Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
LPUART1 TX alternate function number for PB6 was not correct in the
pinmux settings for H7 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch is setting the pin to very high speed for all
the SPI2 clock outputs, for the stm32f7 soc series.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
I think people might be reading differences into 'if' and 'depends on'
that aren't there, like maybe 'if' being needed to "hide" a symbol,
while 'depends on' just adds a dependency.
There are no differences between 'if' and 'depends on'. 'if' is just a
shorthand for 'depends on'. They work the same when it comes to creating
implicit menus too.
The way symbols get "hidden" is through their dependencies not being
satisfied ('if'/'depends on' get copied up as a dependency on the
prompt).
Since 'if' and 'depends on' are the same, an 'if' with just a single
symbol in it can be replaced with a 'depends on'. IMO, it's best to
avoid 'if' there as a style choice too, because it confuses people into
thinking there's deep Kconfig magic going on that requires 'if'.
Going for 'depends on' can also remove some nested 'if's, which
generates nicer symbol information and docs, because nested 'if's really
are so simple/dumb that they just add the dependencies from both 'if's
to all symbols within.
Replace a bunch of single-symbol 'if's with 'depends on' to despam the
Kconfig files a bit and make it clearer how things work. Also do some
other minor related dependency refactoring.
The replacement isn't complete. Will fix up the rest later. Splitting it
a bit to make it more manageable.
(Everything above is true for choices, menus, and comments as well.)
Detected by tweaking the Kconfiglib parsing code. It's impossible to
detect after parsing, because 'if' turns into 'depends on'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Ensure that the SPI SCK and MOSI pins are set to very high as slower
SPI speeds will cause device hangs when used. This is due to the state
changing too fast for hardware, causing RXE to never fire and thus
hang.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Add support for the ST STM32G0316-DISCO development board. This board
features an ST STM32G031J6 MCU on a breakable SO8 to DIL8 module, a user
LED and a button.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds:
1. pin definitions for SPI1 on PE12-15 on STM32L4 devices
2. SPI3 on PA15_SPI3_NSS
Signed-off-by: Armando Visconti <armando.visconti@st.com>
* add pinmux driver. hsdk board has arduino, mikrobus and
pmod interfaces, which can be confiured for different function,
such as: gpio, spi, uart, iic.
* add introduction for arduino, mikrobus and pmod interfaces.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
To work efficiently, SPI_NSS pins require pull-up configuration.
Fix this for whole STM32 series.
Fixes#17998
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fixes#16739. Changed the STM32's SPI MISO/MOSI configurations in order
to reduce the power consumption by approximately 20uA per pin.
According to STM32's Application Notes on GPIO configuration for
low-power consumption, the input pins should be configured with internal
pull-up or pull-down resistor. If a pin is configured as a floating
input, and there is no signal present, the Schmitt trigger randomly
toggles between the logical levels induced by the external noise, thus
increasing the consumption.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
pinmux: Add the relevant definition of the spi3 pin
dts: Fix a bug, spi3 does not have a label
soc: Supplement spi3 related definition
Signed-off-by: Findlay Feng <i@fengch.me>
The i2c5 instance are used on arduino connector of
stm32mp157c-dk2.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@linaro.org>
Add eSPI Microchip XEC driver
Include support for peripheral & virtual wires (channel 0-1)
OOB and flash support can be added in the future
Fix compilation error in pinmux driver
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
