ZEP-2244
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch integrates the thread stack guard feature in the arm
Zephyr core.
Change-Id: I2022899cbc7a340be71cfaa52f79418292f93bae
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Future tickless kernel patches would be inserting some
code before call to Swap. To enable this it will create
a mcro named as the current _Swap which would call first
the tickless kernel code and then call the real __swap()
Jira: ZEP-339
Change-Id: Id778bfcee4f88982c958fcf22d7f04deb4bd572f
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Put the reason code in r0 and make a SVC #2 call, which will be
propagated to _fatal_error_handler as an exception.
The _is_in_isr() implementation had to be tweaked a bit. User-generated
SVC exception no longer just used for irq_offload(); just because we are
in it does not mean we are in interrupt context. Instead, have the
irq_offload code set and clear the offload_routine global; it will be
non-NULL only if it's in use. Upcoming changes to support memory
protection (which will require system calls) will need this too.
We free up some small amount of ROM deleting _default_esf struct as it's
no longer needed.
Issue: ZEP-843
Change-Id: Ie82bd708575934cffe41e64f5c128c8704ca4e48
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch updates the ARM core to use struct k_thread instead of struct
tcs. Struct tcs has been deprecated with Zephyr 1.6.
Change-Id: I1219add0bbcca4b963ffe02cd4519eca355c7719
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This directory now handles all of Cortex-M0, Cortex-M3/M4. So, just
consistently use "Cortex-M" (as used by number of files already)
without refering to a particular subarch. Also, consistently (letter
casing) spell it as "Cortex-M". A typo is fixed too.
Change-Id: I42ee09abc9a503381bca4ae437c83a8f48816ebc
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The cortex-m7 is an implementation of armv7-m. Adjust the Kconfig
support for cortex-m7 to reflect this and drop the unnecessary,
explicit, conditional compilation.
Change-Id: I6ec20e69c8c83c5a80b1f714506f7f9e295b15d5
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Precursor patches have arranged that conditional compilation hanging
on CONFIG_CPU_CORTEX_M3_M4 provides support for ARMv7-M, rename the
config variable to reflect this.
Change-Id: Ifa56e3c1c04505d061b2af3aec9d8b9e55b5853d
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Precursor patches have arranged all conditional compilation hanging on
CONFIG_CPU_CORTEX_M0_M0PLUS such that it actually represents support
for ARM ARMv6-M, rename the config variable to reflect this.
Change-Id: I553fcf3e606b350a9e823df31bac96636be1504f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The ARM code base provides for three mutually exclusive ARM
architecture related conditional compilation choices. M0_M0PLUS,
M3_M4 and M7. Throughout the code base we have conditional
compilation gated around these three choices. Adjust the form of this
conditional compilation to adopt a uniform structure. The uniform
structure always selects code based on the definition of an
appropriate config option rather the the absence of a definition.
Removing the extensive use of #else ensures that when support for
other ARM architecture versions is added we get hard compilation
failures rather than attempting to compile inappropriate code for the
added architecture with unexpected runtime consequences.
Adopting this uniform structure makes it straight forward to replace
the adhoc CPU_CORTEX_M3_M4 and CPU_CORTEX_M0_M0PLUS configuration
variables with ones that directly represent the actual underlying ARM
architectures we provide support for. This change also paves the way
for folding adhoc conditional compilation related to CPU_CORTEX_M7
directly in support for ARMv7-M.
This change is mechanical in nature involving two transforms:
1)
#if !defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
is transformed to:
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
#elif defined(CONFIG_CPU_CORTEX_M3_M4) || defined(CONFIG_CPU_CORTEX_M7)
...
2)
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
#else
...
#endif
is transformed to:
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
#elif defined(CONFIG_CPU_CORTEX_M3_M4) || defined(CONFIG_CPU_CORTEX_M7)
...
#else
#error Unknown ARM architecture
#endif
Change-Id: I7229029b174da3a8b3c6fb2eec63d776f1d11e24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Obsolete, replaced by _set_thread_return_value().
Change-Id: I23e9cfc07e43542f0965817edc3552d456fd2ef3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Also remove some old cflags referencing directories that do not exist
anymore.
Also replace references to legacy APIs in doxygen documentation of
various functions.
Change-Id: I8fce3d1fe0f4defc44e6eb0ae09a4863e33a39db
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
That module is not used anymore: it was introduced pre-Zephyr to add
some kind of awareness when debugging ARM Cortex-M3 code with GDB but
was never really used by anyone. It has bitrotted, and with the recent
move of the tTCS and tNANO data structures to common _kernel and
k_thread, it does not even compile anymore.
Jira: ZEP-1284, ZEP-951
Change-Id: Ic9afed00f4229324fe5d2aa97dc6f1c935953244
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The way the ready thread cache was implemented caused it to not always
be "hot", i.e. there could be some misses, which happened when the
cached thread was taken out of the ready queue. When that happened, it
was not replaced immediately, since doing so could mean that the
replacement might not run because the flow could be interrupted and
another thread could take its place. This was the more conservative
approach that insured that moving a thread to the cache would never be
wasted.
However, this caused two problems:
1. The cache could not be refilled until another thread context-switched
in, since there was no thread in the cache to compare priorities
against.
2. Interrupt exit code would always have to call into C to find what
thread to run when the current thread was not coop and did not have the
scheduler locked. Furthermore, it was possible for this code path to
encounter a cold cache and then it had to find out what thread to run
the long way.
To fix this, filling the cache is now more aggressive, i.e. the next
thread to put in the cache is found even in the case the current cached
thread is context-switched out. This ensures the interrupt exit code is
much faster on the slow path. In addition, since finding the next thread
to run is now always "get it from the cache", which is a simple fetch
from memory (_kernel.ready_q.cache), there is no need to call the more
complex C code.
On the ARM FRDM K64F board, this improvement is seen:
Before:
1- Measure time to switch from ISR back to interrupted task
switching time is 215 tcs = 1791 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 315 tcs = 2625 nsec
After:
1- Measure time to switch from ISR back to interrupted task
switching time is 130 tcs = 1083 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 225 tcs = 1875 nsec
These are the most dramatic improvements, but most of the numbers
generated by the latency_measure test are improved.
Fixes ZEP-1401.
Change-Id: I2eaac147048b1ec71a93bd0a285e743a39533973
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
There was a possible race condition when setting the return value of a
thread that is pending, from an ISR.
A kernel function causes a thread to pend, with the following series of
steps:
- disable interrupts
- move current thread to wait_q
- call _Swap
Depending if running on M3/4 or M0+, _Swap will either issue a svc #0,
or pend PendSV directly. The same problem exists in both cases.
M3/4:
__svc will:
- enable interrupts
- trigger __pendsv
M0+:
_Swap() will enable interrupts.
__pendsv will:
- save register context including PSP into the thread struct
If an interrupt occurs between interrupts being enabled them and
__pendsv saving PSP, and the ISR sets the pending thread's return value,
this will happen:
- sees the thread in a wait_q
- removes it
- makes it ready
- calls _set_thread_return_value
- _set_thread_return_value looks at the thread's saved PSP to poke
the value
In this scenario, PSP hasn't yet been updated by __pendsv so it's a
stale value from the previous context switch, resulting in unpredictable
word on the stack getting set to the return value.
There is no way to fix this issue and still have the return value being
delivered directly in the pending thread's exception stack frame, in the
M0+ case. There will always be a window between the unlocking of
interrupts and PendSV being handled. On M3/4, it could be possible with
the mix of SVC and PendSV, since the exception stack frame is created in
the __svc handler. However, because we want to keep the two
implementations as close as possible, and there were talks of moving
M3/4 to using PendSV only, to save an exception, the approach taken
solves both cases.
The approach taken is similar to the ARC and Nios2 ports, where
there is a field in the thread structure that holds the return value.
_Swap() then loads r0/a1 with that value just before returning.
Fixes ZEP-1289.
Change-Id: Iee7e06fe3f8ded84aff918fd43408c7f589344d9
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
There was a lot of duplication between architectures for the definition
of threads and the "nanokernel" guts. These have been consolidated.
Now, a common file kernel/unified/include/kernel_structs.h holds the
common definitions. Architectures provide two files to complement it:
kernel_arch_data.h and kernel_arch_func.h. The first one contains at
least the struct _thread_arch and struct _kernel_arch data structures,
as well as the struct _callee_saved and struct _caller_saved register
layouts. The second file contains anything that needs what is provided
by the common stuff in kernel_structs.h. Those two files are only meant
to be included in kernel_structs.h in very specific locations.
The thread data structure has been separated into three major parts:
common struct _thread_base and struct k_thread, and arch-specific struct
_thread_arch. The first and third ones are included in the second.
The struct s_NANO data structure has been split into two: common struct
_kernel and arch-specific struct _kernel_arch. The latter is included in
the former.
Offsets files have also changed: nano_offsets.h has been renamed
kernel_offsets.h and is still included by the arch-specific offsets.c.
Also, since the thread and kernel data structures are now made of
sub-structures, offsets have to be added to make up the full offset.
Some of these additions have been consolidated in shorter symbols,
available from kernel/unified/include/offsets_short.h, which includes an
arch-specific offsets_arch_short.h. Most of the code include
offsets_short.h now instead of offsets.h.
Change-Id: I084645cb7e6db8db69aeaaf162963fe157045d5a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel is now the only supported kernel, so this
option is unnessary. Eliminating this option also enables
the removal of some legacy code that is no longer required.
Change-Id: Ibfc339d643c8de16a2ed2009c9b468848b8b4972
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The unified kernel expect the default return value from a _Swap() call
to be set to -EAGAIN by the architecture code. Cortex-M3/M4 does this in
the SVC call handler, and it was missing from the Cortex-M0/M0+ before
pending PendSV.
Change-Id: I3316901186ab409f49043eb4f1972c4b0dd9a4a2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Not disabling SysTick as it is optional by the spec.
SVC not used as there is no priority-based interrupt masking (only
PendSV is used).
Largely based on a previous work done by Euan Mutch <euan@abelon.com>.
Jira: ZEP-783
Change-Id: I38e29bfcf0624c1aea5f9fd7a74230faa1b59e8b
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
The unified kernel calls a function (_get_next_ready_thread) to fetch
the next thread to run: it thus must save caller-saved registers that
are expected to hold a value before calling such function.
The callee-saved registers are available after saving them in the
outgoing thread's stack, so use some of those instead to reduce the
number of registers to save before calling _get_next_ready_thread. Also,
save caller-saved registers in callee-saved registers instead of on the
stack to reduce memory accesses.
This issue did not show up previously, probably because
_get_next_ready_thread did not use the regsiters that had to be saved,
but an upcoming optimization to that function stomps on them.
Change-Id: I27dcededace846e623c3870d907f0d4c464173bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The ARM architecture port is fitted with support for the unified kernel,
namely:
- the interrupt/exception exit code now pends PendSV if the current
thread is not a coop thread and if the scheduler is not locked
- fiber_abort is replaced by k_thread_abort(), which takes a thread ID
as a parameter (i.e. does not only operate on the current thread)
- the _nanokernel.flags cache of _current.flags is not used anymore
(could be a source of bugs) and is not needed in the scheduling algo
- there is no 'task' field in the _nanokernel anymore: PendSV not calls
_get_next_ready_thread instead
- the _nanokernel.fiber field is replaced by a more sophisticated
ready_q, based on the microkernel's priority-bitmap-based one
- thread initialization initializes new fields in the tcs, and does not
initialize obsolete ones
- nano_private includes nano_internal.h from the unified directory
- The FIBER, TASK and PREEMPTIBLE flags do not exist anymore: the thread
priority drives the behaviour
- the tcs uses a dlist for queuing in both ready and wait queues instead
of a custom singly-linked list
- other new fields in the tcs include a schedule-lock count, a
back-pointer to init data (when the task is static) and a pointer to
swap data, needed when a thread pending on _Swap() must be passed more
then just one value (e.g. k_stack_pop() needs an error code and data)
- the 'fiber' and 'task' fields of _nanokernel are replaced with an O(1)
ready queue (taken from the microkernel)
- fiberRtnValueSet() is aliased to _set_thread_return_value since it
also operates on preempt threads now
- _set_thread_return_value_with_data() sets the swap_data field in
addition to a return value from _Swap()
- convenience aliases are created for shorter names:
- _current is defined as _nanokernel.current
- _ready_q is defined as _nanokernel.ready_q
- _Swap() sets the threads's return code to -EAGAIN before swapping out
to prevent timeouts to have to set it (solves hard issues in some
kernel objects).
Change-Id: I36c03c362bc2908dae064ec67e6b8469fc573983
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The toolchain headers included an abstraction for defining symbol
names in assembly context in the situation where we're using a
DOS-style assembler that automatically prepends an underscore to
symbol names.
We aren't. Zephyr is an ELF platform. None of our toolchains do
this. Nothing sets the "TOOL_PREPENDS_UNDERSCORE" macro from within
the project, and it surely isn't an industry standard. Yank it out.
Now we can write assembler labels in natural syntax, and a few other
things fall out to simplify too.
(NOTE: these headers contain assembly code and will fail checkpatch.
That is an expected false positive.)
Change-Id: Ic89e74422b52fe50b3b7306a0347d7a560259581
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Saves and loads the non-volatile FP registers (s16-s31) when switching
between threads.
Change-Id: Ib3190452d9a70d722032ac83176eb4fbb92aca3d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Use of `ldr` triggers unaligned memory access when loading SVC
instruction to r0. This is caused by the fact that SVC is a 16-bit
instruction, hence with a 2 byte offset, we are performing an non-word
aligned access. Prevent this by using `ldrh` to load a halfwords rather
than full words.
Change-Id: Ieae60c2ce86c6cfe15c89627d3a450797ce7e714
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Removed old style file description and documnetation and apply
doxygen synatx.
Change-Id: I3ac9f06d4f574bf3c79c6f6044cec3a7e2f6e4c8
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Software interrupts or system calls aren't really appropriate for
zephyr, but we have an ongoing need in our test code to run a
function with arguments synchronously in interrupt context.
This patch introduces irq_offload() which allows us to do this without
separate initialization or having to manage fake IRQs in the
interrupt controller.
ARM assembly code contributed by Benjamin Walsh
<benjamin.walsh@windriver.com>
ARC is not yet implemented but will be in a subsequent patch.
irq_test_common.h has been removed and all test cases updated to
use the new API.
Change-Id: I9af99ed31b62bc7eb340e32cf65e3d11354d1ec7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In order to have a name according to the functionality of the feature.
This commit rename any text, function and variable related with the
Profiler name to Event logger.
Change-Id: I4f612cbc7c37965c35a64f06cc3ce5e3249d90e5
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Change all the Intel and Wind River code license from BSD-3 to Apache 2.
Change-Id: Id8be2c1c161a06ea8a0b9f38e17660e11dbb384b
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The term 'context' is vague and overloaded. Its usage for 'an execution
context' is now referred as such, in both comments and some APIs' names.
When the execution context can only be a fiber or a task (i.e. not an
ISR), it is referred to as a 'thread', again in comments and everywhere
in the code.
APIs that had their names changed:
- nano_context_id_t is now nano_thread_id_t
- context_self_get() is now sys_thread_self_get()
- context_type_get() is now sys_execution_context_type_get()
- context_custom_data_set/get() are now
sys_thread_custom_data_set/get()
The 'context' prefix namespace does not have to be reserved by the
kernel anymore.
The Context Control Structure (CCS) data structure is now the Thread
Control Structure (TCS):
- struct ccs is now struct tcs
- tCCS is now tTCS
Change-Id: I7526a76c5b01e7c86333078e2d2e77c9feef5364
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add the context switch profile point for x86 and ARM arquitectures.
Change-Id: Ib7205059104ed47b96ba75b8cfefec3ff35f6813
Signed-off-by: Yonattan Louise <yonattan.a.louise.mendoza@intel.com>
Remove function name from comment and add @brief instead.
Also capitilize first letter.
Change-Id: Ib708b49bf02e5bc89b0066637a55874e659637e0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previous comment style used RETRURNS:, use @return to comply
with javadoc style.
Change-Id: Ib1dffd92da1d97d60063ec5309b08049828f6661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The change replaces multiple asterisks to ** at
the beginning of comments and adds a space before
the asterisks at the beginning of lines.
Change-Id: I7656bde3bf4d9a31e38941e43b580520432dabc1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The new name better reflects that this file contains all private
nanokernel APIs that are used by various kernel subsystems.
Change-Id: I4c258d582e93753eec9e575fdb5f9f2109417a0f
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This commit set back .S as the assembly code extension for Kbuild.
Change-Id: Ib0119876bd0bed6617bbfbad2ca6a44e172ab042
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@linux.intel.com>
