The implementation of the Network Message Cache has so far been
suboptimal, since it has treated the same packet with different TTL
values as different packets. Since one of the purposes of this cache
is to prevent unnecessary relaying, it's important that we don't let
the TTL value influence the "hash" that's used for matching messages.
This patch changes the hash to consist of most of the IV Index (three
least significant bytes of it), the sequence number and the source
address, which should give fairly optimal matching behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we receive a neighbor solicitation which does not have any
options, then there is no need to assert this condition as that
is a perfectly valid use case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If IEEE 802.15.4 reassembly function ieee802154_reassemble() returns
anything other than NET_CONTINUE, then drop that packet. Earlier
it only dropped the packet if NET_DROP was returned but the reassembly
might also return NET_OK. In that case the pkt is freed already and
pkt->frags pointer is NULL. This caused NULL pointer access in L2 when
packet was received.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This is similar to how few commands already behave if they can
provide additional info to the user if particular config options
are enabled.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_pkt_tcp_data() and net_pkt_udp_data() simply returns the start
address of the header. However the header may span over multiple
fragments, unexpected data or memory corruption might happen when
reading or writing to the pointer directly.
Use net_tcp_get_hdr() and net_udp_get_hdr() instead.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
The net_tcp_get/set_hdr() and net_udp_get/set_hdr() documentation
was not clear in corresponding header file. Clarify how the return
value of the function is supposed to be used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
udp.h is out-of-date as it accesses net buf directly. In 3604c391, it
has been replaced by net/udp.h and udp_internal.h
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Previously net_pkt.h, defined macros NET_PKT_TX_SLAB_DEFINE,
NET_PKT_DATA_POOL_DEFINE, but advertised them as intended for
"user specified data". However, net_pkt.c effectively used the
same parameters for slabs/pools, but this wasn't obvious due
to extra config param redirection. So, make following changes:
1. Rename NET_PKT_TX_SLAB_DEFINE() to NET_PKT_SLAB_DEFINE()
as nothing in its definition is TX-specific.
2. Remove extra indirection for config params, and use
NET_PKT_SLAB_DEFINE and NET_PKT_DATA_POOL_DEFINE to define
system pools.
3. Update docstrings for NET_PKT_SLAB_DEFINE and
NET_PKT_DATA_POOL_DEFINE.
Overall, this change removes vail of magic in the definition of
system pkt slabs/pools, making obvious the fact that any packet
slabs/pools - whether default system or additional, custom - are
defined in exactly the same manner (and thus work in the same manner
too).
Fixes#4327
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When hexdumping the packet, print also information if we
received / transmitted packet. Also print information if the
hexdump is before compression or not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If building a server that does not support TCP, then the
get_server_ctx() is not needed and thus needs to be compiled out.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Explicitly note that while these functions return pointers to
headers, the headers themselves may be fragmented into different
data fragments. 1a2f24f920 is an example where this might have
been overlooked.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Don't use names like "strlen" for parameters. Try and name buffer
parameters consistently.
NOTE: For several functions I removed "const" flag. This is
intentional and will be needed in upcoming patches.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Remove some left over TODOs and also fix a TODO where we need to return
the appropriate error code to generate a 4.05 response.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation reads the length portion of the COAP header to determine
the length of the coap packet. However, when encrypted via DTLS this
value seems to be getting corrupted. Let's change this calculation so
that it will work for when DTLS is both enabled and disabled. Use the
total length of the fragment data and substract back out the headers
to get a correct value.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When source address is unspecified then SAC is 1 and SAM is 00.
Uncompression does not process because context based compression
is not enabled.
Special case (SAC:1 and SAM:00) should be handled without context
based compression support.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add system workqueue information prints to "net stacks" command.
This helps debugging when figuring out which stack is running out
of space.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Enhance existing "net app" command so that it can be
used to show information about multiple connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we get MAC verification error in handshake, it could be that
everything is fine but we ran out of heap memory in mbedtls.
In this happens, suggest the user to check amount of memory
in mbedtls as it might just fix the issue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As we select net_ctx, it is useful to see who actually called
the _net_app_select_net_ctx() when debugging the call flow.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Sometimes when sending network packet, the wrong net_context was
selected which prevented data to be sent.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We should not close the TLS connection immediately if the TLS
data is not yet sent. So if user calls net_app_close() and we
still have data pending, then send the TLS data and only after
that close the connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As there can be multiple listening network contexts, it should
be possible to close one of them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server is able to listen and serve multiple incoming
connections. This commit does not add support for multiple
incoming TLS connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Vendor ID and Product ID should be assigned on build time by
respective process.
For sanity check we assign some random values which are only used for
build tests and should not be used for real products.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The stack of rd client is exhausted while running lwm2m client w/ IPv6
and network log global enabled. Increase the stack size to 1536 when
NET_LOG_GLOBAL is enabled.
Detail described at #4424
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
".well-known/core" is mainly used with method GET for performing the
resource discovery (RFC 6690). Since we are implementing a LwM2M client
and is not implement a resource directory which allow others to do the
resource registration (POST to .well-known/core). Only GET method is
allowed for the usage. Report 4.5 (Method Not Allowed) if other methods
are requested.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Modify zoap_options_to_path() to return error when URI contains
character other than digits and return 4.04 NOT FOUND to caller.
PATH such as "/1a/2/3" was treated as "/1/2/3" after parsring
which is incorrect.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Return 4.05 Method Not Allowed when path is empty ('/') to the
caller for it's only use by bootstrap delete. This change also avoid the
empty path being treated as request targeted at 0/0/0.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
1) Respond NOT FOUND to caller when object doesn't exist
2) Report as internal server error when OP not handled
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Such option should be use carefully. Printing out in/out packets is
extremely verbose.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the pkt is corrupted and the offset would be larger than
the actual packet length, then print information about that and
drop the packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The main purpose of recv_thread is to process incoming events from the
radio and also any buffered items waiting to be dispatched to the Host
and that are pending because of lack of Host buffers.
When an iteration of the recv_thread obtains a element from the radio it
needs to process it immediately, either sending it straight away to the
Host or appending it to the queue. This was not the case before this
patch, where the concurrency of a buffered packet with one coming from
the radio would cause the latter to be "dropped", causing missing
packets.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Applications may want to be notified when various events
happen in the LwM2M rd client. Let's implement an event
callback which sends: connect, disconnect and update events.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
CoAP allows a proxy to be used when transferring data (CoAP-CoAP and/or
CoAP-HTTP) by creating request on a specific URI path and by using the
Proxy URI CoAP option. Create specific Kconfig options for the proxy
server address and port, until a parser gets implemented.
Code tested with Californium acting as CoAP proxy.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
[michael.scott@linaro.org: rebased on net_app + lwm2m_message
refactoring + firmware update changes.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During firmware download via block-wise transfer, we can see
packets occaionally get re-transmitted (normal logic in the
pending / retry functions). However, both of these packets
end up coming through the reply handler and we should ignore
any block-wise transfer that has a current value less than
where we expect to be.
NOTE: This fixes K64F ethernet transfers where we were getting
too many packets back in the handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
UDP packets can be lost in heavy traffic. Normally we can handle this
with pending packet processing for packets which have not been responded
to with an ACK. However, due to the time it takes for firmware to
download via CoAP, an extra level of retries should be added.
The process works like this:
Normal pending packets will try to send 3 times fairly quickly.
If that fails, then the timeout callback is called for the firmware
download process. A retry counter is incremented and the timeout
callback perform a new packet send of the block-wise transfer
packet that is missing, until the retry counter hits a limit (3)
and then the transfer is aborted.
This allows for a longer "outage" to happen during firmware transfer
and the process can still succeed.
NOTE: This patch does not fix a current bug where the pending process
is not re-sending the packets correctly, it only makes the process
more stable with a better chance to work.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When a packet expires after the pending retries we call
lwm2m_release_message() to free up resources. This includes
cleanup of the pending structure which calls net_pkt_unref on
the pending packet. This would normally free up the packet
memory. However, earlier in the pending processing we add a ref
to the packet so that normal send processing doesn't free up
the memory. This meant we were leaking packet memory every
time we had an expiration due to timeout.
Let's do an unref prior to calling lwm2m_release_message() to
make sure the packet memory is freed correctly.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Previously, firmware support wasn't initializing the retransmit work
or the extra network packet pools. Let's fix that.
NOTE: While this fixes the setup of retransmit work, the actual
attempts to re-send packets which are pending is failing. Needs
another follow-up fix.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Create an internal function lwm2m_engine_context_init() which sets
the extra packet pools and initializes retransmit work internal to
the LwM2M engine.
This function will be used by firmware pull support which establishes
a new LwM2M context for downloading firmware.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In the case of a proxy server translating HTTP -> COAP (known in
the code as "separate reply"), we were leaking lwm2m_message structures.
This was due to pending objects being cleared out during the first ACK,
and no other way of finding a matching message when the follow up packet
was received. Let's add a second match for reply to make sure we can
find our matching message resources.
NOTE: This change renames find_msg_from_pending() to find_msg() and
makes it a static function as it's only used by the lwm2m_engine.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This is a useful message announcing that the RD client state machine
is starting for a particular connection. If the log level is set
low so that DBG messages are hidden, then this message goes away.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
1. Add handling block1 option in handle_request(). The basic idea is
to declare structure block_context at compiled time and use "token"
as a key to pick up the on-going block cotext. It should be able to
support multiple blockwise transfer concurrently
2. Use write callback implemented in lwm2m_obj_firmware to deal w/ the
update state transition and than call the callback registered by the
application
3. move default_block_size to lwm2m_engine.c to share between
lwm2m_engine and lwm2m_obj_firmware_pull
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on LwM2M net_app changes.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
OPAQUE resource type might/might not have data_ptr/data_len setup
depending on the implementation. This introduce an issue that when
OPAQUE resource is written from the server side, the ones w/ none
setup will not be able to get the data at post_write_cb()
Modify to setup data_ptr/data_len as incoming buffer and buffer size
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
1. Parse firmware pull URI
2. Add lwm2m_firmware_get/set_update_cb() for application to register
callback. This is because we want to check the update_state before
we pass to the application
3. Add lwm2m_firmware_get/set_update_result() and
lwm2m_firmware_get/set_update_stat() to manage the state transition
as well as the sanity check
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on net_app framework and
lwm2m_message refactoring.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
With future patches we will need to parse URLs in the registration
client and firmware object. Enable it by default when LWM2M is
enabled.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
There was a missing net_buf_unref() for the response to reading the
controller static addresses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If there is no connection to server, then _net_app_select_net_ctx()
will return NULL. This is perfectly fine and we can just continue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use the remote address to determine what address family to bind.
This prevents extra context to be created. In order to avoid
parsing the peer address string multiple times, the client
init function is re-factored.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently this is defined as a k_thread_stack_t pointer.
However this isn't correct, stacks are defined as arrays. Extern
references to k_thread_stack_t doesn't work properly as the compiler
treats it as a pointer to the stack array and not the array itself.
Declaring as an unsized array of k_thread_stack_t doesn't work
well either. The least amount of confusion is to leave out the
pointer/array status completely, use pointers for function prototypes,
and define K_THREAD_STACK_EXTERN() to properly create an extern
reference.
The definitions for all functions and struct that use
k_thread_stack_t need to be updated, but code that uses them should
be unchanged.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some doxygen directives were missing from dns_pack.h file.
Also make function header documentation look better.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This creates mDNS responder and serves configured IP addresses
to the callers which want to resolve .local addresses.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can configure hostname of the device in Kconfig. This can
be used by mDNS responder to answer <hostname>.local queries.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
net_context_sendto() returns an error if dest address is NULL.
If dest address is available, net_conext_sendto() should be used.
Otherwise, net_context_send() should be used.
Fixes#4347
Signed-off-by: Aska Wu <aska.wu@linaro.org>
With the introduction of CoAP and other protocols, URL parsing is
be needed when HTTP_PARSER is not. Let's split out the existing
functionality of URL parsing into it's own CONFIG and let
HTTP_PARSER use it by automatically selecting HTTP_PARSER_URL when
HTTP_PARSER is enabled.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add skeleton for HCI vendor extenstions and convert the nRF5x-specific
static address setting to use the HCI VS commands instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a connection is disconnected with outstanding unacked packets, the
Host has no way to signal or acknowledge their processing to the
Controller, since it is illegal to send a Host Number of Completed
Packets command when the connection is not up. Instead, consider the
outstanding packets as acked in order not to affect the correct flow
control.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The feature bits for Proxy and Friend were missing in the composition
data and heart beat messages.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When CONFIG_STDOUT_CONSOLE is not selected, there is no printk()
function. An alternative (printf) must be used.
This fix was taken from tests/crypto/mbedtls/src/mbedtls.c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Both count and period must be non-zero for message publication
Stop publication when count becomes zero
Add count to debug message in hb_publish
Signed-off-by: Steve Brown <sbrown@cortland.com>
Use some preprocessor trickery to automatically deduce the amount of
arguments for the various _SYSCALL_HANDLERn() macros. Makes the grunt
work of converting a bunch of kernel APIs to system calls slightly
easier.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
It's possible to get number of free pkts/buffers with just
CONFIG_NET_BUF_POOL_USAGE, whereas CONFIG_NET_DEBUG_NET_PKT
depends on CONFIG_NET_LOG and adds quite a bunch of other
overhead. Also, give a hint that this option should be enabled
to get free buffer numbers.
Additionally, use unambiguous "Total" wording to represend the
maximum capacity of data structures, instead of previous "Count".
"Count" (or at least counter) is intuitively something which can
change, so not seeing any other numbers, it's very easy to assume
that it's actually number of free buffers (because that's the
information a user may be interested in in many cases).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
There have been situations where the remote stacks cannot responds
within a second, so increases it to 2 seconds. The timeout has to be
relatively short as the channel cannot be reused while disconnecting.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
MPS shall never be bigger than MTU + 2 as the remaining bytes cannot
be used since the SDU is limited to length + MTU.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add implementation to support Coded PHY update procedure
with packet transmit time restrictions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use S8 coding Rx chain delay timings to calculate the PA
pin assertions when in Coded PHY.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Always use S8 Rx Chain Delay instead of the actual Rx-ed
packet coding. I believe, as the packet always start with
S8, hence S8 timings when used the tIFS is near correct
value.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When calculating and setting up the header compelte timeout
use S8 coding Rx chain delay.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In the commit dd52b8ea02 ("Bluetooth: controller: Fix
first connection interval timing"), instead of using just a
tick unit as workaround, microseconds corresponding to a
tick unit was used while calculating the window offset to be
used at the connection update instant. This introduced an
error in scheduling the first event with new connection
parameters, causing supervision timeout of connection update
procedure.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Mesh Profile Specification v1.0, 4.4.1.2.8:
"When an element receives a Config Model Subscription Add message
or a Config Model Subscription Virtual Address Add message that
is not successfully processed (i.e., it results in an error condition
listed in Table 4.113), it shall respond with the Config Model
Subscription Status message, setting its fields to the values
of the corresponding fields (i.e., the identically named fields)
of the incoming message and setting the Status field to a status code
(defined in Table 4.113), and setting all other fields to 0."
The same applies to other Model Subscription messages.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's possible that tx_notify still contains items when a Disconnect
Complete happens. Since the normal path for processing tx_notify is
not taken when the connection is not in CONNECTED state, we must make
sure to process the list latest in conn_cleanup() that's called as one
last thing before the connection object is freed up.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the caller has passed net_pkt to prepare_segment(), then
it is caller responsibility to unref it in a case of error.
Fixes#4292
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch adds composite support for USB class drivers.
It acts as a relay between the usb_device stack and
class or function drivers.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add common device descriptor for USB class devices.
The common descriptor allows easy configuration of Manufacturer,
Product, SerialNumber strings and PID/VID.
It also allows future support for composite devices.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some chips are smart enough to handle the ACK request flag on
transmitted frames, so it's unneccessary for the L2 to wait for it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is both required in L2's radio part as well as it might be useful
on some ieee802154 radio drivers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These are now fully replaced by set_filter() thus removing their usage
by the L2 layer.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the hw supports filtering, L2 will apply the ieee address, short
address or PAN ID filters.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using radio's get_capabilities, it is possible to know if the driver can
get CSMA work handed-over.
For now, up to device drivers to use
CONFIG_NET_L2_IEEE802154_RADIO_CSMA_CA_* parameters.
Let's see if it will be interesting at some point to enable runtime
modification of these parameters.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixed a missing reset of FC feature on HCI reset. This
feature provided a simple connection handle based event
exclusions, but this is no longer needed with the
support for controller to host flow control. This feature
should be removed in the future.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
A connection might have gotten disconnected by the time that an ACL
buffer is free up, in which case there is no need to send a HCI
command for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We now have macros which should significantly reduce the amount of
boilerplate involved with defining system call handlers.
- Macros which define the proper prototype based on number of arguments
- "SIMPLE" variants which create handlers that don't need anything
other than object verification
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When a peer master performed a PHY update procedure with no
change, the state machine was not released. This blocked
any future local initiation of the procedure and also
leading to termination of connection with reason LMP
response timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use new _SYSCALL_OBJ/_SYSCALL_OBJ_INIT macros.
Use new _SYSCALL_MEMORY_READ/_SYSCALL_MEMORY_WRITE macros.
Some non-obvious checks changed to use _SYSCALL_VERIFY_MSG.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fixed the usage of NRF_AAR peripheral for controller privacy
to clear events on configure and on every radio ISR entry.
Without this fix, there was spurious AAR matches leading to
controller asserts.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To avoid making a system call for every character emitted, there is now
a small line buffer if userspace is enabled. The interface to the kernel
is a new system call which takes a sized buffer of console data.
If userspace is not enabled this works like before.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
PHY Update procedure timeout was started without transition
to the state that waits for the procedure to complete. This
prevented the timeout from being reset on successful
completion of the procedure and eventually leading to a
connection termination with reason LMP Response Timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Connection Parameter Request Procedure's Connection
Update Procedure initiation to calculate the offset rather
than selecting offsets from an out-of-bound memory area.
The symptoms of the bug was noticed as a supervision timeout
due to use of incorrect offset communicated to peer and a
wrong offset used in scheduling the connection events.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Instead of hard coded 1280 bytes MSS, use the MTU of the link
for MSS. The minimal MSS is still 1280 which is mandated by
IPv6 RFC.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When the peer slave rejects a Connection Parameter Request
Procedure, the controller proceeds to perform a Connection
Update Procedure without clearing the procedure timer that
causes the connection to terminate eventually. This is
fixed by clearing the procedure timeout when the Connection
Update Procedure completes.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If a peer master role has support for Connection Parameter
Request Procedure set in its supported features but would
send an Extended Reject Ind as response to the procedure
then the controller incorrectly initiated a Connection
Update Procedure which is not permitted in a slave role.
This would lead to connection timeout after the used instant
in the invalid Connection Update Procedure.
This is fixed by initiating a Connection Update Procedure
only if in a master role.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adding net_mgmt_event_notify_with_info() which lets the event notifier
to pass dedicated data along with the event. The size of data that can
be passed must be limited to the biggest data passed (which will be
currently IPv6 + prefix).
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use the define generated by the DTS instead of using the FLASH_ALIGN
alias. The latter is an internal mcuboot name. We shouldn't need it in
Zephyr itself.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Current coap library fails to parse or prepare if packet is more
than one fragment. Added support to handle multi fragment packet.
Also well-known/core api used to prepare coap packet and send it
through net context api immediately. This is goind to be problematic
if user doesn't enable net context. Also user can not encrypt coap
packets. Now api will return prepared coap packet to application.
Application will send it to peer.
Jira: ZEP-2210
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
ZOAP library has certain limitations in parsing and preparation of
coap messages. It can handle only on single network fragment. If
network packet is split between multiple fragments it fails. This
patch is just copy and rename of 'zoap' to 'coap'.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
802.15.4 IP-based networking requires 6LoWPAN layer and won't work
correctly without it. So, if NET_L2_IEEE802154 is select,
automatically select NET_6LO. This is similar to what BLE L2
does (NET_L2_BT causes selection of NET_6LO).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is similar to the changes made previously to other network
components: if user selected NET_LOG_GLOBAL, they really mean
they want logging (first of all, error/warning logging) across
the entire network stack.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Due to timeout checking the minimum lifetime must be 15 seconds,
and we're storing the lifetime as an unsigned short so set the
maximum to 65535.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Callbacks are setup for the following states:
- ENGINE_DO_BOOTSTRAP
- ENGINE_DO_REGISTRATION (first registration)
- ENGINE_REGISTRATION_DONE (subsequent client updates)
- ENGINE_DEREGISTER
In most cases, if a timeout occurs the registration engine goes back to
ENGINE_INIT. The exception is a timeout during client update, which
forces the state machine back to ENGINE_DO_REGISTRATION (skipping a
boostrap).
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Sending an lwm2m message is too difficult. It requires pending / reply
and other structures to be configured and set by various portions of
the library. There is also no way to know if a pending message ever
encounters a timeout.
Let's fix this by simplifying the internal LwM2M engine APIs for
handling lwm2m messages:
1. A user calls lwm2m_get_message(lwm2m_ctx) which returns the first
available lwm2m message from an array of messages
(total # of messages is set via CONFIG_LWM2M_ENGINE_MAX_MESSAGES).
2. Next the user sets all of the fields in the message that are
required (type, code message id, token, etc)
3. Then the user calls lwm2m_init_message(msg). This initializes the
underlying zoap_packet, pending and reply structures.
4. Once initialized, the user creates their payload in msg->zpkt.
5. When the user is ready to send, the call lwm2m_send_message(msg).
6. And if for some reason an error occurs at any point, they can free
up the entire set of structures with: lwm2m_release_message(msg).
Included in the refactoring is a timeout_cb field which can be set in
the LwM2M messages. If a pending structure ever expires the engine
will call the timeout_cb passing in the msg structure before it's
automatically released.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Instead of using a magic reference to 8 for token length, let's
establish a define for MAX_TOKEN_LENGTH and then use it for both
variable definitions and to make sure tokens are valid. Also,
Correct the handling of a special token length value (0xFF) which
lets lwm2m_init_message() know to skip token generation. We were
using a -1 value here previously (on a u8_t variable).
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When the net-shell needs to send something to network interface,
it will check if the target address is found in neighbor cache and
then use that network interface. If the address is not found in nbr
cache, then the default interface is used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
send()/sendto() aren't "front facing" functions, so when user calls
them, context type hopefully should be already validated by other
functions. They are also on critical path of app/network performance,
so getting rid of extra check helps a little bit too. This also
fixes a warning of "err" possibly being used non-initialized.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The implementation is based on net app API. It sends the request and
parses the server reply by following some suggestions mentioned in the
secion "SNTP Server Operations" of RFC 4330.
The system uptime is used as the transmit timestamp of client request
This lib can work on those devices without RTC.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Since the Zephyr HCI VS extensions apply to both the Host (using them
for additional functionality) and the Controller (implement the commands
and events), it make sense to make this a common setting in order for it
to be configurable in a way that applies to both.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
sendto() and recvfrom() are often used with datagram socket.
sendto() is based on net_context_sendto() and recvfrom() is based on
zsock_recv() with parsing source address from the packet header.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
This patch makes net_context_sendto() work independently without calling
net_context_connect() first. It will bind default address and port if
necessary.
Also, since receive callback should be provided before sending data in
order to receive the response, bind default address and port to prevent
providing an unbound address and port to net_conn_register().
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Introduce net_pkt_get_src_addr() as a helper function to get the source
address and port from the packet header.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
The PA/LNA feature is not functional on nRF51x series due to added
interrupt latency. Disable this feature unconditionally for those ICs to
avoid unexpected behavior.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Other parts of the networking subsystem may use net_pkt_ip_hdr_len() on
a packet that has been encrypted for use with DTLS. Let's restore that
value here so those areas don't receive an erroneous 0 value.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Issuing HCI reset command while having connections sometimes
hung the controller.
ll_reset supplied invalid stop ticker id to role_disable
when trying to stop all connections. Connection role does
not utilize stop ticker. The invalid ticker id supplied
referenced memory outside the pool of tickers and based on
what the content is in RAM there, the controller would hang
trying to stop connections.
Fixed by not calling the ticker_stop interface with invalid
ticker ids.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The IPv6 address parameters in net_ipv6_send_na() can be const
as the function will not modify them. This avoids compile warning
about parameter constness.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is useful to return the neighbors in net_ipv6_nbr_foreach()
groupped by network interface. This way the caller has them
already in proper order and does not need to re-group them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Proxy configuration messages are allowed (in fact required) to use
unassigned addresses, so they should be exempt from this check.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The test failure may be e.g. because of an unknown company id, and in
that case the spec expects us to ignore the message.
With this patch it should be possible to pass MESH/SR/HM/RFS/BI-01-C.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A previous patch which moved dispatching the health publish callback
to a later moment introduced a regression where the period divider
does not get updated when it should. In fact, having the divider as
part of the Health Server context is redundant, since the same
information is already stored generically in the model publication
context. Switching to using the model publication context makes things
simpler and ensures that the value is always up-to-date.
With this patch it is possible to pass MESH/SR/HM/CFS/BV-02-C.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We should ignore invalid addresses (helps pass
MESH/NODE/CFG/LPNPT/BI-01-C). Also fix a copy-paste issue in an error
log.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values all need to be zeroed when heartbeat subscription is
disabled. This makes it possible to pass MESH/NODE/CFG/HBS/BV-01-C.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There was no handler functions for adding, removing and looking up
IPv4 multicast addresses in the network interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user tried to bind to IPv4 multicast address, then the
operation failed and returned error.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the network interface does not support IPv4 like IEEE 802.15.4
or Bluetooth, then do not print IPv4 information for those interfaces.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Implement the Read Build Information VS command. This returns a UTF-8
encoded string, which is extendable by the user via a new Kconfig
option.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the Zephyr VS command that allows a Host to write a public
Bluetooth Address to the Controller in order to allow Hosts to provide
their own public Bluetooth addresses.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If the data parameter in net_pkt_insert() is NULL, then just
insert amount of data but clear the area instead of copying.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User was able to tweak IPv6 hop-limit so introduce similar
feature for IPv4 Time-To-Live value.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the caller of http_client_send_req() sets the timeout to
K_NO_WAIT, then the function would still wait for a while before
returning to the caller.
Jira: ZEP-2624
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
From section 3.4.5.3 in the Mesh Profile Specification 1.0:
"A node shall implement a Local Network Interface."
Removing the Kconfig option also helps clean up quite a lot of code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_mesh_net_relay() function needs to allow TTL <= 1 for the local
network interface since that's the code path that locally originated
outgoing packets take.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Mesh Profile Specification v1.0, 5.3.3:
"On the PB-ADV bearer, when the receiver has received all segments of
a transaction, the receiver shall calculate the FCS for the received
Provisioning PDU, and if it matches the FCS field in the Transaction
Start PDU, it shall send a Transaction Acknowledgment PDU after
a random delay between 20 and 50 milliseconds."
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Mesh specification recommends defaulting to the company ID in the
composition data when no other ID is relevant (e.g. in error cases or
if the app has not provided a callback).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Encrypting and sending a message takes a considerable amount of time
which makes the publication period longer than expected.
With this patch it is possible to pass MESH/SR/HM/CFS/BV-02-C test.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The branch for handling the case when the app has not provided a
callback for health faults was encoding the payload in a wrong way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid signedness issues with some compilers, like icx, use 'char *'
instead of 'unsigned char *' for the at_client buffer.
Fixes#3600
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The code was passing the wrong first parameter to the sdu_len_is_ok()
function.
Fixes#3985Fixes#3984
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The code was accessing wrong neighbor data when it received DAO
message. This corrupted nbr->iface pointer which was clearly seen
by "net nbr" shell command. The corruption then caused random
crashes or hangs when network interface via that pointer was
accessed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the ethernet packet destination MAC address is NULL when sending
IPv4 multicast or broadcast packet, then we must set it as otherwise
we might to access NULL pointer data.
Fixes#1544
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds a new state NET_IPV6_NBR_STATE_STATIC which never timeouts
which is required in case of RFC 7668 which doesn't allow publishing
the address:
https://tools.ietf.org/html/rfc7668#section-3.2.3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It makes no sense to respond with Pairing Failed PDU to another
Pairing Failed PDU.
Jira: ZEP-2620
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add following commands to fs shell:
- rf <filename>
- read <filename> [<offset> [<length>]]
- write <filename> [-o <offset>] <byte1> [<byte2> ... [<byteN>]]
- trunc <filename> [<length>]
For writes without offset specified, new data is appended to file.
For truncaces without length specified, 0 is default value.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This patch moves code to create absolute path of file/directory to
separate helper since the same code is used in few places.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This patch adds filesystem interface implementation for NFFS.
Default configuration for mem slabs sizes are the same as in Mynewt.
Origin: Original
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Move the use of tIFS software switching PPI index set up by
one position to make place for use of PA/LNA implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Earlier design captured AA twice in the first Rx in a slave
connection event and retained one of the capture until end
of event to calculate drift.
Design updated to use single capture of AA and save the
first AA capture in a slave connection event in RAM instead.
This frees up a PPI channel in the controller design.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Document internal the purposes of various Tx/Rx PDU end
capture setup.
Also, removed any redundant capture of packet end.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Minor refactor of radio_tmr_start to reduced duplicate
assignments common in if-then-else control path.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Composite multifunction USB devices should be able to know about
configuration change, implement it through existing callback.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
mcuboot_constraints.h had FLASH information related to the SoC that
should be maintained as part of the SoC and not in the subsystem. Also
fixed Makefiles to check for IMG_UTIL Kconfig and not MCUBOOT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In a case gateway is not set drop packet early otherwise bogus
ARPs for 0.0.0.0 are sent.
...
[net/arp] [DBG] find_entry: (0xa8006720): dst 0.0.0.0
[net/arp] [DBG] find_entry: (0xa8006720): [0] iface 0xa800cd80 dst
0.0.0.0 ll 00:00:00:00:00:00 pending 0xa800a7c0
[net/arp] [DBG] find_entry: (0xa8006720): ARP already pending to
0.0.0.0 ll 00:00:00:00:00:00
[net/arp] [DBG] net_arp_prepare: (0xa8006720): Resending ARP
0xa800a380
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
If IPv6 is disabled, then it is useless to try to resolve
IPv6 address because "struct sockaddr" does not have enough
space to store IPv6 address.
Fixes#1487
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is useful to clone just the net_pkt which does not have any
data fragments linked to it.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is useful to enable error/warning logging across the net
codebase (less useful for debug level logging, but that's true
for CONFIG_NET_LOG_GLOBAL already).
Implementation-wise, instead of keeping adding to long list of
"select"'s in CONFIG_NET_LOG_GLOBAL and thus introduce component
inter-dependencies, add "default y if NET_LOG_GLOBAL" to
individual components' logging options.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
At the moment we print "Sending ARP packet" even if we found ARP entry
and send the packet directly.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This is the first part of a large refactoring of LwM2M library
message functions and will simplify observer handling later.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
All throughout the LwM2M library we use sockaddr values which are
basically the same as the net_app_ctx's remote addr. There's no
reason to keep these extra sockaddr values around. The net_app
framework client won't accept incoming requests on sockaddr other
than the one we're connected to.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This is the final stage of moving the LwM2M library internals to
the net_app APIs. This means we can support DTLS and other
built-in features in the future. All of the logic for
establishing the network connection is removed from the sample
app.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In preparation for the move to net_app APIs, we will need
to pass net_app_ctx structures around to the following
functions:
lwm2m_udp_sendto()
udp_request_handler()
Let's add the parameter as net_context for now so the
transition will be smoother later.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This allows use to associate easily the replies / pending operations
with a specific network connection.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The LwM2M library does not use net_app APIs internally. To help
this effort let's establish a user facing structure "lwm2m_ctx"
(similar to http_client_ctx and mqtt_ctx) and start it off by
wrappering the net_context structure.
Future patches will add user setup options to this structure and
eventually remove the net_context structure in favor of a net_app_ctx.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
If no gateway is set, an ARP request for 0.0.0.0 will be sent out,
which is confusing, so log as an error. Of course, logging will
happen only if enabled.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The IPv4 multicast address to MAC address mapping was missing
the 4th byte high bit clearing.
We also need to have some storage for the multicast MAC address.
This was missing which could cause NULL pointer access.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This implements mDNS client from RFC 6762. What this means that
caller is able to resolve "hostname.local" names using multicast DNS.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes a tx_pkts slab leak since the cloned pkt was referencing the
original pkt slab but was not originated from it (net_pkt_unref uses
pkt->slab when releasing the pkt).
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Because a next networking API call will lead to a crash. Given that
logging can be easily disabled (disabled by default so far!), don't
be shy and call by the name (i.e. error).
Jira: ZEP-2105
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the IP address string is empty, then it is no use trying
to parse it. This was seen when handling DNS server strings when
user has made a mistake and defined the DNS server addresses
incorrectly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Updated debug pin mapping so that the outputs are on P3 pin
head on all nRF5x Development Kits.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed the configuration of NRF_CCM for 2M PHY connections.
Now faster 2M data rate mode will be used when a connection
is in 2M PHY.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use correct NRF_AAR enable macro defines from Nordic MDK.
Old code funtionally worked fine even though not setting
the correct enable value.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed a bug in the implementation of Connection Parameter
Request Procedure when initiated in master role caused the
connection to terminate with reason LL response timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The status in the Command Complete event was uninitialized, leading to
incorrect contents of the event parsed by the Host. Correctly initialize
the status to success.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
During testing it was discovered that directed advertising
timeout is missing implementation to handle the timeout
happening while next event is already in preparation.
The consequence was that after the event ticker expired,
the counter is shutdown, stalling the setup PPI from
starting the erroneous advertising, leaving the controller
in an invalid hung state.
This has been fixed by correctly handling the cases, stop
between prepare and event, and stop inside radio advertising
event. The fix takes care of putting the radio active
callback and HF clock in the correct states.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adjust length of the packet before setup_ipv4_header() which actually
might increase packet size if there is not enough space available.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Whenever the HCI ACL flow control is violated by the Host, a Data Buffer
Overflow event is now issued by the Controller (if enabled) to notify
the Host of the buffer overrun.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Create support for registering a callback that will be called
if the device leaves or joins IPv6 multicast group.
Jira: ZEP-1673
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Commit cd35742a2 missed one unref too many on pending packet which was
triggering a crash which commit 0b8434f08 tried to fix, but it generates
a leak when there is not pending entries left in arp core. Finally,
fixing what cd35742a2 should have done: removing the extra unecessary
unref after sending the pending packet.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Errors has been ignored when using TLV writer to create/write object
instance/resources. Modify to propagate the error back to the caller.
To reproduce the issue, try to create IPSO light control object
instances twice. Since the default instance count is 1, the second one
should be rejected and responded w/ error. But the current
implementation will respond w/ 2.04.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We did not check the requested object/object instance/resource exists or
not before we adding an observer. Correct it by checking the existence
first.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We should stop sending out notification to the peer when the
object/object instances requested to be observed is removed
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We were using sys_slist_remove() to remove object, object instance and
observer w/o passing the previous sys_snode_t to it (NULL).
This will instruct the function to treat the node as the list head and
result in unexpected behavior after the removal.
Correct it by using sys_slist_find_and_remove() or passing the previous
node to the function.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When a request demands to create a new object instance, it will search
whether the request object instance exists or not. However, current
implementation does not reset the lwm2m_engine_obj_inst at the time it
is deleted. It only removes the object instance from the sys list.
Correct the behavior by resetting both object instance and resource
instances at the time it's deleted. Also, consolidate function
lwm2m_delete_handler() and lwm2m_delete_obj_inst().
To reproduce the issue, try to create light control object instance
(/3301), delete the created instance and create it again. You shall find
following error message dumped.
> [ipso_light_control] [ERR] light_control_create: Can not create
instance - already existing: 0
> [lib/lwm2m_engine] [ERR] lwm2m_create_obj_inst: unable to create obj -
3311 instance 0
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
If the packet is put pending because ARP request need to be
done, then do not unref original packet.
Fixes#1416
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add a command "net arp" to net-shell. This new command will
print ARP cache contents if IPv4 and Ethernet are enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 725be227 ("net/mgmt/event: Commands must be > 0 so
masking them works") prevented IPv6 address setting when an
application was initialized. The check in subsys/net/lib/app/init.c
needs to be adjusted because of that change.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There were bunch of config options in tests/net, net-shell and
wpan_serial sample, and those options had wrong name so they
were ignored by the code.
Fixes#1428
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Store image in sequence of certain blocks.
Module is intended to be use by a higher-level
image management protocol module
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
read, update status
trigger flashing
erase image bank
Module is intended to be use by a higher-level
image management protocol module.
Signed-off-by: Fabio Utzig <utzig@apache.org>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
When new connection is accepted, the TCP context variables like
sequence number etc. were not properly set.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For IPv6 check_ip_addr in subsys/net/ip/net_core.c makes a
NET_DBG call to report when a net_pkt is missing a destination
address. An analogous NET_DBG call has been added to the IPv4
destination address checking.
Signed-off-by: John Andersen <john.s.andersen@intel.com>
prepare_arp() was unreferencing original pkt (called pending there) in
case of error.
net_prepare_arp() was always unreferencing pkt, though it could have
been already unreferenced by prepare_arp() as seen previously which is
an extra bogus unref in this case.
And in case it returned NULL, ethernet_send() would return NET_DROP
which in turn would make net_if's tx code to unref again the pkt.
This patch ensures pkt is unrefed only once and at the right place.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The TCP state string is only printed if CONFIG_NET_DEBUG_TCP is
defined. If that is not the case, then the "net conn" command
should not print the "State" column name as the state will not
be printed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Added missing asserts to catch high CPU use in radio ISR and
latencies, without which if radio packet pointer is not set
correctly, would cause spurious transmissions and invalid
behavior.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Optimised the get() function in nRF5 hal rand implementation
to reduce number of probable branching operations.
This is needed to reduce nRF51 platform's CPU use in radio
ISR when using the fast encryption setup implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Move the code to acquire the RSSI sample after critical
control path that processes PDUs.
This is needed to reduce the time taken to assign the next
packet ptr inside radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To meet CPU time usage restricts inside radio ISR on nRF51
SoCs, use ccflags -Ofast when using fast encryption setup
implementation in the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Default to n the support for Data Length Update and
PHY update procedures on nRF51 SoCs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed an assert when peer responded with unknown rsp to
slave feature request when an existing another control
procedure was in progress.
This assert happened with a BT v4.0 peer implementation that
was performing a channel map update and local controller
initiated a slave feature request, receiving an unknown
response.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Without this fix there is an issue when doing PB-ADV provisioning
with PTS. We keep retransmitting Public Key which is ACKed by PTS and
this leads to transaction timeout as PTS does not send confirm probably
because it keep receiving PK from us.
This patch also makes sure that transaction id is between 0x80 - 0xFF
Signed-off-by: Łukasz Rymanowski <lukasz.rymanowski@codecoup.pl>
Needed for following PTS test cases:
MESH/NODE/PROV/UPD/BV-10-C
MESH/NODE/PROV/BI-02-C
Signed-off-by: Łukasz Rymanowski <lukasz.rymanowski@codecoup.pl>
Fix the control and data packet management implementation
discovered during conformance testing.
This fixes:
TP/SEC/MAS/BV-12 [Master Start Encryption: Overlapping
Procedure]
TP/SEC/MAS/BV-13 [Master Start Encryption: Overlapping
Procedure with LL_SLAVE_FEATURES_REQ]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Privacy on nRF51 is not passing the conformance and qualification tests
due to the time it takes to execute the privacy code while in ISR. Until
we come up with a way of optimizing and/or deferring the work, do not
allow privacy on nRF51 targets.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the macros generated during the build and located in version.h to
fill in the version information in the Read Version Information VS
command. Additionally reply with the correct hardware identifiers when
running on Nordic hardware.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Seems due to incorrect rebase in commit 07270e52ba
("Bluetooth: controller: Coding style and refactoring"),
commit 95d55a2bfc ("Bluetooth: controller: Do not skip
one-shot tickers with slot"), and
commit 4ba2bb0d1c ("Bluetooth: controller: Be fair when
pre-empting a ticker"), a pointless expression was
introduced, fixed it.
Coverity-CID: 171563
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 817245c564.
In certain cases the peer seems to discard the FIN packet we are
sending, which means that the TCP stream is not closed properly.
This needs more work so revert this for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was setting the wrong bit of the Static OOB Type when a
static value has been provided.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When new socket context is created on accepting connection to a
listening socket, its recv_q FIFO should be initialized. Without
initialization, this worked by a chance when FIFO structure was
simple, but recent change to add dlist to it (which now needs
proper initialization) exposed this issue.
Jira: ZEP-2576
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the query name is already in numeric format, there is no
need to send the query string to DNS server as we can just
convert it ourselves.
Jira: ZEP-2562
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes IP address parsing from DNS init and
replaces it by call to net_ipaddr_parse().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_ipaddr_parse() will take a string with optional port
number and convert its information into struct sockaddr.
The format of the IP string can be:
192.0.2.1:80
192.0.2.42
[2001:db8::1]:8080
[2001:db8::2]
2001:db::42
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes an assert during connection establishment when the
initiator overflows the initiator window in time while
sending the CONNECT_IND PDU. The actual window is one low
frequency tick less, hence corrected the check that permits
the transmission of CONNECT_IND PDU inside the initiator
window.
Symptom was, stopping of the scanner's ticker succeeds on
connection establishment, but next interval prepare was
already run when continuous scanning was used, breaking the
design, hence there was an assert.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If network context is closed, send FIN by placing it to the end
of send queue instead of sending it immediately. This way all
pending data is sent before the connection is closed.
Jira: ZEP-1853
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Implement the Zephyr Read Key Hierarchy Roots command, returning the IR
and ER present in nRF5x ICs when compiling for those.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the first Vendor-Specific Command of the Zephyr specification
other than the 3 mandatory ones already present in the codebase, along
with a Kconfig option to enable and disable the presence of the VS
commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
TLS and DTLS are not related to each other so allow DTLS to be
enabled even if TLS is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net app" command was accessing NULL pointer if TLS and UDP were
enabled but DTLS was not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier we modified the original pkt chain when creating IPv6
fragments. This is not a proper way as the original chain might
still be used in TCP when re-sending a message. So when fragmenting
the packet, clone it first and leave original packet intact. This
occupies litle more memory but is now safe.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is very unlikely to happen but the device will access null
pointer if we do not properly check the return value of header
check function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When trying to figure out where ICMP / TCP / UDP header is located
in net_buf, print more information about what we were doing if the
header cannot fit the first fragment. This is much needed infomation
in debugging weird issues.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Using memcpy() to copy net_pkt is not safe because there are
pointers inside. So use the new net_pkt_clone() to do that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is needed when one wants to copy the whole fragment chain
and its head pointer net_pkt.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP header was stripped by _net_app_ssl_mux() when it received
IP packet. This is fine but if the application expects the get
the IP header, then there is a problem. Fix this by saving IP
header to ssl_context and then putting it back in front of the
packet when the data is passed to application.
Note that this IP header is not used by net_app when the packet
is sent because TLS/DTLS creates a tunnel for transferring packets
and user can only sent packets via this tunnel.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
k_delayed_work_cancel now only fail if it hasn't been submitted which
means it is not in use anyway so it safe to reset its data regardless
of its return.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is necessary in order for k_queue_get to work properly since that
is used with buffer pools which might be used by multiple threads asking
for buffers.
Jira: ZEP-2553
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Refactor the Connection Parameter Request Procedure to be
separate from and not overlap the variables of the
Connection Update Procedure.
Also, added missing implementations to pass all Connection
Parameter Request Procedure related Conformance Tests.
Jira: ZEP-1918
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implement the LE Read Channel Map HCI command, along with making the
reading of the multi-byte channel map value from the connection pointer
thread-safe in case the ISR triggers while we are reading the value.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Although the current BLE controller only supports a single TX power (0
dBm), the qualification tests require the 2 Read TX Power to be
present and supported in the controller, so implement them while
returning always 0 dBm.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When the CONFIG_BT_CTLR_CONN_RSSI option is set, the connection RSSI is
available in the controller, and can be reported to the Host via the
Read RSSI command. Implement the command, which is required for
qualification.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The original commit 8ebaf29927 ("net: http: dont timeout
on HTTP requests w/o body") was intended to handle a case
where an HTTP response had been retrieved from the server but
the HTTP parser couldn't meet the criteria for calling
"on_message_complete". For example, a POST to a REST API
where the server doesn't return anything but an HTTP
status code.
It was a really bad idea to check a semaphore count. There
is a lot of kernel logic built into semaphores and how the
count is adjusted. The assumption that the value is 0
after the k_sem_give() is incorrect. It's STILL 0 if
something is pending with a k_sem_take(). By the time
k_sem_give() is done executing the other thread has now
been kicked and the count is back to 0.
This caused the original check to always pass and in turn
breakage was noticed in the http_client sample.
Let's do this the right way by setting a flag when
on_message_complete is called and if that flag is not set
by the time we reach recv_cb, let's give back the semaphore
to avoid a timeout.
Jira: ZEP-2561
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The HTTP header field pointers are saved for each HTTP request.
But the counter that saves the pointers was never reset to initial
value when the connection was dropped. This meant that the header
field values were only proper for first HTTP request.
Jira: ZEP-2463
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server needs global enable/disable status instead of only being
able to enable or disable just the TLS server part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we have specified AF_UNSPEC when initializing application
server local address, then we try to bind to both IPv4 and IPv6
addresses. The old code did not honor the port number in this
case but used some random value for port.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has specified a specific local address, then honor that
and do not try to bind IPv4 context if only IPv6 is defined,
and vice versa for IPv6.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Zeroing-out all bytes from a connection structure when it's
unregistered ensures all state from a previous connection is gone and
can't be mistakenly reused.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If either a remote or a local address were supplied to the
net_conn_register() function, the IP stack would proceed to copy
sizeof(struct sockaddr) bytes from the respective remote_addr
or local_addr pointers, regardless of the actual size of the storage
these pointers point to.
Use the proper size depending on the socket address family.
Coverity-ID: 173630
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
There are 2 possible interpretations regarding the address to return in
response to the Read Peer RPA HCI Command:
1) The RPA that the local controller generates to be used in certain
packets it sends
2) The RPA generated and used by the peer device in its packets
We used to return 1) but our interpretation turned out to be incorrect
when reading the HCI test specification, so this commit switches to
returning 2).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If CONFIG_NET_DEBUG_APP was defined, but neither NET_APP_SERVER nor
NET_APP_CLIENT, build failed due to net_app_cb() haven't beeen
defined. So, define it to empty in this case.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In the ll_rl_pdu_adv_update() function, the check to verify if we are
dealing with an item from the resolving list or else with a simple
standard non-privacy enabled device was left over from the previous
iteration, which used negative values. Replace that check with the
proper current one, using the size of the rl array as an indicator of
whether the index is valid.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Due to varying remainder value, first interval will need to
consider the remainder value used in microsecond timing from
the start of the initiator window.
Also the tx chain delay and ready delay must be substract
after the window offset is calculated.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Read Remote Version Information command is supported on the BLE
controller, enable the bit in Read Local Supported Commands to reflect
this.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Setting just IPv4 address as was allowed before isn't enough for
real-world usage (e.g. accessing DNS and outside servers in general).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Per LwM2M spec (7.3.2.4 Operation on Object):
"If the payload (New Value) conveys an Object Instance ID in conflict
with one already present in the LwM2M Client, the complete request
MUST be rejected and a "Bad Request" error code MUST be sent back."
Let's do that.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Per LwM2M specification 7.3.2.4, "Optional Resources MAY be conveyed
in the "New Value" parameter as well; the LwM2M Client MAY ignore the
optional resources it doesn't support."
Update TLV/JSON writer to ignore error when object fields are not
found (treated as optional resource). This will allow the resources
supported being written.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: re-worked patch post addition of CREATE
operation.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Prior to this patch, a CREATE operation was handled as a WRITE operation
after the object instance was created. This becomes problematic when
handling of optional resources differs between these 2 operations.
Let's introduce an actual CREATE operation and use it later to create
these differences.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We are returning EINVAL from content format write ops when an object
field definition is not found (an optional field which is not
implemented). Instead, return ENOENT which lets the LwM2M engine
know to send ZOAP_RESPONSE_CODE_NOT_FOUND to the LwM2M server at the
end of handle_request().
NOTE: This behavior is not correct when we call the writer right after
a CREATE operation where the data is assigned to resources for the
first time. This case will be handled in a follow-up patch once we're
able to distinguish between a WRITE and a CREATE in the write op
handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
POSIX requires struct sockaddr's field to be named "sa_family"
(not just "family"):
http://pubs.opengroup.org/onlinepubs/009696699/basedefs/sys/socket.h.html
This change allows to port POSIX apps easier (including writing
portable apps using BSD Sockets compatible API).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Fix controller assert due to a bug introduced in commit
07270e52ba ("Bluetooth: controller: Coding style and
refactoring").
This reverts implementation to original way it was and the
calculation of the ticker expiry will now not overflow the
range of the RTC peripheral, which is a 24 bit counter.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_pkt_get_reserve_data ignores the timeout parameter when in isr,
using K_NO_WAIT instead, which can lead to invalid fragment.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per LwM2M specification 5.3.1 Register, report "ct=11543" when JSON is
supported. Also, report the resource type as rt="oma.lwm2m" when "ct="
presents.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Per LwM2M specification 5.3.1 Register. When object instances are
available, object ID can be ignored in registration message
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
According to LwM2M specification 5.2.7.3 Bootstrap DISOCVER,
security object is only reported to the bootstrap server.
Correct the behavior to (1) report server object to the server
(2) do not report security object at registration time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Fix checks for BT_HCI_RAW and move default range after the other range
options, required by Kconfig to avoid overwriting other options.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This is how it's called in the main docs, so use this same phrase in
Kconfig and samples too.
Also, added some articles to docs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The RSSI value is an 8-bit signed integer. Since the Link Layer works
only with positive unsigned integers, translate into a negative number
at the HCI layer.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This option enables full debugging output for memory allocations.
As that can produce lot of output and slow down the device under test,
it is disabled by default.
The previous CONFIG_NET_DEBUG_NET_PKT will collect information about
memory allocations but will not print any output. Use "net mem" or
"net allocs" commands in net-shell to see the memory allocation status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because the name of the memory pool can be quite long, print
it last so that the columns get aligned nicely.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are not in ESTABLISHED state, then there is no need to
try to resend any pending data packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the expire send timer expires, then it sends the packet.
If that happens, then we must not try to send the same packet
again if we receive ACK etc. which can cause re-sends to happen.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the packet sending is slow then we must NOT increment the ref
count when re-sending it. This is unlikely but can happen if there
are lot of debug prints etc. extra activities that prevent the driver
to actually send the packet fast enough.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that the sent flag is only set after we have really
sent the packet and the driver has verified that.
If the net_pkt_set_sent() is called while still in tcp.c, then
depending on how fast the device is, it might happen that the
retry timer expires before the packet is actually sent. This was
seen in frdm-k64f with ethernet and various debug prints activated.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is a backlog entry when TCP context is released, then
cancel the ACK timer if one exists.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that a network packet is sent after calling
http_response_send_data(). Othwerwise the packets might be
piling up and not sent in timely manner.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some older C libraries do not have errno for EPFNOSUPPORT.
Fixes issues with newlib in some versions of Xtensa XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The initial function prototype did not have 'inline' in it,
resulting in a compiler warning with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's never a good idea to redefine functions as macros if intended
to be unused in some configuration
- "statement with no effect" warnings
- "unused argument" warnings
- No type checking done if the macros are used
These have been redefined as empty inline functions.
Fixes compiler warnings with XCC.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The second 'const' is misguided, indicating that the returns pointer
value itself cannot be changed, but since pointers are passed by value
anyway this is not useful and was generating warnings with XCC.
The leading 'const' indicates that the memory pointed to is constant,
which is all we needed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Inline functions declared in header files need to be declared
static. Fixes a compiler warning with XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Older value of 256 was introduced in 1.7 times. Testing on
BOARD=96b_carbon with 2 weeks old codebase however showed that TX
thread stack however can grow to 324 bytes. Finally, with the
latest master, following stacks are reported on BLE disconnect
(with CONFIG_INIT_STACKS enabled):
rx stack (real size 1024): unused 452 usage 572 / 1024 (55 %)
tx stack (real size 384): unused 16 usage 368 / 384 (95 %)
Two outcomes:
1. TX stack needs increase.
2. Over time, the stack usage grows, plus variations in SPI
drivers should also be taken into account.
So, increase the stack size to 416 bytes, to leave some headroom
beyond the immediate values seen on 96b_carbon.
Jira: ZEP-2510
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Currently, the HTTP_NETWORK_TIMEOUT setting is hard-coded as 20 seconds.
Not every application may want to wait that long, so let's change this
to a CONFIG option: CONFIG_HTTP_CLIENT_NETWORK_TIMEOUT
NOTE: This also removes HTTP_NETWORK_TIMEOUT from the public http.h
include file. It was not being used externally to HTTP client sources.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Add a sample application that allows a Zephyr-based Bluetooth
controller to interface with an HCI driver via SPI. This sample
implements the same BT SPI protocol already as Zephyr's HCI SPI
driver.
Currently, the sample only supports the legacy SPI API.
Provide a single configuration file, avoiding board-specific
files. Some board-specific configuration information must be provided
via other means:
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_PIN
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Since Extended Scanner Filter Policies is an independent feature from
Controller-based Privacy, split it out so it can be built independently
and included without it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A TCP FIN message is passed on to user apps as a tcp_received_callback
with a NULL pkt parameter. This means the connection is closing and
the app should do whatever cleanup it needs as there will be no further
callbacks for the current TCP connection.
Currently, if a HTTP client request doesn't receive a "body" which
the HTTP parser can use to trigger on_message_complete, then the request
will end up timing out and most apps will think an error has occurred.
Instead, let's handle the TCP FIN message and return the waiting
semaphore, leaving the app to deal with whatever has been set in the
current HTTP context response data (IE: http_status).
This fixes using HTTP client to send POST data to servers which
only respond with HTTP_OK status and no body.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Unless offset was specified, it should default to 0, whereas
previously, value from the last command was used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
"Network Application Support" itself is renamed from "Network
Applications" and also includes net_app API.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Whenever privacy is enabled, we support the Extended Scan Filter
Policies functionality, and therefore we must show it in the bitfield of
LE supported features for the controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Avoiding segmentation in the GATT-based Mesh Proxy protocol requires
having an RX buffer length of at least 77. We could round it up to 80
since there's otherwise wasted space, however there's also
BT_HCI_RESERVE to consider, so to avoid pushing over the 4-byte
boundary for certain HCI drivers just leave the size at 77.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is needed in order to get information which function is
doing the ref. With inline function this was not possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of printing [net/net_pkt], print [net/pkt] if debug log
is enabled for network packet allocator. The double net in earlier
print is redundant information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always have CONFIG_NET_IPV6_MAX_NEIGHBORS parents,
use CONFIG_NET_RPL_MAX_PARENTS when creating the parent table.
Default value for max parents is the max neighbors so no
functionality changes are introduced here.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always having CONFIG_NET_IPV6_MAX_NEIGHBORS number
of items in neighbor pool, store the neighbor count in the pool
and use that value when traversing the neighbor table.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow user to define what kind of network the RPL should serve.
Currently options will be either ANY or IEEE802154. If there
is only one network interface in the system, then ANY will take
the default network interface and use that. If there are multiple
network interfaces, then one should not use ANY as the default
network interface might not be the expected one.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print network interface where the DIO, DIS or DAO was sent. This is
useful if we have multiple network interfaces in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When printing network interface specific data, print also
the type of the network interface (ethernet, bluetooth etc).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user has not specified CONFIG_NET_APP_MY_IPV4_ADDR or
CONFIG_NET_APP_MY_IPV6_ADDR, the value is set to "" in this case.
This will be converted to ANY IP address which is not useful
to be set to the network interface. So check this and just
continue the init in this case without setting the IP address.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The documentation says that the API will automatically append the
net_buf fragment to the end of network packet fragment chain.
This was not the case and current only user for this API in
echo-server sample appended the fragment itself. The fix is to
automatically append the fragment to the end of fragment chain.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
1. According to the specification 5.3.1, it's a MUST to specify
(1) content format: app link format (2) supported lwm2m version.
Also, we should use text/plain instead of LWM2M's (obsolete).
2. Use LWM2M_FORMAT_OMA_TLV as default accept format when accept option
is not given from the caller for TLV is a MUST have in LwM2M spec and
it can deals w/ multiple resources read
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Save in observe_node_data so that later on we can select the correct
content format requested by the caller at the first time
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Function do_write_op_tlv() uses in->inbuf and in->insize as a looping
condition to iterate through items in TLV payload and call
do_write_op_tlv_item() to update the value.
However, do_write_op_tlv_item() will override the value before calling
for fitting the usage of lwm2m_write_handler() function without restore
them. (lwm2m_write_handler() is also called by plain text/json writer
and is expecting in->inbuf is the start of buffer and in->insize as the
length of the buffer)
This will result in errors in do_write_op_tlv().
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
RFC-7230 "HTTP/1.1 Message Syntax and Routing" Section 5.4
describes the "Host" header formatting. If Zephyr user
specifies a host string as a part of the HTTP client request
structure, we end up sending an incorrect HTTP header due
to a missing "Host :" text.
Fix this by prepending "Host: " to the header data before
the user supplied host string.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
openocd object was put in a library causing it to be stripped. We want
those symbols in the final ELF to allow debugging with openocd, building
those as objects like the rest of the kernel keeps the symbols in the
kernel.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
sprint_token is only used by SYS_LOG_DBG, so only build it when
CONFIG_SYS_LOG_LWM2M_LEVEL > 3.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Separate response can happen when handling block transfer for firmware
updates, and to avoid duplicating the lwm2m_udp_receive function, create
and additional flag to allow handling CoAP separate response messages.
This is required to avoid removing the reply callback, since a new
message (with a valid token) will be received later from the server.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Simplifly net_context_sendto calls and also allows to easily debug every
send/receive lwm2m call.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Implement the 4.2 event LE Directed Advertising Report, used for
scanners in a privacy-enabled controller to report directed advertising
events whose TargetA cannot be resolved by the local controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add implementation to support PHY update procedure with
packet transmit time restrictions.
This fixes:
TP/CON/SLA/BV-49-C [Initiating PHY Update Procedure Packet
Time Restrictions]
TP/CON/SLA/BV-50-C [Responding to PHY Update Procedure
Packet Time Restrictions]
TP/CON/SLA/BV-52-C [Initiating PHY Update Procedure Packet
Time Restrictions, No Change]
TP/CON/SLA/BV-53-C [Responding to PHY Update Procedure
Packet Time Restrictions, No Change]
TP/CON/MAS/BV-49-C [Initiating PHY Update Procedure Packet
Time Restrictions]
TP/CON/MAS/BV-50-C [Responding to PHY Update Procedure
Packet Time Restrictions]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The CONFIG_BT_WAIT_NOP define is used only by
zephyr/subsys/bluetooth/host/hci_core.c.
It is also the only config in drivers/bluetooth that is in use when
BT_CONTROLLER is enabled. Moving it into the bluetooth subsystem
allows us to restructure the drivers/kconfig code such that the entire
Bluetooth driver menu option is omitted when the BT_CONTROLLER is
enabled.
Moving it will also mean that all configs in drivers/bluetooth will
now be related to configuring the source code in drivers/bluetooth.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
If the device has multiple network interface, then we must not
blindly use the default one but get the IEEE 802.15.4 network
interface when setting radio parameters in the shell.
Jira: ZEP-2432
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print route information by groupping them for each network
interface like this:
IPv6 routes for interface 0xa8007140
====================================
IPv6 prefix : 2001:db8::212:4b00:0:3/128
neighbor : 0xa80065e0
link addr : 00:12:4B:00:00:00:00:03
IPv6 prefix : 2001:db8::212:4b00:0:1/128
neighbor : 0xa8006660
link addr : 00:12:4B:00:00:00:00:01
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "net rpl" command to net-shell which will return both static
RPL configuration from Kconfig, and dynamic run time configuration
of the nodes and parents.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create net_rpl_foreach_parent() function that will traverse
through all the parents and return their information via callback.
This is needed by net-shell in later commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If debug level was low but debugging was activated, then some
of the debug variables were left unused.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_rpl_repair_root() and net_rpl_set_root_with_version()
functions were static which prevented global repair when using
an instance id. Making those functions global allows RPL network
repairing from shell for example.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit b14586c3ca ("net: rpl: RPL route entry was fetched
too late") dropped the DAO packet too early which prevents the
RPL root node functionality. Rework the earlier commit so that
Coverity issues are fixed but the RPL DAO message is also properly
handled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
IPSO Smart Objects are a set of template objects based on the LwM2M
object framework which are designed to represent standard hardware
such as temperature and humidity sensors or light controls.
Let's add a place for these objects to live as well as an initial
temperature sensor object.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Origin: SICS-IoT / Contiki OS
URL: https://github.com/sics-iot/lwm2m-contiki/tree/lwm2m-standalone-dtls
commit: d07b0bcd77ec7e8b93787669507f3d86cfbea64a
Purpose: Introduction of LwM2M client library.
Maintained-by: Zephyr
Lightweight Machine-to-Machine (LwM2M) is a protocol stack extension
of the Constrained Application Protocol (CoAP) which uses UDP
transmission packets.
This library was based on source worked on by Joakim Eriksson,
Niclas Finne and Joel Hoglund which was adopted by Contiki and then
later revamped to work as a stand-alone library.
A VERY high level summary of the changes made:
- [ALL] sources were re-formatted to Zephyr coding standards
- [engine] The engine portion was re-written due to the heavy reliance
on ER-CoAP APIs which are not compatible to the Zephyr CoAP APIs as
well as other Zephyr specific needs.
- [engine] All LWM2M/IPSO object data is now abstracted into resource
data which stores information like the data type, length, callbacks
to help with read/write. The engine modifies this data directly (or
makes callbacks) instead of all of the logic for this living in each
object's code. (This wasn't scaling well as I was implementing
changes).
- [engine] Related to the above change, I also added a generic set of
getter/setter functions that user applications can call to change
the object data instead of having to add getter/setting methods in
each object.
- [engine] The original sources shared the engine's context structure
quite extensively causing a problem with portability. I broke up the
context into it's individual parts: LWM2M path data, input data and
output data and pass only the needed data into each set of APIs.
- [content format read/writer] sources were re-organized into single
.c/h files per content formatter.
- [content format read/writer] sources were re-written where necessary
to remove the sharing of the lwm2m engine's context and instead only
requires the path and input or output data specific to it's
function.
- [LwM2M objects] re-written using the new engine's abstractions
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In the 08 Feb 2017 V1.0 LwM2M specification page 80 mentions: in
response to a "Notify" operation for which it is not interested in
any more, the LwM2M Server can send a "Reset Message".
Leshan server sends this CoAP RST response and it does not contain
the originating message token (which is also how the packet flow looks
on page 81 of the LwM2M spec). Using the current ZoAP sources, the
client has no way of matching back to observation which needs to be
cancelled.
Let's add a match for message ID of a reply where there is no token
to handle this case.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
[ricardo.salveti@linaro.org: Handle both piggybackend and separate
response (id doesn't need to match, only token).]
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
There are two kinds of HCI implementations. Bluetooth drivers in
drivers/bluetooth that implement HCI by using a wired serial
transport layer to talk to an external controller chip. And a
bluetooth controller in subsys/bluetooth/controller that directly
talks to an internal on-chip controller node.
Currently, when the the subsys/bluetooth/controller is used there
still exists exposed to the user a bluetooth driver configuration
menu, even though no external bluetooth driver is in use. This is due
to a dependency on certain configs in driver/bluetooth that are needed
even though no external controller is used.
This patch moves one of these configs, BLUETOOTH_HCI_RESERVE, from
drivers/bluetooth/hci/Kconfig to subsys/bluetooth/host/Kconfig such
that eventually we can omit the entire Bluetooth driver menu option.
This re-organization does not change when the config can be enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Fix incorrect return data type, which causes controller to
hang generating random numbers.
Fixes bug introduced in commit d90095b556 ("Bluetooth:
controller: Use random numbers in adv and enc setup")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The specification requires the scanner to verify that the AdvA present
in a scan response matches the AdvA that was sent in the original scan
request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to get random numbers in ISR. And fixed
implementation to use random numbers in advertisement random
delay and encryption setup procedure.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For an accepted socket, we should set our receive callback and start
to queue packets ASAP (in the accept callback itself). Otherwise,
(if done in accept() call like before) we may miss to queue some
packets.
This issue wasn't exposed with slow SLIP and with emulated QEMU, but
easily exposed with Ethernet on a real hardware.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We need to define __LINUX_ERRNO_EXTENSIONS__ if newlib is being
used otherwise there is a compile error about ESHUTDOWN errno
value missing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Fix typo'd "&&" when checking bit value
- Don't use NET_EVENT_IPV6_ADDR_ADD for checking mask value
due to combination of bits: _NET_EVENT_IPV6_BASE |
NET_EVENT_IPV6_CMD_ADDR_ADD
Instead use NET_EVENT_IPV6_CMD_ADDR_ADD so the check works
when NET_EVENT_IPV6_ROUTER_ADD is enabled.
Tested fix with echo_server on x86 qemu where it was previously
broken.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The existing check for the TargetA address in directed advertising
events was incorrect. In fact the specification states:
"An initiator that has been instructed by the Host to use
Resolvable Private Addresses shall not respond to directed connectable
advertising events that contain Public or Static addresses for the
target’s address (TargetA field)."
Hence, reject TargetA values that have not been successfully resolved
when the controller is generating its own RPAs.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Unlikely to happen but make sure parent neighbor exists when
probing it.
Coverity-CID: 173635
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no parent found with a specific dag, then we have
to check this in order not to access NULL pointer.
Coverity-CID: 173637
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the parent is not found when adding DAG, then just return.
We must check the parent pointer as it can be NULL.
Coverity-CID: 173638
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to complex overflow checks that are error prone.
Coverity complained that the original diff check was always
false.
Coverity-CID: 173639
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There was dead code when handling IPv6 Hop-by-hop option.
The extra option value check can be removed as it is useless.
Coverity-CID: 173642
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity complains about non-checked return values here. This is false
positive as the return values do not need checking in this special
case because we are closing the socket.
Coverity-CID: 173646
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity complains about reversed src and dst fields when sending
DAO ack back to originator. This is false positive.
Coverity-CID: 173650
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check the return value of k_poll() as instructed by Coverity.
If debugging is enabled we print error if this happens, otherwise
this error is ignored. In our case the return value should always
be 0.
Coverity-CID: 173652
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is be possible that the local address was not properly
resolved in which case the local_addr variable could be NULL.
This will cause NULL pointer access if the variable is used.
Coverity-CID: 173656
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The RPL route entry variable "extra" was resolved inside an
if-statement and the code was always returning from it.
This meant the the later code dealing with "extra" was never
executed. Fixed by moving the resolving of "extra" a bit
earlier so that the "extra" variable has always a proper value.
Coverity-CID: 173659
Coverity-CID: 173654
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The TX send function will return status < 0 if there is an error
when sending. This status value was incorrectly checked.
Coverity-CID: 173660
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix compiler warnings resulting from passing C string literals to
functions expecting an unsigned char pointer.
Jira: 2443
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To be able to get a hit on the AAR whenever a Scan Response is received,
enable it in the state transition.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add missing checks for the logic that discriminates between whitelisting
and non-whitelisting filtering, so that we do not fall into an
unsuspected false positive.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As we buffer incoming packets in receive callbacks, we must decrease
receive window to avoid situation that incoming stream for one socket
uses up all buffers in the system and causes deadlock. Once user app
consumes queued data using recv() call, we increase window again.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This fixes the existing situation that "if application buffers data,
it's the problem of application". It's actually the problem of the
stack, as it doesn't allow application to control receive window,
and without this control, any buffer will overflow, peer packets
will be dropped, peer won't receive acks for them, and will employ
exponential backoff, the connection will crawl to a halt.
This patch adds net_context_tcp_recved() function which an
application must explicitly call when it *processes* data, to
advance receive window.
Jira: ZEP-1999
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This enables IPSP node role which requires IPSS GATT service to be
registered.
Jira: ZEP-2451
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds NET_REQUEST_BT_ADVERTISE which can be used to advertise
IPSS service so the remote devices can connect to it.
Jira: ZEP-2451
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some network interfaces such as bluetooth 6lowpan can start without
an assigned IP address and then later once the connection is up a
router advertisement broadcast will assign the IP address.
The net_app framework will timeout out during network init if a value
cannot be parsed from CONFIG_NET_APP_MY_IPV6_ADDR. Let's adjust
the framework to handle a missing value there and fill it in later
when the IPv6 address is added to the interface.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Rework the ctrl_lrpa_get() function so that it doesn't require an
assignment to be present inside the if statement, yielding smaller and
safer code.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Advertising reports generated by a scanner require the controller to
look up the resolving list to supply the host with an ID address instead
of the RPA that has been sent over the air.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the actual scanner address to copy the generated RPA into, instead
of mistakenly copying it into the advertiser's address.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Whenever trying to generate a local RPA to send a scan request or a conn
ind, verify that it can be generated (i.e. no NULL IRK provided by the
Host) and fall back to using the public/random address if required.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the hardware expects big-endian IRKs but the common generation
function expects it in little-endian, copy and reverse the peer IRK
before generating RPAs.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
ReST defines interpreted text roles where text enclosed by single quotes
can be "intrepreted", for example :ref:`some name` becomes a link to
a label anywhere in the doc set named "some name", :c:func:`funcname()`
becomes a link to the API documentation for "funcname", and
:option:`CONFIG_NAME` becomes a link to, in our case, the documentation
for the generated Kconfig option.
This patch fixes uses of `some name` (without a role) by either adding
an explicit role, or changing to ``some name``, which indicates inline
code block formatting (most likely what was intended).
This is a precursor to changing the default behavior of interpreted
text to treat `some name` as :any:`some name` (as configured in
doc/conf.py), which would attempt to create a link to any available
definition of "some name".
We may not change this default role behavior, but it becomes an option
after the fixes in this patch. In any case, this patch fixes incorrect
uses of single-quoted text (possibly introduced because GitHub's
markdown language uses single-quoted text for inline code formatting).
Jira: ZEP-2414
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Implement the LE Enhanced Connection Complete HCI event, but include it
only when controller-based privacy is enabled, since it is only relevant
with it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since a connection attempt can fail and will still generate an LE
Connection Complete event, check the status from the LL control module
before incrementing the HCI connection count used for flow control.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The Test ID was incorrectly being added as 4 bytes (size of a pointer)
instead of the intended 1 byte.
This fixes Coverity CID 173643.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current 960 is at least too small under qemu_x86:
ecc stack (real size 1024): unused 36 usage 988 / 1024 (96 %)
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The nRF5 AAR requires the packet pointer to be placed exactly 3 bytes
before the beginning of the address. Since we don't use the S1 extra
length byte, substract one from the address of the radio packet pointer.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The currently supported hardware in the LL requires big-endian IRK
values to properly function. Reverse the order of the IRK bytes coming
from HCI to address this issue.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The nRF5's AAR was being improperly configured, leading to a NULL
scratch pointer which made it not function at all.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A new net-shell command "net app" will print information about
network app users in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add API that allows net-shell to get net_app context information
that can be used to debug net_app connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to make sure that the ISR never gets an incomplete or partial
local RPA, use pointers to share the local RPA between thread mode and
ISRs. Pointer updates are guaranteed to be atomic at least on ARM
Cortex-M.
Additionally add support for using local RPAs when initiating a
connection or sending a scan request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the hardware is only able to resolve the first address in the
packet, use the existing functionality to resolve a potential TargetA
RPA in software to verify if it matches the local device.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit introduces controller-based privacy for both the scanner and
the initiator roles. All the features in the specification are
implemented except:
* RPA resolution for directed advertising (TargetA address)
* RPA generation for scan requests and conn ind packets
Follow-up patches will cover the 2 items of functionality still missing
from the basic implementation. Hosts not using controller-based privacy
should not be affected by this change.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If peer has previously configure to received service changes indications
any changes to the database during the time it has been disconnected
shall be indicated once it reconnects:
[bt] [DBG] sc_process: (0x004065b4) start 0x000a end 0x0014
[bt] [DBG] sc_save: (0x004065b4) peer b8:8a:60:d8:17:d7 (public)
start 0x000a end 0x0014
[bt] [DBG] bt_gatt_connected: (0x00405240) conn 0x00405aa0
[bt] [DBG] gatt_ccc_changed: (0x00405240) ccc 0x00400b30 value 0x0002
[bt] [DBG] sc_ccc_cfg_changed: (0x00405240) value 0x0002
[bt] [DBG] sc_restore: (0x00405240) peer b8:8a:60:d8:17:d7 (public)
start 0x000a end 0x0014
[bt] [DBG] sc_process: (0x004065b4) start 0x000a end 0x0014
[bt] [DBG] gatt_indicate: (0x004065b4) conn 0x00405aa0 handle 0x0008
[bt] [DBG] sc_indicate_rsp: (0x00405240) err 0x00
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_gatt_indicate return 0 in case of success, not true, so
SC_INDICATE_PENDING was flag was not set when it should.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Control and Data packet Tx queue management updated to be
optimal and defer control packet responses when Tx is paused
during encryption setup.
This fixes:
TP/SEC/MAS/BV-12 [Master Start Encryption: Overlapping
Procedure]
TP/SEC/MAS/BV-13 [Master Start Encryption: Overlapping
Procedure with LL_SLAVE_FEATURES_REQ]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix handling of different procedure collision when receiving
a PHY update request and handling of reject extended
indication.
This fixes:
TP/CON/MAS/BV-47-C [Handling Protocol Collision – Different
Procedure – Channel Map],
TP/CON/SLA/BV-46-C [Handling Protocol Collision – Different
Procedure – Channel Map] and
TP/CON/SLA/BV-48-C [Handling Protocol Collision – Different
Procedure – Connection Update]
conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing PHY update event generation on same procedure
collision,
This fixes TP/CON/SLA/BV-44-C [Handling Protocol Collision –
Same Procedure] conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix PHY update procedure intiation to use correct No Change
value in MtoS and StoM when there is no change to respective
PHYs. Also, added missing HCI event generation under this
case.
This fixes TP/CON/MAS/BV-41-C [Initiating PHY Update
Procedure] conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
As ticker can only drift in 32kHz units, the slave Rx
window should consider a +/- one 32kHz unit in addition to
+/- 16us jitter of the master. Hence, for the current
implementation the slave Rx window jitter is +/- 48us.
Future improvement can be done by using remainder of 32kHz
unit drift to reduce this jitter to +/- 16us.
With this fix 20ppm clock accuracy passes conformance TIM
tests (else 251-500ppm had to be used).
Problem was not seen in real life as master do not have a
+/- 16us jitter.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix terminate procedure timeout when supervision timeout
equals connection interval. In this case, avoid timing out
in the first event of procedure initiation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix slave implementation to initiate reject_ext_ind if peer
supports reject_ext_ind.
This fixes:
TP/SEC/SLA/BV-11-C [Slave Sending Reject_Ind_Ext]
conformance test in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix handling invalid control PDUs by generating
LL_UNKNOWN_RSP PDU.
This fixes:
TP/PAC/SLA/BV-01-C [Unknown Packet from Master]
TP/PAC/MAS/BV-01-C [Unknown Packet from Slave]
conformance tests in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix access address generation to correctly have two
transitions in the six MS bits and add other missing checks.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Minor cleanup of Encryption Restart Procedure; No need to
pause rx for slave role on reception of PAUSE_ENC_RSP PDU as
its already paused.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit adds http_client_set_net_pkt_pool() function that allows
caller to define net_buf pool that is used when sending a TCP packet.
This is needed for those technologies like Bluetooth or 802.15.4 which
compress the IPv6 header during send.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For IPv6 header compressed packet, the IP header offsets will
be wrong. In this case there is no need to print error when
trying to print TCP packet information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds http_server_set_net_pkt_pool() function that allows
caller to define net_buf pool that is used when sending a TCP packet.
This is needed for those technologies like Bluetooth or 802.15.4 which
compress the IPv6 header during send.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The buf variable may have been unrefed by net_buf_frag_del thus it shall
not be used to store the sent data nor it should be in the
chan->tx_queue.
Jira: ZEP-2395
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix assert in the controller on master connection creation
due to the CONNECT_IND PDU being transmitted beyond the
calculated scan window.
This is related to commit 80a796b493 ("Bluetooth:
controller: Fix scanner to use correct slot ticks")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix an assert in next role event preparation when a
connection terminated during the connection event being
aborted/pre-empted out by the next role event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
CONFIG_MQTT_LIB_TLS is introduced to enable TLS support.
Also, prj_frdm_k64f_tls.conf is added to demostrate the whole idea.
jira:ZEP-2261
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Use net app API since we want to enable MQTT with TLS.
mqtt_connect() and mqtt_close() are added to build and close the
connection to the broker. The caller doesn't need to deal with
the net context anymore and the most of network setup code in
mqtt_publisher is removed.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
As SLIP TAP is now the default after the commit ca0ad13a61
("net: enable SLIP only on QEMU targets"), clarify the comments
and settings in various Kconfig files that talk about slip.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If the network interface is down, then IPv6 DAD (Duplicate
Address Detection) cannot be done if new IPv6 address is added
to the network interface. This can happen in Bluetooth, where
network interface is taken up only after there is a BT connection.
The DAD is delayed and done later after the network interface is up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Normally network interface is always UP, but Bluetooth
interfaces are down until connected. So if this is the case,
then check the interface status before trying to access variables
that are NULL. This was seen with "net iface" shell command when
BT was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In case the application is using NET_L2_BLUETOOTH the SLIP drivr shall
not be selected as bus they cannot coexist since they use the same UART
port:
arch/x86/soc/ia32/Kconfig.defconfig:
config BLUETOOTH_UART_ON_DEV_NAME
default "UART_1"
config UART_PIPE_ON_DEV_NAME
default "UART_1"
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
* Fix the indentation which was caused by uint32_t -> u8_t changes.
* Make sure there is no unused variable warning if debugging is
enabled but debug level is low.
* Add assert that checks that Imax_abs is > 0 which it should be.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there are no neighbors or there is no route to one specific
neighbor, then check the NULL pointer before accessing the route.
This issue was seen with "net route" shell command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Since we generate BLUETOOTH_MONITOR_ON_DEV_NAME based on dts we need a
!HAS_DTS check around it. Otherwise we can get into odd build errors.
Its also possibly that we don't specify "zephyr,bt-mon-uart" and in that
case we default to CONFIG_UART_CONSOLE_ON_DEV_NAME (ie 'zephyr,console'
on DTS platforms).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If IEEE 802.15.4 is enabled, then setup the network settings
automatically so that the device is ready for IP configuration.
This is only done if CONFIG_NET_APP_AUTO_INIT is enabled, which
is currently the default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add an initial implementation for the Bluetooth Mesh Profile
Specification. The main code resides in subsys/bluetooth/host/mesh and
the public API can be found in include/bluetooth/mesh.h. There are a
couple of samples provided as well under samples/bluetooth and
tests/bluetooth.
The implementation covers all layers of the Bluetooth Mesh stack and
most optional features as well. The following is a list of some of
these features and the c-files where the implementation can be found:
- GATT & Advertising bearers (proxy.c & adv.c)
- Network Layer (net.c)
- Lower and Upper Transport Layers (transport.c)
- Access Layer (access.c)
- Foundation Models, Server role (health.c & cfg.c)
- Both PB-ADV and PB-GATT based provisioning (prov.c)
- Low Power Node support (lpn.c)
- Relay support (net.c)
- GATT Proxy (proxy.c)
Notable features that are *not* part of the implementation:
- Friend support (initial bits are in place in friend.c)
- Provisioner support (low-value for typical Zephyr devices)
- GATT Client (low-value for typical Zephyr devices)
Jira: ZEP-2360
Change-Id: Ic773113dbfd84878ff8cee7fe2bb948f0ace19ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The address lifetime timer was cancelled always even if the address
timer was never installed.
Jira: ZEP-2397
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
poll() allows to (efficiently) wait for available data on sockets,
and is essential operation for working with non-blocking sockets.
This is initial, very basic implementation, effectively supporting
just POLLIN operation. (POLLOUT implementation is dummy - it's
assumed that socket is always writable, as there's currently no
reasonable way to test that.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Use net_context_put(), not net_context_unref(). This makes sure
that after sending response, connections are properly closed.
Jira: ZEP-2362
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Introduce net_context_bind_default() to ensure that local address is
set for context if not yet (via explict bind() call). This fixes
dereferences of NULL pointer to local address which was exposed when
MMU was enabled for qemu_x86.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When populating the hardware filter, add only slots that are marked as
taken to avoid the hardware being confused by all-0 addresses. This
solves an EBQ issue with whitelist filtering.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To avoid warnings (seen on some machines) that a function reaches its
end without returning a value, conditionally compile the function in a
way that this cannot happen.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix master terminate procedure so that if slave responded to
the ack from master for the LL_TERMINATE_IND then the master
correctly disconnected.
This fixes TP/CON/MAS/BV-09-C [Master Accepting Termination]
in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Tested-by: Ulrich Myhre <ulmy@nordicsemi.no>
Fix implementation to maintain a connection in the slave
role not taking slave latency into use before receiving an
acknowledgement from the master.
This fixes TP/CON/ADV/BV-03-C [Master Missing Slave Packets]
in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Tested-by: Ulrich Myhre <ulmy@nordicsemi.no>
According to RFC7959 page 30, "The end of a block-wise transfer is
governed by the M bits in the Block options, _not_ by exhausting the
size estimates exchanges."
Therefore, we should check the M bit instead of total size (which
is not always available, too)
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When the controller is configured to have its worker and job
be run at different interrupt priority, check for mayfly
priority being equal was incorrect.
Fixed by conditionally compiling the correct check of mayfly
priority level.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed a defect wherein anchor for first scanner event was in
the past (when looking for a free timeslice to avoid
overlapping with master role events) when actually there
were no master roles active. This defect caused the scanner
role to assert, when started with other roles active (eg.
advertiser), when trying to catch-up to current tick.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 3c23c6f53d ("Bluetooth: controller:
Fix assert due to stale tick count") as this leads to
connection events to be skipped, failing conformance tests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit b5235207d3 ("Bluetooth: controller:
Fix for scanner Rx window hang") as this leads to
connection events to be skipped, failing conformance tests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If either UDP or TCP is enabled but not both, then connectivity
fails. This was a side effect of commit 3604c391e ("net: udp:
Remove NET_UDP_HDR() macro and direct access to net_buf")
Jira: ZEP-2380
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When IPv6 fragments were sent, the last IPv6 fragmented packet
was accessing NULL pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix calculation of T_Terminate and other procedure timers by
using ceil on calculated connection interval units.
This fixes TP/CON/MAS/BI-02-C [Master T_Terminate Timer] and
TP/CON/SLA/BI-02-C [Slave T_Terminate Timer] in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Ulrich Solli Myhre <ulmy@nordicsemi.no>
Fix implementation so that both slave and master behave same
during connection setup and generate disconnection complete
with reason 0x3e (connection failed to be established).
This fixes TP/CON/ADV/BV-02-C [Accepting Connections
Timeout] in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Ulrich Solli Myhre <ulmy@nordicsemi.no>
Whenever not using the whitelist the resolving list is traversed to
verify that the device is allowed depending on its current privacy mode.
In the case where the device is not found by address in the resolving
list, allow the request to go through, since we are then dealing with an
unknown devices and the resolving list restrictions do not apply.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This causes num of packets command handling to dead lock since it
is done on RX buffer destroy if used on TX it may not be destroyed
on time causing.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The specification states that the AdvA in a Scan Request packet should
be identical to the one sent in the original advertising packet, so
check this when processing a Scan Request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When the initiator is using an RPA and we match it using the filtering,
we should return early and allow the device packet through instead of
going through the whole resolving list.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The specification states that filter policies shall be ignored for
directed advertising, so reflect this behaviour in the code.
Additionally when the local device is using RPAs but the peer uses an
identity address, the resolving list index needs to be updated when
traversing the RL to reflect that there has indeed been a device match
even though the IRK match did not happen.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The AdvA in the CONN_IND packet must match the AdvA in the advertising
packet that triggered it regardless of the advertising type.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added BUILD_ASSERT check for Tx and Rx thread priorities.
The Tx thread priority shall be higher than Rx thread
priority in order to correctly detect transaction violations
in ATT and SMP protocols. The Number of Completed Packets
for a connection shall be processed before any new data is
received and processed for that connection.
The Controller's priority receive thread priority shall be
higher than the Host's Tx and the Controller's Rx thread
priority.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When the ARP message is received when the device is starting up,
the network interface might not yet have IPv4 address setup
correctly. In this case, the IP address pointer could be NULL
and we must not use it for anything.
Fixes#752
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Coverity reported false positives, add comment about these in
the code.
Jira: ZEP-2344
Jira: ZEP-2345
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch fixes a regression which the original patch introducing
this code (improving concurrent connection handling) had on
*sequential* connection handling. Without this patch, with the
default CONFIG_NET_TCP_BACKLOG_SIZE of 1, after each connection
request, there was 1s (ACK timeout) "dead time" during which new
connection wasn't ptocessed.
This is because k_delayed_work_remaining_get() was checked the
wrong way. But there's no need to use k_delayed_work_remaining_get()
at all, instead just call k_delayed_work_cancel() and dispatch on
its return code.
Note that there's still a problem of synchronizing access to
the global array tcp_backlog, as worker (which modifies it) may
preempt packet handling code (which also modifies it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The sequence number validator was checking the seq numbers
incorrectly. This caused some valid RST packets to be dropped
and the TCP stream to hang.
Added also a TCP test case that tests the seq validator.
Jira: ZEP-2289
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Usually it is not enough to have just one IPv6 multicast
address defined for the network interface. So allocate three
IPv6 multicast addresses for the network interface as IPv6
by default uses multicast a lot. This hopefully will avoid
some mysterious errors if the addresses run out.
Note that this will increase memory usage a bit so you might
need to lower the count in your conf file if memory is low.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 210c30805b ("net: context: Close connection fast
if TIME_WAIT support is off") was not a proper way of closing
the connection. So if Zephyr closes the connection (active close),
then send FIN and install a timer that makes sure that if the peer
FIN + ACK is lost, we close the connection properly after a timeout.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 00ac0487b0 ("net: context: Remove tcp struct SYN-ACK
timer handling") removed also the passive close ACK timer.
Adding that ACK timer back so that we can close the connection
properly even if the last ACK from peer is lost.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds a second vendor service testing if service changed indications
works with more than one change in a row and as a bonus it implements
echo attribute which notifies any data that is written to it:
> ACL Data TX: Handle 3585 flags 0x00 dlen 9
ATT: Write Command (0x52) len 4
Handle: 0x0013
Data: 0000
< ACL Data RX: Handle 3585 flags 0x02 dlen 9
ATT: Handle Value Notification (0x1b) len 4
Handle: 0x0013
Data: 0000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
With introduction of bt_gatt_service_unregister it is now possible to
unregister service at runtime.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There could be situations where many services are changed in a row which
would cause k_sem_take to block on the second change, but if the calling
thread is actually the RX thread then this will deadlock since the RX
thread is the one processing the confirmations of indications and it is
blocked k_sem_give is never called.
To solve this the services changes are now offloaded to the system wq
and the code will attempt to consolidate the range being changed so only
one indication is send. If for some reason another changes is caused
while confirmation is pending we just reschedule it to run later to
avoid blocking the system wq in the same way.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For consistency with the Resolving List, rename the whitelist filter to
match its type and the privacy-enabled version to align it with the
short name used in the RL.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To correctly handle the allocation and deallocation of resolving list
items, the ll_rl_find and wl_pees_find functions have been modified to
return an invalid index instead of a negative value in case of error.
This is to avoid the ambiguity when mixing indices and negative numbers,
which does not play well with the first index 0.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This fixes coverity CID 171565 which may be valid in case of the
connection is not properly setup, or its memory is corrupted, it
may cause use of invalid addresses to be set using
net_if_set_link_addr.
JIRA: ZEP-2344
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the TCP data packet needs to be re-sent after the packet is lost,
then the acknowledgment number will be changed. This then means that
the TCP checksum needs to be recalculated too.
Signed-off-by: june li <junelizh@foxmail.com>
When a node receives consistent DIO messages with same data from
Border Router just ignore those messages. Need not to proceed
further.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Link metric is part IPv6 neighbour data struct. But RPL code is
trying to access it from RPL parent table where link metric doesn't
exist. So provided an api to get IPv6 neighbour data from RPL parent
data.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
DAG rank will be properly written with net_pkt_write_be16() in
network packet. API will take care of endianness. So need
not to convert it using htons().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Sender rank (16 bit uint) was properly read with net_frag_read_be16()
api and need not to convert it again using ntohs().
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We had various asserts when checking network packet length but
printed also error when there was none. Fix this by checking
do we really have a too short message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_TCP_HDR() macro as we cannot safely access TCP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the TCP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove NET_ICMP_HDR() macro as we cannot safely access ICMP header
via it if the network packet header spans over multiple net_buf
fragments.
Jira: ZEP-2306
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 HBH option PAD1 ext header was not parsed properly
as the code read one extra byte from the ext header. The
PAD1 length is only 1 byte.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add utility function that helps to figure out if the
protocol headers can be directly accessed when they fit one
net_buf fragment, or if they need to accessed using various
net_pkt helpers that know about reading data from two
different net_buf's.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of directly setting pointer to where to start to calculate
the various IP related checksums, use the net_frag_skip() to first
find out what is the fragment where the calculation should start.
This needs to be like this so that if the IP header + possible
extension are so long that they do not fit the first fragment,
we need to be prepared to look into second fragment.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The following error and warning is received when connecting
to certain central devices:
[bt] [ERR] hci_num_completed_packets: packets count mismatch
[bt] [WRN] bt_att_recv: Ignoring unexpected request
This could happen if Tx-ed packet is not added to pending
list before a num of completed packets event and/or new Rx
packet is received.
This is fixed by reducing the Rx thread priorities in the
Host and the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_context_unref() is protocol agnostic, after being un-referenced,
the same context might end up being used then for UDP,
if context->tcp is not reset to NULL, calling net_context_unref()
after this UDP usage will again try to release this TCP pointer
which might lead to random error.
Signed-off-by: june li <junelizh@foxmail.com>
The code in send_frag() depends on being able to allocate a new
pending tx contexts with 100% certainty. We must therefore notify
*all* connections instead of the current one in order to ensure that
there are free contexts available in free_tx.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases the lladdr might not be set, currently this is
seen with RPL unit tests, in which case we must not access
the lladdr.
Jira: ZEP-2330
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is no route to the neighbor, then do not try to delete
it because the route pointer is NULL.
Jira: ZEP-2329
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move a way from misc/ and put in its own subsystem to allow enhancements
in the future and make it a core part of Zephyr, not just something
misc.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The num_handles parameter of the Number Of Completed Packets event is
8-bits and not 16-bits, so no helper variable or byte order conversion
is needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case both conn->tx_notify and conn->tx_queue have data in them we
should first process the notify queue and only then new outgoing
packets.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Due to the missing remainder support in the ticker_start
function for first interval, fix implementation so as to
round the first interval/offset during master connection
setup and connection update to within +/-16us.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The SYN-ACK timer is now handled by the TCP backlog functionality,
while the remaining ACKs for established connections use the tcp
struct ack timer. With this, code setting tcp struct SYN-ACK state
timers can now be removed.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add timer for sent TCP SYN-ACKs. If the timer is already
scheduled to run before canceling it is attempted, set
the cancelled flag and let the callback remove the
delayed work.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Add an array of configurable size that holds TCP backlog entries.
The array is shared between all incoming TCP connections in order
to make it possible to get away with less memory consumed than
with a connection based approach.
The backlog entries are created when a SYN is received for a
listening TCP socket and removed once the corresponding ACK is
seen. With an incoming RST the corresponding backlog entry is
cleared, if any.
The size of the global backlog array is defined with the
CONFIG_NET_TCP_BACKLOG_SIZE Kconfig variable.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The worst-case maximum number of CCC entries we need is actually
MAX_CONN + MAX_PAIRED. Provide a helper define for it and use it
whenever appropriate.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI Read Remote Version Information Complete event structure was
incorrect, leading to qualification test failures. This patch fixes the
structure and also the storing of the data in an endianness-agnostic
manner.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To avoid manipulation of the irkmatch_ok and irkmatch_id, rely instead
on Resolving List indices for all checks in the advertising ISR.
Although we do incur in a small overhead to look it up initially, the
overall gains are worth the change.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The Controller reserved more than required time for
advertisement event length. Due to this, directed
advertisements did not meet the required <= 3.75ms
interval. It is now fixed by having event lengths based
on the advertisement PDU types.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Correct the default value (0x0) for the Event Mask Page 2 and add the
command to set it to the list of supported commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When neither IPv4 nor IPv6 are selected the limit that is
passed to k_sem_init will end up being 0, which will trigger
the folowing assertion in k_sem_init;
__ASSERT(limit != 0, "limit cannot be zero");
Fixed by not passing count as initial and limit value but
only as initial value and use UINT_MAX as limit.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Correctly filter out the Authenticated Payload Timeout Expired event
based on the bit present on page 2 of the Event Mask.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to be able to filter events present in Page 2 of the Event
Mask, this command allows the Host to set the Page 2 of the bitmask
through the corresponding command.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Reset and initialize filters correctly based on whether privacy is
enabled in the controller. Particularly relevant in the case of the
whitelist, which is handled in a completely different way if privacy is
enabled. Additionally reset the peer IRK list in the resolving list
whenever the list itself is cleared.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When flashing in synchronous mode with BLE roles active,
ticker function calls will be deferred to avoid radio ISR
latencies. Increase the total operations supported by 1, to
accommodate flash driver's use of ticker operations.
It has been observed, without this increase, either the
flash driver returned -ECANCEL or the BLE Controller
asserted on data transmit as a slave (trying to force data
transmit on earliest connection event interval).
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Locking interrupts for a long duration is in general bad design, and
is particularly bad for the controller which depends on low latency
interrupts. Instead of using interrupt locking introduce a new flag to
track the shared buffer usage and simply drop characters if the flag
is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Implement privacy-enabled filtering in the advertiser role. This
includes all required checks when running address generation and
resolution so that the advertiser complies with the relevant
specification sections.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix missing re-initialization of ret_cb to
TICKER_STATUS_BUSY before every new call to ticker interface
functions' with operation's callback.
One issue was undirected advertisement disable to return
failure status in the scan_adv sample.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
With the fix in commit 3c23c6f53d ("Bluetooth: controller:
Fix assert due to stale tick count") it is required that a
skipping event shall abort the previous role in order to
enable the ticker_job to resume and reschedule next ticker
expiry.
In the scan_adv sample, with continuous scanning, an
advertiser would pre-empt it, but if the advertiser skipped
its event without aborting the scanner, the scanner is hung
with its rx window without a timeout, and HCI command to
stop the advertiser will wait forever to complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The scanner was reserving a little less slot ticks which
caused other roles to overlap before scan window could
close.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The network application API is a higher level API for creating
client and server type applications. Instead of applications
dealing with low level details, the network application API
provides services that most of the applications can use directly.
This commit removes the internal net_sample_*() API and converts
the existing users of it to use the new net_app API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This doesn't make much practical difference, however it should resolve
Coverity CIDs 170740 and 170748.
Jira: ZEP-2343
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If ICMP packets do not fit in 1 net_pkt fragment the checksum
will be calculated incorrectly.
The problem shows up when using ping with the -s option to
create large ping requests. Eventhough the ping command does
accept the reply without complaining, Wireshark warns that
the icmp checksum is incorrect.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
With the ticker for flash driver added, the Controller was
corrupting memory outside its allocations by incorrectly
using the flash ticker instance to be a BLE role and
corrupting memory. This is now fixed by checking for the
ticker ids to be within the Controller's use before using
them.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In some cases applications may want better control of advertising
instead of the stack doing automated re-enablement. Introduce a new
option that can be used to do more "manual" advertising control.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BT_DEV_ADVERTISING flag already does a suffient job with tracking
the actual advertising state, so there's no need for bt_le_adv_stop()
to return an error if KEEP_ADVERTISING is set. We still need to clear
KEEP_ADVERTISING, but it should not be considered an error if it was
not set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed uninitialised auto variables, that had caused compile
errors under CONFIG_DEBUG=y.
Jira: Zep-2334
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If a socket is closed without reading all data from peer or accepting
all pending connection, they will be leaked. So, flush queues
explicitly.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
With CONFIG_NET_SOCKETS_POSIX_NAMES=y, "raw" POSIX names like
socket(), recv(), close() will be exposed (using macro defines).
The close() is the biggest culprit here, because in POSIX it
applies to any file descriptor, but in this implementation -
only to sockets.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This adds Kconfig and build infrastructure and implements
zsock_socket() and zsock_close() functions.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Temporarily, disable scan request notification reports when
LE Advertising Extensions feature is enabled; as support for
enabling scan request notification is not yet added to the
Controller's Link Layer interface functions, yet.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Intention is to test flash driver along with BLE radio.
Added flash shell module with commands for erase, write-check, read and
co-operation with radio stress test.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Extend radio ticker nodes for support in-timeslice execution
Added interface for abort the radio
Added interface for check whether the radio is idle
Added interface for get ticker IDs for timeslice ticker node
Added interface for check whether radio ticker is running
Added interface for check whether radio ticker is initialized
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
In order to associate a hit on the hardware IRK filtering with an entry
of the resolving list, add an array of correspondance between the IRKs
and the resolving list entries.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order for some of the required checks in the ISR to be performed, we
need to keep track of which of the items in the resolving list are in
the whitelist as well. Track them using a single bit in the resolving
list entries.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to obtain the ID (index) of the device matched in a hardware
filter, a new API call has been added along with the required
implementation for nRF5x devices.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When force scheduling a ticker use the number of times the
tickers have already skipped their intervals to decide if
the forced ticker can pre-empt the colliding ticker. This
introduces a fairness amongst tickers contesting for the
overlapping time slice.
Flashing in co-operation with Radio needs to be fair in
order to avoid connection supervision timeouts.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation towards mesh advertise implementation, avoid
one-shot tickers with slots, that have been scheduled to
expire, from being removed by a forced start or update
operation on another ticker.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The global mbedtls heap is set automatically now so no need to
set it individually in the http library.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move the PRNG initialization after reading local supported commands,
so that we don't send HCI_LE_Rand if the controller doesn't support it
(we still need to fail the init however). The patch also removes a few
unnecessary #ifdefs related to crypto.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid iterating twice through the list, have ll_rl_find() return the
first free empty slot on the list.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add handling of the LE Set Privacy Mode HCI Command along with the logic
required to take it into account when populating the hardware filters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order for privacy to work correctly with and without peer IRKs, an
additional hardware filter is required to help match the peer device in
the case address resolution is not possible for a peer since the Host
has not provided a peer IRK for it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When removing a device from the resolving list, if it contained a peer
IRK then it is necessary to update the indices that point to the peer
IRK list, since the list itself is contiguous in memory.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When using privacy, an additional cache of the actual privacy peers is
required to avoid additional processing in the ISR (since some of the
peers in the whitelist will be disabled by the corresponding privacy
settings). Add the cache and populate the actual whitelist just before
advertising, scanning or initiating a connection.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Properly use the role and feature Kconfig variables to populate both the
supported commands and the supported states in the controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the peripheral role depends on the broadcaster one, and the
central role depends on the observer one, select them automatically
instead of using defaults.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Three response codes are missed in zoap_header_get_code() which will
result in the response code returned from the function being set as
ZOAP_CODE_EMPTY. Check include/net/zoap.h for the missing code
definition.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
It's possible that the controller will emit the number of completed
packets event before bt_send() returns, or possibly preempt
send_frag() before it manages to call add_pending_tx(). We have to
therefore add the pending TX entry before calling bt_send().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed assert due to stale tick count in role event
preparation. This happens when ticker timeout expiry is
delayed from the requested realtime anchor, due to thread
mode processing overheads and occurring interrupts therein,
if any, that added a delay between requested anchor tick
and actual scheduling for the requested ticker timeout.
The assert is reproduced in bt shell by starting advertising
and following it with continuous scanning (interval 2.5ms,
window 2.5ms), on nRF51x. If the overheads and/or a
advertiser event delayed the scheduling of scanner by over
2.5ms, then the preparation of scanner asserted.
The assert has been fixed by checking for stale tick count
at expiry in role event preparation and skip the event
gracefully.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For whitelist and resolving list handling, avoid trying to start the
advertiser and scanner roles when they are already running.
Additionally, and since simultaneous scanning and initiating is not
supported, correctly report this to the host both in the supported
states and in the HCI command via an error code, instead of silently
disabling scanning.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
We have conflicting types between the decleration and implementation of
several radio functions. We should be using u32_t everywhere. This
shows up when we try and build with newlib enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added HAL Radio abstractions to use SoC specific Radio Timings
as documented in SoC's electrical characteristics.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In LISTEN state ignore a TCP RST. In SYN RCVD state, reset TCP
connection state to LISTEN when a valid RST segment is received. In all
other states close the connection - except that these other states will
not be handled in tcp_syn_rcvd() function.
Jira: ZEP-2279
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
An OCF is a 10-bit value as defined by HCI, and therefore requires a
16-bit integer to store it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixed assert due to incorrect implementation of stopping of
advertiser role under directed advertisement timeout, and
also, fixed assert due to adv stop ticker not being stopped
on advertisement disable from thread mode.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added checks for advertiser and initiator/target addresses
received in CONNECT_IND when performing directed
advertising.
This is required to pass TP/CON/ADV/BV-04-C [Directed
Advertising Connection].
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When directed advertisements timed out, connection context
associated was not being released. Subsequent connectable
advertising or connection creation failed.
This is now fixed by releasing the connection context on
directed advertisement timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If the CONFIG_NET_TCP_TIME_WAIT support is disabled, then do not
start to wait for reply to sent FIN in active close, but unref
the corresponding net_context in order to close the connection
as soon as possible.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor whitelist handling into generic filter management in
preparation for future resolving list ID address filters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename bt_gatt_unregister_service to bt_gatt_service_unregister to be
consistent with other APIs such as bt_gatt_service_register.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This initial commit adds the following:
* Handling of privacy HCI commands
* New Link Layer filter module for both whitelist and resolving list
* Advertising RPA generation with timeouts
Follow-up commits will expand the functionality.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Enforce the logical dependency between SMP, RPA generation and privacy
in the Kconfig files for the Bluetooth subsysem.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For consistency with the return value and to conform with other naming
schemes, rename mem_is_zero() to mem_nz().
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This is unmaintained and currently has no known users. It was
added to support a Wind River project. If in the future we need it
again, we should re-introduce it with an exception-based mechanism
for catching out-of-bounds memory queries from the debugger.
The mem_safe subsystem is also removed, it is only used by the
GDB server. If its functionality is needed in the future, it
shoudl be replaced with an exception-based mechanism.
The _image_{ram, rom, text}_{start, end} linker variables have
been left in place, they will be re-purposed and expanded to
support memory protection.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Use globally available find_lsb_set in Zephyr instead of a
custom find first set function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Moving the net_buf_pool objects to a dedicated area lets us access
them by array offset into this area instead of directly by pointer.
This helps reduce the size of net_buf objects by 4 bytes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The net_pkt_split() was incorrectly checking fragA pointer
even before it was allocated.
The unit test is fixed and converted to ztest.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
gatt-unregister-service can be used to remove the test service at
runtime causing service changed to be indicated:
00:1b:dc:07:31:88 (public)> gatt-unregister-service
[bt] [DBG] gatt_indicate: (0x0011e100) conn 0x0011d880 handle 0x0008
[bt] [DBG] bt_att_req_send: (0x0011e100) conn 0x0011d880 req 0x0011db00
[bt] [DBG] att_send_req: (0x0011e100) req 0x0011db00
Unregistering test vendor service
< ACL Data TX: Handle 3585 flags 0x00 dlen 11
ATT: Handle Value Indication (0x1d) len 6
Handle: 0x0008
Data: 0a001000
> ACL Data RX: Handle 3585 flags 0x02 dlen 5
ATT: Handle Value Confirmation (0x1e) len 0
Jira: ZEP-2225
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
With the introduction of Service Changed support it is now possible to
unregister services at runtime.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds bt_gatt_register_service using bt_gatt_service which contains
the attribute array that is then added to the database saving a pointer
in each and every attribute declared.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GATT is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GAP is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes applications able to select the value used for the
GAP appearance attribute.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Removes CONFIG_BLUETOOTH_GATT_DYNAMIC_DB in preparation to the
introduction of bt_gatt_unregister.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In certain cases a response may happen even before number of complete
packets is generated by the controller:
[bt] [DBG] att_req_destroy: (0x0011cfe0) req 0x0011daa0
[bt] [DBG] att_process: (0x0011cfe0)
[bt] [DBG] att_req_sent: (0x0011d780) conn 0x0011d820 att 0x0011d9a0
att->req 0x00000000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In preparation towards Privacy 1.2, move implementation that
swapped scan response PDU double buffer to same place as
where adv data PDU double buffer is swapped. So that, change
in AdvA in adv data PDU can be reflected in scan response
PDU buffer.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added fix to avoid adv data set function call from
corrupting a ADV_EXT_IND PDU under LE Extended Advertising.
Also, avoid redundant code execution under directed
advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Only ADV_IND, ADV_DIRECT_IND, and CONNECT_IND PDUs can have
ChSel bit set in Advertising channel.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Bluetooth subsystem assumes execution of its system threads in
cooperative priority, including the system workqueue and the thread
that interact with the controller (i.e. calling bt_send). This commit
adds a compile-time check for the system workqueue priority and
documentation for the bt_send API call.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixed compile error due to the missing header file
dependency on bluetooth/hci.h, for bt_addr_le_t, in the
Link Layer header file.
Merge of PR #475 introduced the new dependency that broke
compilation after merge of #474.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added a callback function ll_adv_scan_state_cb from the
Controller that gets called on either an advertiser or a
scanner getting started as the Controller's first enabled
state. The callback is also called on the Controller's
last disabled advertising or scanning state.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing implementation to reset the advertiser state
when directed advertisements stop without a connection being
established.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Bluetooth Link Layer LE Advertising Extensions commands
for manual testing the feature during development. First one
being advx command to start non-connectable non-scannable
extended advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In order to reuse code, the reset() function is used both to handle the
reset HCI command but also to initialize the internal HCI variables when
bringing up the system. In the latter case, avoid setting the reset bit
in the state atomic and signalling the polling API, since that is not
required during initialization.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As a preparation for advanced filtering (Controller-based privacy) this
commit refactors whitelisting so that it becomes its own module and
actually correctly performs state tracking to avoid modifying the
whitelist when it's in use.
Additionally it also removes the duplicate separate entries for
advertising and scanning, since the specification only allows one single
global whitelist singleton.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add internal functions to read advertiser and scanner filter
policy if the roles are enabled. This is required to
restrict updates to whitelist and resolving lists when
filter policy are being used by the roles.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Under invalid host behavior, trying to start advertising
while already active would corrupt the advertiser context.
This is fixed by having an explicit flag to check whether
advertiser is already running.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Under invalid host behavior, trying to start scanning while
already active would corrupt the scanner context. This is
fixed by having an explicit flag to check whether scanner is
already running.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
From
http://pubs.opengroup.org/onlinepubs/7908799/xns/netinetin.h.html:
in_addr_t
An unsigned integral type of exactly 32 bits.
[] the in_addr structure [] includes at least the following member:
in_addr_t s_addr
In other words, POSIX requires s_addr to be a single integer value,
whereas Zephyr defines it as an array, and then access as s_addr[0]
everywhere. Fix that by following POSIX definition, which helps to
port existing apps to Zephyr.
Jira: ZEP-2264
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If we receive a HTTP request and if the earlier context is still
active and it is not the same as the new one, then close the earlier
one. Otherwise it is possible that the old context will be left into
TCP ESTABLISHED state and would never be released. Example of this
is that we had IPv4 connection active and then IPv6 connection is
established, in this case we will disconnect the IPv4 connection
after this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Given that K_NO_WAIT is passed as a timeout to net_context_recv(), it's
unlikely this function will return any error value. It's cheap to
check, though, so do it.
Coverity-CID: 170580
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The shell takes care of removing the module name so it is no longer
necessary to have this adjustment.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The command callback might not recognize commands if the input comes
with the module name as first parameter as both argc and argv will be
off by one.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the command cannot be execute code should return a proper since this
may not be a user input.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds shell_exec which can be used to execute commands directly
without the use of a console which is useful for both testing as well
as interfacing with applications/upper layer which would like to have
access to shell commands directly.
In addition to that this may be more trivial to interface with instead
of using fifos like uart_register_input and telnet_register_input do.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In certain TCP states we should not try to send RESET segment
to peer. So check this and do not try to use NULL pkt to send
a message.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net http monitor" command turns on HTTP monitoring,
which means that for each incoming HTTP or HTTPS request,
a information about source and destination address, and
the HTTP request URL is printed.
User can disable the monitoring by "net http" command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_NET_DEBUG_HTTP_CONN is enabled, then start to collect
currently active HTTP connections to HTTP server.
This is only useful for debugging the HTTP connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Restrict encryption support on nRF51 series SoC to Bluetooth
LE 1M PHY and max. 27 bytes PDU. If 251 bytes PDU using Data
Length Update procedure is desired, then LE Encryption
procedure will not be supported (until a software CCM is
implemented in future).
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Kconfig option to be able to conditional compile the
Bluetooth v4.0 LE Encryption procedure.
This is needed in order to be able to not support encryption
on nRF51 series when using Data Length Update procedure with
upto 251 byte payloads until a software-based CCM support is
implemented.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If we cannot send network data, then print the error code when
printing debug information about the issue. This is needed when
debugging the issue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add HTTPS support into http-client library. The init of the
HTTPS client connection is different compared to HTTP client,
but the actual HTTP request sending is using the same API as
HTTP client.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is done so that both http_client and http_server functionality
can share the same heap.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When src and dst addresses are compressed based on context
information, uncompression method should verify CID bit,
SAC and DAC bits and context ID's. But it has missed some
cases which resulted in invalid uncompressed IPv6 header.
e.g. CID is set, SAC is 0 and DAC is 1 and context id's provided.
Uncompression method assumed that src address is compressed based
on context information but it is not.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Empty RPL HBH header will be inserted while finalizing IPv6 packet
but updated after finding nexthop and sent the packet. In case of
Bluetooth or multicast dst address it was missed. Resulted in
empty RPL HBH header and packet dropped at peer node. It should
be updated in all circumstances.
Jira: ZEP-2088
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The mbedtls debugging function was set before the ssl config
struct was initialized. This meant that it was not possible
to activate mbedtls debug prints. This commit sets the debug
print option after the config struct has been initialized.
Fixed also the debug prints which print extra \n which looks
very bad in debugging outputs.
This commit does not enable mbedtls debugging, it just makes it
possible to output mbedtls debug prints. In order to get mbedlts
debug prints one needs to do this:
* set DEBUG_THRESHOLD to >0 in http_server.c
* enable CONFIG_NET_DEBUG_HTTP in project config file
* enable MBEDTLS_DEBUG_C in mbedtls config file (see file pointed
by CONFIG_MBEDTLS_CFG_FILE option)
* in qemu, one needs to increase the size of the available RAM,
this setting does the trick, CONFIG_RAM_SIZE=300
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Semantics of ENOENT error as used previously is "named entity not
found", whereas for "I/O handle is not valid", there's EBADF. For
example, POSIX/SUSV2 doesn't even list ENOENT as a possible error
for accept(), connect(), recv(), etc. whereas it lists EBADF, e.g.:
http://pubs.opengroup.org/onlinepubs/7908799/xns/connect.html
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add a repeat param to gatt-write-without-response so that
it covers what gatt-write-without-response-repeated was
doing. gatt-write-without-response was removed in the
commit 26eae70da.
gatt-write-signed too will have repeat param with this
change.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
At the moment all bluetooth logs are prefixed with [bt] making it
difficult to understand where the logs belong to.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Instead of waiting forever for a free net_buf, set a timeout to
the allocations (500 ms). This way the application will not be
blocked by memory exhaustion.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In some cases the net_pkt can be null when freeing it,
this will print error from net_pkt library. Avoid this by
checking the value of net_pkt before calling net_pkt_unref().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we re-connect to same peer server, then we should select a new
source port. Noticed that if the same source port as before is
used for the new connection, the peer might drop the packet. This
was seen when connecting to Linux peer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Defines a new tunable, CONFIG_NET_TCP_RETRY_COUNT, that determines the
number of segment retransmissions that the IP stack will attempt to
perform before resetting the connection.
The default value is 9 retransmissions, which amounts to 1:42 minutes,
as close as possible to the minimum recommended by RFC1122.
Jira: ZEP-1956, ZEP-1957
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
It's mandatory to set chan->ops so explicit checks for it are
redundant. What's worse, inconsistent checking for this triggers
static code analyzer warnings. This patch fixes Coverity CID 151984.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
buf->len should be validated before accessing it since remote can
send invalid frame_len which can result in out of bound memory
access.
This also fix the len check wrt cstate, since current check is
not considering the cstate length size and frame_len size.
Jira: ZEP-2110
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Added shell module for the Bluetooth Controller's ticker
interfaces.
For now, info command enumerates active tickers' details.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If we receive unknown option in neighbor advertisement message,
then skip those properly. Old code did not check the length of
the extension options which could cause infinite loop.
Jira: ZEP-2219
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
If we received a bad HTTP request, then subsequent good requests
were also returning 400 error code. The parsing state needs to
be initialized after each received HTTP request.
Jira: ZEP-2181
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes the following issue:
"In expression 1UL << chan - 1U, left shifting by more than 31
bits has undefined behavior. The shift amount, chan - 1U, is
4294967295."
Coverity-CID: 167140
Jira: ZEP-2131
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
In console shell, add explicit, 'exit' command to leave the current
module. Currently this is being achieved by overloading select command
(without an argument).
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
This makes gatt-write-signed to reuse cmd_gatt_write_without_rsp since
it is quite similar and that adds the ability to send multiple octecs
instead of just a single byte.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes gatt-write-without-response-repeated and makes
gatt-write-without-response similar to gatt-write which was the
intention of gatt-write-without-response-repeated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
All the files under shell subdir shall only be build if
CONFIG_BLUETOOTH_SHELL is selected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In order to properly queue request there need to be a bt_att_req
storage but none of the calls to gatt_write_ccc were using the params
causing gatt_send to use bt_att_send and not bt_att_req_send.
To fix this now all the callers of gatt_write_ccc do set the params
properly but this means that bt_gatt_unsubscribe has to wait for it
to be completed before the application can reuse the
bt_gatt_subscribe_params.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Print also network buffers that are allocated by the IPv6
fragment handler. This is very useful in debugging.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user really wants, it is possible to increase the
maximum size of the fragmented packet. According to RFC 2460
chapter 5, we do not need to accept larger than 1500 byte IPv6
packets, so the max pkt limit is set to 2. But if really needed
the limit can be raised by defining NET_IPV6_FRAGMENTS_MAX_PKT
to some new value. Currently there is no Kconfig option for
doing this as it is unlikely that this is needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The cancellation of reassembly did not work as expected because
K_WORK_INITIALIZER() did not setup the timeout function properly.
So do the timer initialization at runtime instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IPv6 fragmentation was not working properly when the large
IPv6 packet was being sent. There is unit tests in next commit
that will test the IPv6 fragmentation sending.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the fragmented IPv6 packet was very large, we could run out
of resources. When that happened, we leaked the memory for the
pending fragments that were waiting reassembly.
Jira: ZEP-2166
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The previous default 60 seconds is way too long for our limited
amount of memory. It might be that the 5 sec is still too long
but that can be changed in the future.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
While returning 32-bit values from radio status interfaces,
explicitly compare radio h/w event registers to be non-zero,
dont just return the direct 32-bit h/w register content.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added extra assert checks to detect controller failure if
a role event preparation function was not followed by the
role event start function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Shell itself already have a help command, so instead of creating a net
specific help just fill the help description of each command.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shell modules are registered at link time thus it makes no sense to
leave it behind net_shell_init.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive unknown option in neighbor solicitation message,
then skip those properly. Old code did not check the length of
the extension options which could cause infinite loop.
Jira: ZEP-2174
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we could not split the packet properly, make sure that the
fragments that we managed to allocate are unreffed and marked
as NULL.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print also the character when hexdumping a memory area.
This is useful so that one does not need to convert hex
values to characters in head. Unprintable chars are printed
as '.'
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For some write requests, such as CCC, the code doesn't use an ATT
request context but we still need to clear the request timeout when
the response comes. Move the k_delayed_work_cancel() call to the right
place and add some debug logs that helped pinpoint this issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Both scan on and scan passive performed passive scanning,
fixed scan on command to use active scanning.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In commit c41d3edda when implementing the alternative
encryption setup implementation, the original fast
encryption setup implementation was broken. When host is
slow in responding to LTK request, the controller asserted
when fast encryption implementation is selected. This is
now fixed.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the assert in the controller during connection setup
when peer does not support CSA#2 feature and free Rx buffer
queue does not have enough buffers to generate CSA event.
The assert was reproduced by turning on advertisement
indication and scan request notification features in the
controllers advanced features, and a peer that does not
support CSA#2 initiated a connection.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Since role support is fundamental to both the Host and the Controller,
move the role configuration options to the top-level file and rename
them to fit the GAP specification, avoiding confusion between GAP and LL
names.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Only include connection-related options when CONFIG_BLUETOOTH_CONN is
selected, since otherwise this can lead to inconsistencies between
features and supported commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This replaces the use of shell_register_prompt_handler with
SHELL_REGISTER_WITH_PROMPT which doesn't overwrite other modules
prompt.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables modules to define its own prompt handler instead of always
using the default_module_prompt.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If CONFIG_BLUETOOTH_GATT_CLIENT is not defined disable command that
would depend on it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to several changes in the way stacks are calculated, 320 bytes is no
longer enough for the controller-only build. After measuring usages of
up to 320 bytes (locally) and 376 (reported by Ricardo Salveti), the
stack size is increased by 128 bytes, up to 448 bytes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The msgtype value is created using 'hdr & 3' which means that the
resulting value can never be greater than 3. This fixes Coverity CID
166771.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
No need to check attr and path variables for null as they
cannot be null.
Coverity-CID: 157595
Coverity-CID: 157602
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Added implementation to auto-update LE Data Length to max.
Tx octets supported by the local and peer controllers.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added implementation to handle an incoming Reject Ext Ind PDU in
response to a sent Length Req PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When initiating Data Length Change at the same instant the
crossover condition was not handled correctly causing the
controller to assert.
This fix will allow crossover of Data Length Update
procedure, and this collison is harmless as per Bluetooth
specification, and gracefully handled by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Return error codes for HCI Tx buffer overflow conditions are
missing which would lead to silent dropping of Tx packets if
host implementations do not follow number of completed packets
or use correct buffer counts as returned by HCI Read Buffer
Size command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Allow the caller to delay the closing of the HTTP connection
for a number of milliseconds. The purpose for this is that
the client can send still some data back to us for a short
period of time.
This is needed for example for Basic authentication so that
server is able to receive authentication values back.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since the PHY update complete event can be generated due to the
procedure being initiated by the peer, use a flag to
differentiate between local auto update initiated on connection
complete versus peer initiated anytime in the connection. This
is necessary to avoid repeated initiation of auto-update
procedures intended only to be issued on connection complete.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The address family of the UDP port listener was not set. This
caused weird debug prints in net-shell. Now the listener will
be registering IPv4 any address as it should.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a connection handler was registered, the checker function
introduced in commit 43b37cef ("Check duplicate UDP/TCP connection
handlers") did not check the address family (IPv4 or IPv6) of
the local end point properly. This caused duplicate connection
error to be returned to the caller.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The uncompressed source address in packets was not handled properly if
NET_6LO_CONTEXT was enabled.
This implementation is identical to the contextless case.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
If we do not receive last ACK when the connection is tore down,
then do not wait forever as that would eat all the resources in
the network stack. So when we enter the LAST_ACK state, we setup
a timer that will unref the connection if the last ACK is not
received.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Without change to add ACK to FIN, invalid TCP packet is generated,
where ack sequence number is non-zero. Without adjusting sequence
number as done, ACK which we send in response to peer's FIN/ACK is
not recognized by peer, and peer keeps retransmitting its FIN/ACK.
Jira: ZEP-2104
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When connection handler was unregistered, we did not remove
it from cache. This caused invalid connection to be passed to
net_context after connection unregister if connection caching
was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We did not check UDP or TCP checksum to be valid after receiving
the packet. Fix this so that the checksum is validated when
packet is received in connection handler. As the checksum validation
can be resource intensive, do it after we have verified that
there is a connection handler for this connection.
The checksum calculation can be turned OFF if needed, but it is
ON by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit "net: tcp: Handle retransmitted packets from peer"
introduced over 80 character line that was missed in review.
Fixing it now.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled RPL and STATISTICS, then enable RPL
statistics by default as that is probably what user want.
Same thing for MLD statistics.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we receive a packet with the sequence we already seen (and
processed), the most likely cause of it is that our ACK was lost,
and peer has to retransmit that packet. Then, we should just ACK
it, because otherwise peer will retransmit it again and again,
falling into exponential backoff and hosing the entire TCP
connection.
This makes changes to send_ack(), adding a flag to force sending
an ACK regardless of its cached status, and remove inline modifier,
as the function is big and called from many places.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We must check if we receive RST in any of the TCP states.
If we do not do this, then the net_context might leak as it
would never be released in some of the states. Receiving RST
in any TCP state is not described in TCP state diagram but is
described in RFC 793 which says in chapter "Reset Processing"
that system "...aborts the connection and advises the user and
goes to the CLOSED state."
We need to also validate the received RST and accept only those
TCP reset packets that contain valid sequence number.
The validate_state_transitions() function is also changed to
accept CLOSED state transition from various other states.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With the support for 2M PHY added, the controller can now Rx/Tx
upto 18/19 minimum sized L2CAP packets per 7.5ms connection
intervals.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_if_get_default() was documented as returning "Default interface
or NULL if no interfaces are configured.", but actually didn't
return NULL in the latter case. Instead, it effectively returned
a pointer to random area of memory, shared with other system
structures, so calling functions like net_if_ipv4_set_netmask(),
etc. could trash unrelated memory.
Jira: ZEP-2105
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
RFC793, "Transmission Control Protocol", defines sequence numbers
just as 32-bit numbers without a sign. It doesn't specify any adhoc
rules for comparing them, so standard modular arithmetic should be
used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
To better debug the flow of events into the Host, log the subevent code
whenever processing an LE Meta Event.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When required Rx MTU is less than configured Rx MPS, the
resultant initial credits was 0 which prevented any L2CAP
packet to be received.
Fixed by ceiling the initial credits count in the credits
calculation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Sometime it is observed on the Arduino 101 that when we write more than
4 bytes into TX USB Endpoint, first 4 bytes are getting repeated
(frequency of occurrence ~1/3000).
This patch does following :-
1. In sample application "cdc_acm", it adds capability to
handle partial transfer data incase data is transferred partially
if exceeds maximum data transfer size.
2. It restricts write of more than 4 bytes into TX USB Endpoint.
This is work around to avoid issue occarance.
Jira: ZEP-2074
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a new UDP or TCP connection handler is to be registered,
we need to check if identical handler has already been created.
If a duplicate is found, the registering call will return -EALREADY.
The earlier code did not check this but allowed two identical
handlers to be created. The latter handler was never called in
this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This helper copies desired amount of data from network packet
buffer info a user provided linear buffer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
To be consistent with other subsystem menu, use menu for
Bluetooth support in Kconfig instead of menuconfig which
showed up as checkbox.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To allow for hci_uart builds that do not include the controller code,
move the UART Kconfig option used by the sample up one level so that it
is shared by all configurations using Bluetooth:
Jira: ZEP-2132
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 698de88916 ("Bluetooth: controller:
Cleanup redundant ticker busy loop")
Scan enable asserted in ctrl.c line 3756 due to the fact that a
role event was active and ticker job has hence been disabled.
Add back the busy loop so that scan enable can wait until the
active role event completes gracefully.
The ticker busy loop is mandatory in all ticker interface calls
if a blocking behavior is desired.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The calculation in packet_rx_reserve_get() was already handled by
packet_rx_acquired_count_get(). So, let's use that code instead
and remove the duplication.
Change-Id: Ic76f70f1e78bebc74f5bef36cd92a3c332e489e9
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation can be used in packet_rx_reserve_get() where currently
the code is duplicated from packet_rx_acquired_count_get().
Let's allow use of packet_rx_acquired_count_get() regardless of whether
CONFIG_BLUETOOTH_CONTROLLER_DATA_LENGTH is enabled.
Change-Id: I613bde0a407f3caccabb22f369098575965e98ad
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During testing, lr->max_rx_octets and lr->max_tx_octets were
at times set to 0. If we use these 0 values, we end up with
very erratic behavior. Best, to check for a sane value and
if invalid, default to the value in _radio.conn_curr->max_*x_octets.
Change-Id: I57c0e3790d988f0de17993cebe5c5c2ab0fc07a6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When Controller to Host flow control is enabled, output informational
messages for certain operations to help tune and debug the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the HCI driver debug option applies to both files in
drivers/bluetooth and subsys/bluetooth, the configuration option itself
now lives in the top-level Kconfig file for consistency.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to auto-update Bluetooth PHY to 2Mbps
if the local Controller supports it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added support for Bluetooth v5.0 PHY Update Procedure in the
Controller.
Asymmetric PHY connections do not work for now due to the
Radio mode not being setup in time in the ISR during tIFS
period and the Radio already ramping up in the cached
previous Radio mode to meet tIFS deadline.
Subsequent commits will add this feature, by either double
buffering the mode in software or using fast radio ramp up
which gives enough time in the ISR to change the mode.
Jira: ZEP-2086
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Scale the ctrl pkt enqueue implementation to allow multiple
ctrl packets to be enqueued. This will aid in the graceful
implementation of parallel control procedure collisions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added HCI macros to check LE Features. Also, added test
macros for 2M and Coded PHY support in HCI Controller.
Earlier a common test macro was used between BR/EDR and LE,
but since LE features do not use pages for feature, an
explicit macro for testing LE feature is added now.
Also, features field in LE device structure is now a single
dimension array of 8 octets.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The APIs for allocating RX buffers were modified recently and hci_raw
had not reflected those changes properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When we send TCP data segment, we need to set the length
of the application data by calling net_pkt_set_appdatalen().
This is done so that sequence number can be properly
advanced when we receive ACK to that pending packet.
Signed-off-by: xiaorui hu <xiaorui.hu@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The event mask population used to let the Controller know which events
are relevant to the Host needs to take into account the features
supported by the Controller itself, in order to only enable those that
are indeed valid.
Jira: ZEP-2050
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the framework for LE Scan Request Received Event.
The feature is available under the Controller's advanced
features and will be selected implcitly when Bluetooth v5.0
LE Advertising Extensions feature is implemented.
Jira: ZEP-2073
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove unreferenced function hci_evt_is_discardable after
introduction of hci_get_class function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation for refactoring the Controller implementation
into seperate state and role based source files, add Kconfig
options for states and roles in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To guarantee code that is endianness-independent, the sys_le* macros
must be used everywhere when accessing multi-byte values from the
command parameters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In HCI, the response buffer to a command is the same as the one for the
command itself, requiring command parameters to be processed before the
response is formed on the same memory area.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since Controller to Host flow control is a feature that affects both
sides equally, move it to the top-level Kconfig file and consolidate its
use in both Controller and Host.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This feature was removed some time ago, but turns out it's important
to have it available for split host-controller setups.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable the bits corresponding to the new 3 commands supported when
enabling Controller to Host Flow Control, in order for the Host to be
able to enable the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to achieve proper sharing of configuration options, everything
that is common to both the Host and the Controller should now be placed
in the top-level Kconfig file, and Controller-only options are in the
controller/ Kconfig one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Introduce alternative TRX switching using dedicated timers
and peripheral interconnect. This will enable the
possibility to independently configure the Tx and Rx
settings between the tIFS.
Note, this will also provide the opportunity to design a
soft realtime Radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The Bluetooth Specification allows for optional Controller to Host flow
control based on the same credit-based mechanism as the Host to
Controller one. This is particularly useful in 2-chip solutions where
the Host and the Controller are connected via a physical link (UART, SPI
or similar) where the Host is sometimes required to ask the Controller
to throttle its data traffic while still making sure that relevant
events get through the line.
This implementation is based on a simple queue of pending events and
data that is populated whenever the Controller detects that the Host is
out of buffers and then emptied whenever the Host notifies the
Controller that is ready to receive data again. Events relevant to the
connections are also queued to preserve the order of arrival.
At this point the Controller ignores the connection handle sent by the
Host and treats all connections equally, and it also queues events even
for connections that have no data pending in the queue. Both this items
can be improved if necessity arises.
Note that Number of Completed Packets will still flow freely from the
Controller to the Host regardless of the pending ACL data packets, which
might lead to inconsistencies in the sequential order of certain
operations that include bi-directional data transfer.
Jira: ZEP-1735
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When adding link-local address to the cache the type needs to be
properly set as net_ipv6_addr_create_iid will attempt to use it
when generating the IPv6 address.
Jira: ZEP-2077
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is related to commit "net: tcp: Make sure ACK timer is not
run if cancelled" which did not set the cancel flag when the timer
was cancelled from tcp.c.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
And print a warning if that happens.
This will also avoid to raise an ASSERT on net_if_tx_thread()'s k_poll
as this one will be called with no events to work with.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This ensures that an unknown request won't cause ATT to timeout since
no response is currently generated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Rename ll_address_* to ll_addr_*. Also, update ll_addr_get
to return reference to stored public or random address.
Change-id: I22cb0135d2223f679c4d9321f4724f8b7de0aede
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Fix the attr->handler reference to attr->handle.
Change-Id: I4a6ccee7860abf800f51df404979eac18eb26e8e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Rename occurences of bt_hci_ev_* to more widely used
bt_hci_evt_* namespace.
Change-id: I742fb86f8f835a0f6072638e1e997ad08891d43d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
In the Controller's radio hal, explicitly differentiate
between Advertisement and Data channel packet
configuration.
Also, remove nRF5x specific extra overhead in Advertisement
PDU structure.
Change-id: I942b88a160af78f8900d7e49fb5f36c8aa493b97
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
L2CAP Dynamic Channel feature uses the global connection Tx
pool for segmentation either when there is no free buffers
in the original application pool or when the original data
buffer has no headroom to add L2CAP headers.
This eliminates the need for a dedicated fallback pool for
Dynamic Channel segmentation.
Change-id: Ia5452c814169d17ef261ecef425a8fcf2e7e1e84
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This function already has an 'i' variable on the top-level, so no need
to declare a second one that'd just shadow the original.
Change-Id: I5dfa4df2c4793be220a40ac642b19bf440e80220
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The segment allocation function can't fail (it eventually waits with
K_FOREVER for a buffer to become available), so there's no point in
checking its return value for NULL. Also, the connection state check
is because of this particular waiting and not the semaphore waiting
(which is done with K_NO_WAIT).
Change-Id: I9698760541de810869cffc1c60cf97c5f8f7df8d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
L2CAP Tx segmentation used BT_L2CAP_RX_MTU value which is
the value used by fixed channel protocols. Decoupling the
buffer size provides the opportunity to reduce RAM used per
connection.
Change-id: Id064f9b2e3f02073402815d09c3ea13a35df2a6c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Remove BT_ prefix from BT_L2CAP_MAX_LE_MPS and
BT_L2CAP_MAX_LE_MTU as they are internal to l2cap.c file.
Change-id: I6abec0a1f07b8aef49940ab7abeaacbd19947e0b
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: I1448b159ab1afe50ff88b7a6bd1b254c44858d4c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This information should be part of the main BR/EDR context struct,
rather than there being a separate member in struct bt_dev. If/when
the needed ESCO information grows we can consider having a separate
struct, but even then it should be part of the main BR/EDR struct
instead of sitting directly in bt_dev.
Change-Id: I3edf120606ea6c6974f515bba90de2b25fc6fac6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: Ic0e33dc199f834ad7772417bca4c0b2d2f779d15
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This should fix the grouping for debugging options appearing in the
main "menuconfig" menu.
Change-Id: I7ddf3a6f3d025bf82ba63099b30e47a40d7c3187
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The highest endpoint number supported by the STM32F4xx USB device
controller is 3. Change the cdc_acm driver to use endpoint 2
instead of endpoint 4 so that it will work with this platform.
Change-Id: I4a3cd08f546a7fe01558528de0990156f642d93b
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Instead of returning EIO let's bubble the error from net_context_send
back up to the caller in the following functions:
mqtt_tx_connect()
mqtt_tx_disconnect()
mqtt_tx_pub_msgs()
mqtt_tx_publish()
mqtt_tx_pingreq()
mqtt_tx_subscribe()
mqtt_tx_unsubscribe()
Change-Id: I9bb4396b227b8902ac1195a97bc37eb1959b643e
Signed-off-by: Michael Scott <michael.scott@linaro.org>
With CONFIG_NET_DEBUG_NET_PKT enabled, the log messages are full of
errors regarding NULL parameters passed into net_pkt_unref in almost
every TX function for handling MQTT messages:
mqtt_tx_connect()
mqtt_tx_disconnect()
mqtt_tx_pub_msgs()
mqtt_tx_publish()
mqtt_tx_pingreq()
mqtt_tx_subscribe()
mqtt_tx_unsubscribe()
mqtt_parser()
Let's clean up the unref handling so that our debug log isn't quite
so full of error spam (as opposed to the normal amount of spam from
the net buf log).
Change-Id: Ib49d1192f51abe4329e6dc9da3c51a4a36290082
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The data->len of an inbound netbuf can be larger than a single
MQTT packet. For instance when a PINGRESP is also included
in the same netbuf. For this reason we should not be using
the data->len to determine how large the rest of the MQTT data is.
Specific Example: we've seen in testing that PINGRESP packets
can be included with a SUBACK packet in the same netbuf. Under
this case the current code uses the data->len incorrectly and
tries to find 3 QoS elements for the SUBACK packet when there
is only 1 (the rest of the data is for PINGRESP).
NOTE: A larger patch to iterate through the netbuf data parsing
individual MQTT packets will be needed to fix the MQTT subsys.
This patch only corrects the SUBACK parsing.
Change-Id: I7f6cebaaed9570b778d466de84331cf8c5060755
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Currently, app type MQTT_APP_PUBLISHER_SUBSCRIBER is not supported.
mqtt_init() will return EINVAL because the context rcv function is
either mqtt_publisher_parser or mqtt_subscriber_parser (not both).
Let's combine these functions into mqtt_parser and remove the app
type check from mqtt_init().
Change-Id: I60460e011395864706e293c997e9f8a65681b368
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We need to set the mqtt context recv function prior to calling
net_context_recv which installs the mqtt_recv callback.
If not, we risk a race condition where an unprotected reference
to mqtt->rcv(mqtt, buf) is made in mqtt_recv().
Change-Id: If90ee58f4ea6f7879ef7c12b969ba27647426acc
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Some applications may want to reuse implementations of these
commands for debugging/diagnostics purpose even if they don't
use net shell per se, or implement an alternative shell.
Jira: ZEP-2064
Change-Id: I48cb66ccc41bd41a75a4eb8eb3c366316ec5a096
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_if_ipv6_router_add() will return router pointer on success.
This information must be cached in RPL instance, otherwise RPL
instance doesn't know about default route.
Change-Id: Ic6d80ebfa95c9a64df9adf2621ae2631d9bdb990
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When router or default router timer expired, interface will remove
router from the list. In this case RPL does not know about this.
When RPL node receives DIO messages it only verifies whether parent
exists or not. This extra checks will verify whether router really
in "used" state or not.
Jira: ZEP-2080
Change-Id: I4b36b3a2d495e76a38caddd058451daff08fab0c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_if_ipv6_router_rm() is the correct API to remove IPv6 router
from the interface as it also cancels the timer and raises a mgmt
event. The net_if_router_rm() only sets router as unused and
nothing else.
Change-Id: I55114288c9ae748520b67b206edcd4f5e420b1af
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If the ./well-known/core response is bigger than L2 MTU then
response will be sent in multiple fragments. In mesh kind of networks
getting response from farthest node might loose packets. So better to
send response in a block wise fashion. Block size is configurable.
Change-Id: Id421c66597fe448c12a7215f04f63f4a284c14ab
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Value 0xFF represents End Of Options marker in CoAP message.
Use #define than magic numbers in code.
Change-Id: I3bef21ea827987f7c2e670447ee20574cb6288ae
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add timeout for packet and buffer requests. If there are no
buffers available gracefully drop the request.
Change-Id: I56fe2b606556149c83751aadc1c5eee7828a84a8
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Bluetooth only cares about the actual payload so net_pkt can be unref
as soon as the data fragments are detached.
Jira: ZEP-2070
Change-Id: Id528d5440f42903378883f5e696b3f663bbfa313
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Instead of just plain assert, check that the packet we receive
is ok before passing it to processing function.
Jira: ZEP-2057
Change-Id: I5754c82d16e1522d8fcee561eea280eadeec31ee
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The TCP trace values were not printed because of incorrect
config option used. Print also seq and ack values in decimal
in order to make it easier to correlate the values in other
prints in tcp.c.
Change-Id: I44d1535a84dcba8c6c937d348516ba801193ca23
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use ready-made utility function which can take care of endianness
Change-Id: I1edd0b2ce1a086dd637e97308145f9b434e48a1f
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When connect to diffrent router with the same gateway ip address,
need to clear arp cache when disable interface,
or it will use the wrong gateway mac address.
Call net_arp_clear_cache function replace to set arp_table 0.
Change-Id: Ib403a0c0030832ba48824db4d2d3fcb8add63d16
Signed-off-by: june li <junelizh@foxmail.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Change-Id: I9ccb7c01a7d8c4ad8b1e55a1b45622aad2a57e57
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a new event type to the kernel event logger that tracks
thread-related events: being added to the ready queue, pending a
thread, and exiting a thread.
It's the only event type that contains "subevents" and thus has a
non-void parameter in their respective _sys_k_event_logger_*()
function. Luckily, as isn't the case with other events (such as IRQs
and thread switching), these functions are called from
platform-agnostic places, so there's no need to worry about changing
the assembly guts.
This is the first patch in a series adding support for better real-time
profiling of Zephyr applications.
Jira: ZEP-1463
Change-Id: I6d63607ba347f7a9cac3d016fef8f5a0a830e267
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: Icbf9e542b23208890a3a32358447d44cdc274ef1
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was compiler error if CONFIG_NET_DEBUG_CONN was set.
Change-Id: Ibb6721c55dd2c56cd0097359a53563c6221859ea
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to set the connect_cb for the context before sending SYN packet.
This is required if we have a loopback connection in which case everything
is happening more or less synchronously and the connect_cb would not be
called in this case because its value would still be null.
For remote network connections this patch makes no difference.
Change-Id: Id7f837cd9e81cd79c4666c98cae84f6cb1a77af0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We must not let ACK timer to run if we have already cancelled it.
So keep track that the timer is cancelled and refuse to run it
if it was indeed cancelled. The reason why the timer might be run
in this case is because the timer might be scheduled to be triggered
after which one cannot cancel it.
Change-Id: I1c8b8cee72bc7a644e02db154d9d009b8d98ade2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The local port was set to 0 for IPv6 when registering
the connection handler. For IPv4, the code was not setting
the port in local_addr struct.
Change-Id: I82f0c08641a94d75d255ac306eca7bec6c332fba
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Without this info it is a bit difficult to notice what is going
on in loopback case.
Change-Id: I8f61330c01d025e41f00d663bd26947b8cafb5c0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support to print connection handler information in net-shell.
There exists one connection handler for each UDP/TCP port that we
are listening. These prints are only available if CONFIG_NET_DEBUG_CONN
is enabled because the net_context has the same information. Thus the
connection handler info is only printed if debugging is active in order
to verify that handler information is proper.
Change-Id: I0be39a5adb89b2cdbd85524c5d943e4a562b0fde
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If TCP debugging is enabled but if the loglevel is set to lower
than 4, then compiler prints warning about unused flags variable
in net_tcp_trace().
Change-Id: I2e663644b50fe97b75088202e21b286aa010953e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Only 2 attributes lacked this prefix, which makes sense to have, so
applying it accordingly and changing the helpers as well.
Change-Id: I095b2729f977f8fb1624eff8801a4a4e21416693
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
IPv6 next headers are processed in a way so it is not required to store
which header has been already seen in the net_pkt, as the processing loop
can store internally which one it has seen already.
Change-Id: I266ba8a3a0081a162318cdafb474a0fc44a3185e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is actually useless as there is only 1 RX memory slab, and thus can
be removed to reduce net_pkt structure size.
Change-Id: I62d716515120e7356ee1e2d75bbe1ec32e22c35d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix warning using incorrect format specifier
Change-Id: Ib6800c40b2cd769612ae6f107e41a941926d8e66
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
We need to check whether buf_sent was true when resending the TCP
segment, and do a buf ref if needed. If this is not done, the buf
will be unref after send, which will cause unpredictable results.
Change-Id: Ibd4490305de88ac6ffd04ec42bba196e57da5c10
Signed-off-by: june li <junelizh@foxmail.com>
While very unlikely it might happen that fragment pointer is NULL
when going through fragment list.
Coverity-CID: 167148
Change-Id: Ic3dbed7ee29c7b864d4830d726f65d7f62dcea84
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If error occurs while preparing response to .well-known/core request,
do not send partly filled payload by simply changing code part only.
It's better to unref the partly filled reponse and prepare a new error
response and send.
Change-Id: I28013a4e331cfc6f01de873e80af48f765e49494
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Commit "net: zoap: Fix memory overflow issue" fixed and implemented
./well-known/core response in a different way, so this api is not needed
anymore.
Change-Id: I8f945fb5842028be50ecfdef95cbe5da3189a538
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If CoAP .well-known/core services list is bigger than single fragment
then current helper functions overwrites beyond fragment space. Which
corrupted whole stack. Right now sending response in multiple fragments
but preferred way is send response in block by block. This should
overcome packet loss across mesh scenarios. Recommended feature will
be supported with later patches.
Change-Id: I30ca55bde2516d80b3583731241ad295799c6614
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Most of the zoap utilities deal with first fragment of buffer chain.
So accessing of buf->frags directly make less usage of stack than
delcaring another variable for frag and its data. Due to code
refactoring couple of lines removed and in between those lines
coverity complained two issues, which is not valid now.
Coverity-CID: 157597
Coverity-CID: 157598
Change-Id: I3035c0625a131d49a4f0250ff0052875d3382544
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When net_ipv6_finalize_raw() inserts RPL(HBH) header after IPv6 header,
it updates IPv6 next header as HBH and HBH next header as original IPv6
next header.
Then net_ipv6_prepare_for_send() will update RPL HBH header if it exists.
But net_rpl_update_header() is comparing HBH option and IPv6 next header,
which is wrong. Wrong comparion does not update RPL instance id and
sender rank. Peer nodes drops all the packets due to invalid instance
ID and sender rank.
Change-Id: I91c1870a09c60f8e1ebc73e434dcc208caf6299a
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Following flow does not work:
net_context_get
net_context_bind
..
..
net_context_put
net_context_get
net_context_bind
At instance of call to net_context_bind, conn_handler
is not NULL and returns with EISCONN.
This patch sets conn_handler to NULL in net_context_unref
Change-Id: I56a50839101b22161644b3cd7c5f510fa1abae3e
Signed-off-by: Mitul Shah <mitul.a.shah@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I8f57a17f78e674aca5400f005db8975c9f9e150e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If there are many connections there may be some delay before an ATT
PDU really gets transmitted over the air. Use the TX callback to
start the response timer so that it doesn't expire too soon.
Change-Id: Ibdd5bc1029ae4034caf329bf03892ac2093a0c67
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to not overload the TX buffer pool and potentially run out of
them, enforce flow control for outgoing ATT packets so that the send
functions block until the PDU has actually been transmitted over the
air.
Change-Id: Ic065bb88aec8c2d0ac2def8ef62131a427f7051f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This CONTAINER_OF() worked by chance, but was actually wrong, since it
makes it look like bt_l2cap_le_chan is the parent container of bt_att.
Instead bt_l2cap_le_chan is simply a member of bt_att, i.e. we can
dereference it directly.
Change-Id: I7307517bae823e54b45db31f75462655ce6eb50d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no command that should take more than a couple of seconds. If
it does there's something severely wrong with the system. Catch such
situations with a clear assert rather than silently blocking the
sending thread.
Change-Id: Ie981fddcc27059df3e4df586e86ceac2e348f509
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
According to the SMP specification the pairing is only to be
considered complete once the last SMP PDU has been transmitted over
the air. Take advantage of the new TX callback to notify completion
only once the packet has really been transmitted.
Change-Id: Ic87e598cd0e040d99f38344b98e476f67e4d9762
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's not valid for a peer to send another request before getting the
response to a previous one, or to send another indication without
getting the confirmation to a previous one. Take advantage of the
recently introduced TX callback to track when it's ok to accept these
ATT PDUs again.
The HCI USB transport has a potential issue here since a race
condition can occur between the ACL data and HCI event endpoints,
leading to dropping data when in fact both peers were behaving
correctly. To avoid hitting this issue, disable the flow enforcement
by default on the qemu targets that commonly use a USB-based
controller on the host OS.
Change-Id: I2791aaec6f6c0f8fd78a9a809a25e3ce129106c7
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Protocols/profiles may want to know when exactly their PDU has been
transmitted over the air. To make this possible, introduce support for
a callback that will get called when the controller reports that a
packet has been transmitted (through the Number of Completed Packets
HCI event).
Change-Id: Ia3a19b93c5b2111f144bfabe5861187c41525f30
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the ECC code was last time refactored hci_raw.c was forgotten
about. This fixes the issue so that ECC works again with hci_raw.
Change-Id: I1b1df66f1b2a311db611b9936ec074c88caf4143
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This reduces the pressure on TX pool which may constantly block in case
of heavy traffic causing the RX thread to block as well.
Change-Id: Icfdde32031715e882085b7fa371191f157954156
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds net_buf_reset which can be used to reset the state of a buffer.
Change-Id: I4b7c89dfd1a23a2ec8dfa3c99d5b02b9bcbceef3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes the code attempt to allocate from the original buffer pool
before relying on le_data_pool which shall only be used as last resort
as it is configure with minimal possible buffers (1 per connection).
Change-Id: I85b581627f5c3b1bf1ee7c5fa69099c5aca13d4a
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Added support in the Controller for increased feature set
bit fields in Bluetooth 5.0. Cached feature set in the
connection context is increased to a uint32_t value to
accommodate 17 feature bits.
Change-id: I9ae15d6d90fa7a3de186905d3c68088ee22d2911
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
With the introduction of event mask implementation in the
Controller, it is discovered that peer centrals
initiating LE connection parameter requests timed out as
the Host did not get/enable the HCI LE connection parameter
request event in the set LE event mask command.
Fix by adding the LE connection parameter request event bit
mask while creating set LE event mask command.
Jira: ZEP-2027
Change-id: Ida7750f375addc8a91036fffc47325518a3d2ec0
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To avoid having to define a BIT64() macro in a public namespace, use
instead masks directly instead of bits, and also refactor the host code
so that it uses those instead of the earlier byte array with hardcoded
indices and masks.
Change-id: Ief03db616a96df65349d24289b62566a268ffdd0
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Rename symbol names with channel/chnl to chan.
Change-id: I196ffea79e7e10b0253363949051fdf82be62cb4
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Since the type of int, uint32_t, etc change with newlib we get the
following error:
subsys/bluetooth/host/at.c: In function ‘cme_handle’:
subsys/bluetooth/host/at.c:272:25: error: passing argument 2 of ‘at_get_number’ from incompatible pointer type [-Werror=incompatible-pointer-types]
if (!at_get_number(at, &val) && val <= CME_ERROR_NETWORK_NOT_ALLOWED) {
^
subsys/bluetooth/host/at.c:46:5: note: expected ‘uint32_t * {aka long unsigned int *}’ but argument is of type ‘int *’
int at_get_number(struct at_client *at, uint32_t *val)
^~~~~~~~~~~~~
We we can easily address by making val a uint32_t.
Change-Id: Ie6988368bd862afd4075baede7cb0a66c1628c18
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we use newlib the isdigit (and other similar functions) return an
error as char can possibly be viewed as signed:
usr/include/ctype.h:57:54: error: array subscript has type ‘char’ [-Werror=char-subscripts]
#define __ctype_lookup(__c) ((__ctype_ptr__+sizeof(""[__c]))[(int)(__c)])
Being explicit about the char being unsigned char deals with this.
Change-Id: I348189e1df11a1fcc58e5810b010b602fd2df33e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For consistency, "chan" and "param" are used wherever "channel" and
"parameters" are the words in the specification.
Change-Id: I778a8501ae6af991618c14cc6e395d765a9ae102
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix doxygen comment typos used to generate API docs
Change-Id: I3efff6f5fa26f87d1e658d6336fef01ce45f5bb0
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Use UNALIGNED_GET and UNALIGNED_PUT throughout the networking stack to
access fields from the IP address structure. These structures can be
mapped directly to buffers and the macros are required for correct
unaligned memory access.
Jira: ZEP-2012
Change-Id: I55f9da7b143a22fa869d5d215c661de988cd9b91
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This can be useful to override the default value, for testing.
Change-Id: I23b559152c71955ff5aa6fd3643f1f40f5594194
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This permits to tweak the TX power in dbm.
Change-Id: Idadff397941a39010ce3c374d9ca74b777934626
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This does not save any space but sets the fields in the
structs in more natural order. Move IPv6 related
fields in net_if into internal ipv6 struct so that all
IPv6 fields are located inside one struct. Same thing
is done for IPv4 fields which are now located inside
IPv4 internal struct in net_if.
There is no functionality changes by this commit.
Change-Id: I7d72ec0a28e2b88c79a4c294655d5ef6da6ccb25
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
So manipulating it requires to be ready to swap it if the CPU is BE.
Change-Id: I8d657c31cecfc9f3fcd010efbb6d090bf021f5f5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DNS resolving is better done with DNS resolve API so remove
the DNS client API which is quite hard to use.
Change-Id: Ide4973a5be674414ea6e04a35c938195cce40b6a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need a way to know when IPv6 address is successfully set
into network interface.
If IPv6 DAD (Duplicate Address Detection) succeeds or fails,
we send a management event for that. This can be used by
other components to detect when the network interface is in
usable state.
Change-Id: Ifb22415fe21f31f5dba4f55455d6e0f89b414d32
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the IPv6 utility functions were missing const in
one of the parameters that are not modified by the corresponding
function.
Change-Id: Ic9fe53daac288570c14423fd9410dcf15d1c5cfa
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This makes net_ipv6_nbr_add able to update entries so it can be reused
when receiving RA or NS requests, so it now performs a lookup before
creating a new entry (using nbr_new to reuse more code) and in case it
finds a match attempts to update the lladdr.
Change-Id: I305a67a955e037cbbb862fef947a5fcfe131507c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
net_ipv6_nbr_add shall init the delayed work as nbr_new does, so this
unifies both codes into nbr_init which does take care of initializing
the fields properly.
Change-Id: I91746276d346a3dc3c36be20d49bcf1968245fc5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Route lifetime was printed using wrong modifier.
Change-Id: Ib503d50b5817491984d51bbdaadf7457fdde178b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure the RPL is compiled ok if CONFIG_NET_RPL_MRHOF is
enabled in the configuration.
Change-Id: I51fc0e20f854164c7e0374fa6a1ebf1d4e4dbc5b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If multicast routing is set meaning that MOP3 (Mode of Operation)
is enabled, then the code was not compiling properly.
Change-Id: Ice8a9f7b705c781536d3c2c5ca6cc2bb77a7acc1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print information about configured DNS servers when starting
in order to ease the debugging.
Change-Id: I3ba71e514e463db790b82913e4c66a67160366dc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to set the resolved IP address family and length
before calling the user callback so that callback does not
need to figure out these values itself.
Change-Id: I724909fc1707608ab8728231a0311795b6a313f3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default hop limit is defined in struct net_if. It is possible
that user might want to tweak it for each network packet. For this
purpose, a net_nbuf_set_ipv6_hop_limit(buf) function is created.
Change-Id: I7568330358f80f0f5007d6d3c411c120b043c04f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The Kconfig.rpl file was missing option to actually collect
RPL statistics. Unified the config option name to be
CONFIG_NET_STATISTICS_RPL as there was two conflicting settings
in the code and both of them were missing from Kconfig file.
Change-Id: I4ce4fcbaa317b36cac315ea3b3f710fa7a344b25
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The probing_timer is only available if CONFIG_NET_RPL_PROBING
is defined.
Change-Id: I2835d17e6c3d616f815f8beefd87d2571a5ad94c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
After failing to send the buf we need to release it.
This is not done for Bluetooth or IEEE 802.15.4 links which
create a copy of the sent buf and the failure case is already
checked by net_tcp_send_buf().
Change-Id: Ia556376b58ad74f68accb64eb2221a78d59dc2ec
Signed-off-by: june li <junelizh@foxmail.com>
In case CONFIG_NET_BUF_POOL_USAGE is defined use print pool->name
instead of the pointer.
Change-Id: I0be5fd8283a887145e61bdad02f721265453ce20
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use UNALIGNED_GET in net_addr_ntop as the uint16_t pointer used in this
function can point to an unalined address.
Jira: ZEP-2012
Change-Id: Idfbfa8da4c8d4e10299c4ae4d6431b10466cc988
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
If the IPv6 fragmentation support is enabled, then print current
status of the IPv6 packet reassembly in "net conn" command.
Change-Id: I384e35928b67dd39ac720c77683b1767e2a1ce88
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Figure out what is the last extension header in IPv6 packet
and return offset to it. This is needed by IPv6 fragmentation
when fragmentation header is added to the packet.
Change-Id: I925ab806a5de076a425ff354711730d4f4b3c52f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds support for IPv6 packet fragmentation when
receiving (IPv6 reassembly) and when sending larger than 1280 bytes
long IPv6 packet. See RFC 2460 chapter 4.5 for more details.
Jira: ZEP-1718
Change-Id: Ia31c147cce4d456ee48f39276cca99aa09ce81d6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add net_nbuf_split() function that can be used to split
an existing net_buf fragment into two arbitrary length pieces,
and return the two new fragments to the caller. The data from
the original fragment is copied into these two new fragments.
Existing fragment is not modified.
Change-Id: I463e675232c6e19c2a42929f480893a6d1265873
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not try to cancel query if the DNS query index is < 0.
Coverity-CID: 166770
Change-Id: I03c1f274453640d0ff80694628b8e8f18e8de900
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use UNALIGNED_PUT() to store the MSS value into network packet
because the memory location cannot be guaranteed to be properly
aligned.
Change-Id: I77fd7a70ef45eedb657cac29457b0239b0a1d4c2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_* usually come from Kconfig, rename variables that are locally
defined to avoid confusion about where they are set.
Change-Id: I402713e6f852907e75be4bc2b916a7d15dd5649c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This fixes regression introduced by
87f2f7afec.
Change-Id: I4a1177ad42c7bb20fe66f8927cd00a30236152af
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the connection process fails the user may still need to do
bt_conn_get_info() in its connected callback, so this needs to give a
meaningful value for the remote address. Start off with the one that
was given to bt_conn_create_le().
Jira: ZEP-2005
Change-Id: I4e9a033dec7c55fa549f5b6746c3bd81c0ccade5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This replaces custom made list manipulation with sys_slist_t which makes
the code more readable.
Change-Id: I9ee024ad83da3e28f2ecab74b001bf0e795fe489
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use #if defined(...) constructs while using conditional
compilations of advanced event preparation and advanced
scheduling implementations.
Change-id: I728c76d0e7dbbfa378e8978b726ec404d9e55a72
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the scan duplicate filter length option and group it along
with rx/tx buffer size Kconfig options.
Change-id: I3df07e667029c7d2571270db442ecb7241a417c2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The bt_conn_set_state() function will not notify the connected
callback of the connection error if conn->err isn't properly set.
Jira: ZEP-2005
Change-Id: Idc30e736f4d8ba00156bf5c0e37dcccdb151742f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CONFIG_DEBUG_INFO was disabled for IAMCU targets. As per Jira update forked
arch/code is gone. So it should not block enabling DEBUG_INFO for IAMCU.
Currently CONFIG_DEBUG_INFO depends on (x86 = y && !X86_IAMCU)
CONFIG_DEBUG_INFO can not be set for IAMCU. this patch removes dependency.
Jira: ZEP-601
Change-Id: Ib5635096f83f7b931c277b667a55c6d54f8e946a
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Conditionally declare the iterator variable to avoid a warning when
compiling the controller without any duplicate filter entries.
Change-Id: I69e23d4c594db18172dc57d45e7925243fe2da69
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The main issue is that after the latest update to TinyCrypt the
ecc_make_key() API expects a twice as big random number. Fix this, but
also move the variables to the static context since we're limiting one
HCI command at a time. Also place the variables in a union based on
their temporal dependencies. Thanks to this, we can now further reduce
the ECC stack size by 40 bytes (on ARM this then reports 12 bytes of
unused stack after key-pair generation and DHKey calculation).
Change-Id: I1036e0ca15f7c08063cba9e568d7df99e65c9156
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
HCI event masking allows the host to choose which events are reported to
it to avoid interruption and excessive traffic. This patch implements
masking to drop any non-enabled events as specified by the host.
Jira: ZEP-1769
Change-Id: If09d4aa22b0da8f743fc42a3b0db3f369daaff96
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the controller's ability to drop duplicate advertising reports
when instructed by the Host.
Jira: ZEP-1246
Change-Id: I2d1b7abf1ed950dde705e5df30a858c595f3834c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add Controller advanced Kconfig options to select IRQ
priorities of the Radio, Ticker's Worker and JOB IRQs.
This will provide an opportunity to have peripheral IRQ's
of higher level than Bluetooth Controller.
Change-id: Iaa128c1cd64a309a77d42d485fdefe68f31e4895
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the nRF5 specific GPIO debug pin macro definitions to
hal/nrf5/debug.h.
The Controller's hal folder contains prototypes and
hal/<soc> shall contain SoC specific implementation to
realize a software-based Link Layer.
Change-id: Ic7bf283f926bbc3069e7d15c047fe93a6daa894f
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Cleanup redundant ticker busy loop that could hang if the
worker and job IRQ priority levels are misconfigured, and
job gets disabled before all users/mayfly functions using
job complete.
Change-id: I053ad75a4328c51cfe651b820a2fa961e42ae48f
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
In a host plus controller combined build, if no connection
is required, deselect CONFIG_BLUETOOTH_MAX_CONN. This will
reduce RAM and ROM usage in the controller.
Also, make BLUETOOTH_PERIPHERAL, BLUETOOTH_CENTRAL and
BLUETOOTH_CONN switches accessible by the controller kconfig
to select the right roles to enable.
Change-id: I164cf696ab2a6f4859086d2cb18f6d3f2b1399d3
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
BR/EDR sources that was compiled under BLUETOOTH_CONN
if-clause is moved out as independent conditional
compilation based on selected BR/EDR feature support.
Change-id: Iedfafc6056132654a9150ed235b245f8be62b4b1
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
If during hfp_hf_send response callback is not filled with NULL
and you receive unsolicited callback. which will not be taken care.
This patch fixes this issue.
Change-Id: I04007059d62273b9cdddf29e2d4a9086b07a01e5
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
A initiation to send AT commands is given in the application
with prefered AT command as the argument.
This patch supports to send the command within the profile stack.
Change-Id: Id5caa3ce64070fc17e60f4ea61a8c83a961099ba
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This cause packets that are up to 2 bytes off segment maximum length
to be considered transmitted when in fact that could be some bytes left
to be transmitted which cause any subsequent packet to trigger invalid
SDU on the remote end:
[ 3612.376068] l2cap_le_data_rcv:6757: SDU fragment. chan->sdu->len 66 skb->len 68 chan->sdu_len 67
[ 3612.376073] Bluetooth: Too much LE L2CAP data received
Change-Id: Id2f3469ce1c0b27bb87c4d5bc18e6ede9d93dbde
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move the Kconfig option BLUETOOTH_MAX_SCO_CONN to BR/EDR if
clause.
Change-id: Iead2bc5a70a9499125f9edf22e85ade4dda8f5ac
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the BLUETOOTH_UART_TO_HOST_DEV_NAME options to after
BLUETOOTH_HCI_RAW option to group it together in the
Kconfig while using menuconfig.
Change-id: I21da080a5ffa30a08b1a1aa148ce8116e63a3c18
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Group the stack size related options together to represent a
better order when using menuconfig.
Change-id: Id2968607e5054e30029c42987b3e70cb8cbfc74d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the Kconfig BLUETOOTH_CONTROLLER switch from top-level
Bluetooth Kconfig to Bluetooth Controller Kconfig.
Change-id: Iead760c22a0fbbda11e4558c4943b3366ecc8769
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This makes the code consistent with respect of errors, so instead of
checking directly on bt_gatt_write_without_response let this up to
bt_smp_sign.
Change-Id: Iea8d0bd2020df427b7542e2878ce8d9fd8b94170
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When there's no support for connections there's also no need to track
the controller side buffers.
Change-Id: I7eac3af486f139f1ab32efda8ccfa188ed8359eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Checking both if signing has been requested _and_ conn->encrypt can
bypass signing leading to the caller to assume that a proper signature
was send in when fact it was not.
To fix now the code explicitly checks if SMP is enabled and in case it
is and signing was requested fails.
Change-Id: Ie17df4a4c2191f2da0172c687db7999395839a97
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case the controller is receiving PDUs very rapidly, prevent it from
spamming the logs by limiting its stack analysis to at most once every
5 seconds.
Change-Id: I31c70d28e8af62b27172a4a77bf6e614ea3e20eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move company id and subversion number Kconfig to the
Controller configuration section from the features section.
Change-id: Ic4deb8b24d84d9b1817ba542705eebd612f0e020
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added a explicit Kconfig option to show the Controller's
advanced feature configurations. These feature
configurations need specific in-depth Controller
implementation knowledge and should not overwhelm normal
users of the Controller.
Change-id: Iae764f2b266b199cf180936c51c7a4ea089ee510
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig option to enable advanced scheduling in the
controller.
Enable non-overlapping placement of observer, initiator and
master roles in timespace. Uses window offset in connection
updates and uses connection parameter request in slave role
to negotiate non-overlapping placement with active master
roles to avoid slave roles drifting into active master
roles in the local controller.
This feature maximizes the average data transmission amongst
active concurrent master and slave connections while other
observer, initiator, master or slave roles are active in the
local controller.
Disabling this feature will lead to overlapping role in
timespace leading to skipped events amongst active roles.
Change-id: I16e4e6c3ca99f93987ab86924af0cb9d76bdbc7e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
HCI drivers are obliged to send HCI Command Status/Complete events
from a separate context than all other data, however the ECC wrapper
was violating this rule (sending everything from the same ECC thread).
This could lead to a deadlock if e.g. the ECC API user decides to
generate a DHKey from the same callback that it got notified of local
key-pair generation.
The obvious solution is to emit the Command Status directly from the
send function, before passing the command to be processed by the ECC
therad (through a k_fifo). However, this is not quite so simple since
bt_buf_get_cmd_complete() reuses the original command buffer, meaning
we'd loose the original parameters after sending a Command Status.
To work around this limitation with bt_buf_get_cmd_complete() we stop
passing the command buffer to the thread and instead store the
parameters in static variables and do the thread communication using
flags and a semaphore. One side effect is that only one command can be
pending at a time, however that works out fine for all of the users of
ECC.
A nice side effect of moving some things to static variables is that
we end up reducing call stack usage in the ECC thread, allowing it to
be shrunk by 180 bytes (verified to be sufficient for both ARM and
x86 boards).
Change-Id: Ic41f0316d3fe4d14b64fd3d0a549b221d168411a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added Kconfig option to enable advanced event preparation
feature.
Enables advanced event preparation offset ahead of radio
tx/rx, taking into account predictive processing time
requirements in preparation to the event, like control
procedure handling and CPU execution speeds. Crystal
oscillator is retained between closely spaced consecutive
radio events to reduce the overall number of crystal
settling current consumptions.
This feature maximizes radio utilization in an average role
event timeslice when they are closely spaced by using a
reduced offset between preparation and radio event.
By disabling this feature, the controller will use a
constant offset between the preparation and radio event. The
controller will toggle crystal oscillator between two
closely spaced radio events leading to higher average
current due to increased number of crystal settling current
consumptions.
Change-id: I19e640f7395ac7938873ef4bfac38acf8d6f7e0e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The monitor protocol provides support for logging packet drops with
the help of the extended monitor header. Implement support for this.
Change-Id: I7ef7894816cb8d1bd876842d0253ef0980471e69
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The IRQ lock should never be held for long periods of time. Instead of
using the IRQ lock to prevent monitor protocol corruption simply drop
the data. Follow-up patches will add additional drop count tracking so
that these get reported properly over the protocol.
Change-Id: If498125b29f1b58bed676c78ad2062e2aa206318
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using lookup table to search for unsolicted command and its
handler function.
Change-Id: Id677dad3918d7187e0065ada2985ec12a97f8ed9
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This helps debugging as printable string of the ICMPv6 type is
printed when packet is received if debugging is active.
Change-Id: I22b84bb6b28db7fba030699af3e561a0775b53d2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It requires a net_nbuf, so the actual buf, and not a frag here.
Change-Id: I4fd888c9a91f5e3f3dd664ae5e3bf93f90a2f597
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will refactor net_core.c and move IPv4 specific code
into ipv4.c which is a more logical place for it.
Change-Id: Ia60c5bfec488d2d1a664f113dc3df88e7d5badd1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This will refactor net_core.c and move IPv6 specific code
into ipv6.c which is a more logical place for it.
Change-Id: I5bbecbb760111326b9a6bbef5802c53d7f6efda9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
DROP is only on error case, here it should return NET_OK if it was a
proper ARP packet and it got properly handled.
Change-Id: If347e80a76b3a56a9455b70d11b735c1fd910117
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The context buffer pool was introduced to deal with TCP holding buffers
when 6LO may modify them, therefore it makes sense to have it enabled
by default when TCP and 6LO are enabled given that the code can deal
with NULL pool in case the application don't implement one.
Change-Id: I600ca31ab40c96ee27937c2e885e332b0cee4995
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CONFIG_NET_BUF_WARN_ALLOC_INTERVAL can be used to configure the interval
used to print allocation warnings.
Change-Id: I914f2e0d43b3f00c201e49ff42a45fa950b2df94
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shell crashes if you try to retrieve IPv6 nbr reachable time
when CONFIG_NET_IPV6_ND is disabled.
Change-Id: I3c5b3b5614abf80373b892943fa1ab936d235f3c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Return proper verdict on handling of DIS messages. Otherwise debug
prints will be confusing that packet dropped.
Change-Id: Ia4e18d6238868e3aed4b17e2c9ea11aa432869be
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
No functionality changes, just refactored few rpl functions to
to align nicely.
Change-Id: I05c0397de7a8392cc781de2747802b2dd1bb8146
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Don't assume NULL returns are always errors.
Change-Id: I28d7a0fa6c848e338635010b1fdc9fc3e8440b27
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This might indicate buffer leaks or deadlock is happening.
Change-Id: If91a65ccfe1be9497b210de21e80b533b6739367
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Following changes are made:
1. Output using NET_INFO logging level. This function is not part of
automatic logging, and must be called explicitly by a user application.
But if it outputs using NET_DEBUG, then DEBUG level needs to be
enabled, and the output of this function will be drowned in logging
spam. So, let user to enable just INFO level.
2. Show entire structure of the fragment chain, *including* the head
net_buf which holds net_nbuf structure. It is numbered as -1 in the
output to preserve existing order (and not change existing size
calculations).
3. Show owning pool (and its properties, like buffer size/user_data
size) for each buffer.
4. Check for NULL pointer, e.g. for convenience of calling directly
from net_context receive callback (which will be called with NULL
on TCP peer closed connection event).
With these changes, a newcomer from one look at the output of this
function will be able to have a clear basic picture of network
buffer management in Zephyr, and recurring user will be able to
recall any details at once.
Change-Id: I8f9562748329d749f765cc6af7989a448256d7e0
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
No functionality changes, just refactored net_rpl_update_header
function to align nicely.
Change-Id: I5b3e099593bb964245ca06c9fb2ec85859a0640c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Search destination address in IPv6 neighbor table. If it doesn't
exist in IPv6 neighbor table then go for routing. Added sanitycheck
to verify destination ll address is not the source ll address of
original packet (that means we are re-routing back to original sender).
Change-Id: I24adace6a0d17fbd1d2a36a5d75c79320de0a883
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_ipv6_nbr_lookup_by_index() will always find first matching entry
in IPv6 nbr table with lladdr index. But there can be multiple neighbors
linked to same lladdr index. So find route nexthop with ipv6_nbr_data
from nbr(ipv6 nbr) data pointer.
Change-Id: I5081d40330f5bc1ef0d96def03f4add4808b2fe9
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Router lifetime timer initialized in router_init but not submitted.
Change-Id: If5a77f413832db52eff99e7191f82d2a8fc8f081
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Extra data size was not considered in nbr size calculation.
Change-Id: Idc572abf55c8f9fd19940edb719f58e02e7f8ecd
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Route lookup is necessary only if life time is
NET_RPL_ZERO_LIFETIME, otherwise lookup not required.
Change-Id: I25fb85c53e2d43cfdce08411af385f3ae26384cc
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If DAO message is routed through different nodes or sent directly
to a parent and ACK lost somewhere in noicy network. Node can not
join RPL mesh network properly. So try re-sending DAO message for
max number of trials (Kconfigurable).
Change-Id: I7f6a065deacd1e3942c89118ce8da4fbaa34af51
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When sending TCP data, check if the retry timer needs
to be started.
Change-Id: Iea90716e918dec0b22e60bf32467b11c0d1a296f
Signed-off-by: june li <junelizh@foxmail.com>
k_sem_take() is documented as returning negative value for error and
0 for success. The old code didn't work.
Change-Id: I717b35d73fced476b50e3207410858f86c2ef9bc
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This reverts commit 4e2eaec268.
It's invalid to call k_yield from ISR. In fact, it'll trigger an
__ASSERT.
Change-Id: Icc7b81c07c2e7df63fe7d5029fac446ac6fe508b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If this is not done, there is common pattern that on big input block
(e.g. from a clipboard paste), IRQ routine is called in a tight loop,
leading to circular buffer overflow.
Change-Id: I69a7aa78081b8d74652406f3b3a577ddaf4c5f6f
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This change introduces console_getchar() and console_getline() API
calls which can be used to get pending console input (either one
char or whole line), or block waiting for one. In this regard, they
are similar to well-known ANSI C function getchar/gets/fgets, and
are intended to ease porting of existing applications to Zephyr, and
indeed, these functions (shaped as an external module) are already
used by few applications.
The implementation of the functions is structured as a new "console"
subsystem. The intention is that further generic console code may be
pulled there instead of being in drivers/console/. Besides the
functions themselves, initialization code and sample applications
are included.
At this time, there're may limitations of how these functions can
be used. For example, console_getchar() and console_getline() are
mutually exclusive, and both are incompatible with callback
(push-style) console API (and e.g. with console shell subsystem
which uses this API). Again, the intention is to make a first step
towards refactoring console subsystem to allow more flexible
real-world usage, better reusability and composability.
Change-Id: I3f4015bb5b26e0656f82f428b11ba30e980d25a0
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
It needs to check if current event matches:
- cb's layer
- cb's layer code
- cb's command
If none match, it will not raise the event.
Fixing the unit test as layer must be always != 0.
Jira: ZEP-1940
Change-Id: Iadd63e751fa6e534a10e7da9cae0f5bb5a384461
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most (if not all) 802.15.4 devices can handle ACK replies by
themselves.
Change-Id: I0319d59de767b20eb67c1592bacaa4a7b7015cad
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that interface is not directly used in data and mac frame creation,
let's just pass context pointer.
Change-Id: If002e6790d044eeffc57cb5685ac9525fbd6e43c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that RFD is default, the extended address can be changed through net
mgmt API, and thus no longer be the same as device's generated mac address.
Change-Id: I07ee647615c2caa1994712147c6c8a2b4306900d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no need of interface anymore.
After previous changes, it appears that net_if parameter is not used so
we can remove it.
Change-Id: Id3570f50865696818a9be2280172e2e25fc537f7
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
commit id 7a11439020 changed this.
Hopefully that changed did not affect anything.
Reducing minimal frame length and applying the change everywhere where
relevant.
Change-Id: I5ae203751bfcf70cef833620106d2c2d0e33b7a5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
And use them accordingly in the common code part.
Change-Id: Id91b76e5baea607c0d68eebcde6f84e4e35ca44c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ORFD was a hack, from the beginning of the IEEE 802.15.4 Soft MAC stack,
but is now useless and can therefore be removed.
Change-Id: I74d5e1995993f4a0749b6d9d553406d5ae162bda
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In order to simplify when 802.15.4 is selected on these samples, let's
setup the device through a common code.
For this to work, RFD is now the default.
Change-Id: I46590864442f77d83f681cc0e854c94344648856
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's more readable and along with other part of the system.
Change-Id: Ib4be787d74310d838f38b1f1d5624e7357da8969
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These should be used by samples to fix basic 15.4 settings.
Change-Id: I31ad1540008ac760b7aef720e520bf8e72d3a805
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
s/SAMPLES/APP for name shortening. Applying the change where relevant.
Not only IP addresse will be available as samples settings there but
also IEEE 802.15.4 channel, pan_id, and more for instance.
Change-Id: I05dd24989bd0c804d9588092d67044a3e063bc88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will be needed for Thread/MLE.
Change-Id: Ib421da66cfc4da8111ff131f08cac74a11674928
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These requests are used to set/get the key, the mode and the level of
the IEEE 802.15.4 link layer security.
Only implicit key mode is supported for now.
Change-Id: Ifbc9a5d08f9fbf0d51d6c3e4b650cfdce3d263db
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Initialize the ciphers.
Once the header is parsed and validated, we get all the necessary info
to decrypt the frame properly.
Change-Id: I3142fa572c7566b40efe18cf9d4e3f2b4bce0612
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's not only about decrypting and authentifying but also setting the
right frag's length after that.
Change-Id: Ifc766b212b37d4e3593c210f6646ee85dff2ab6d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Take into account the current security context to compute the header
size.
Provide the function to fill-in the aux security header in a frame.
Finally, call the generic encryption function which will process the
frame relevantly according to the given security context.
For now, only implicit key mode is supported.
Change-Id: I5412c32179e70217c0946b1b54d9a752375d522f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This provides the means to authentify with/without encryption or
decryption of a frame following a generic 15.4 security context.
Change-Id: Ia5dbb7f43936a8131112fe4b16c9780e30f904c1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some call use a boolean for it, and since it's supposed to be 1 or 0
let's ask for a boolean always.
Change-Id: If4fbe5d58d5c25fb2a86719435c59af53ea02445
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When applying security, there will be needs for accessing payload as
well, thus providing the whole frag directly instead of a data pointer
on the ll part.
Change-Id: Ia97a1f07f2a12fc5cdf085c3cc6350d50b419cae
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will ensure basic auxiliary security header fields are relevantly
filled-in as well as moving the parsing buffer pointer to the right
position for further parsing.
Change-Id: Ib09e312add783b13bf8b59a81a2ffe64eb6f8dc2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These will be used to parse and create 802.15.4 frames with security
enabled.
Change-Id: Icad214c8d7aa658b8483bf601b091b266e1b8d77
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the destination IP address is one of our own address,
then reroute it back to us.
Jira: ZEP-1966
Change-Id: I8b93fc5425f3f18b0b9e85ca9a57cb122129c47f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The fields in "net conn" output were unaligned and looked
generally very ugly.
Change-Id: I56b29982d4f6b984405944d155bbb6c682383318
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is possible that CONFIG_NET_CONTEXT_NBUF_POOL is set but
application has not defined any pools. In this case the tx and
data pool pointers will be NULL in net_context struct and we
must use the default pools instead.
Change-Id: I286f34c87d9182aace71e0a61f038945810e4916
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default timeout (4 min) is very long. Allow tweaking the
value via Kconfig option.
Change-Id: Iddfd48b96f3612b9bba7caa4d64357505df9644d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Match neighbour with link layer address. And get RPL parent with
matching ll address. DAG id different which is prefix based address
from the parent.
Change-Id: I75ecdfa7aa63da210676a3f44b8510d24c38d1d5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Let intermediate node reply DAO ACK only if it can not forward original
DAO messages to it's parent. If DAO forwarding is success let the final
parent sends DAO ACK.
Change-Id: I14ff9b5b110a639cad6415741dde71c2cdd222ef
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
DIO message suboptions can contain PAD1, PADN, Metric container,
Routing information, DODAG configuration and Prefix information.
Right now we are not skipping PADN and unknown options payload.
Change-Id: I43557962784f68a223ea209eae5ca0367a3d5410
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
DAO message suboptions can contain PAD1, PADN, Target, Transit
and Target descriptor. Right now we are not skipping PADN and
Target descriptor payload.
Change-Id: I89a9c3cb59de5397d1430f0fa5de95beee193880
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Parse DAO ACK from parent and analyze it.
Change-Id: I2394bd5e339ff00c87b9b4835dd5a21e2bafb2e5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Indentation is wrong for few options. And few options does not
properly aligned.
Change-Id: Ib4a8a90a17fd20ddd16ec6f29558eb937f035bb9
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Earlier net_nbuf_copy() mangled the original buffer. So cacheing
src and dst address was necessary. Now original buffer does not
get affected by net_nbuf_copy() call. Cacheing is not required.
Change-Id: I25f60bc6db2a75612e562e56024d4459478d80b4
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Do not call callback if destination ll address is not set. This
happens when dst is multicast or broadcast.
Change-Id: I34dda92799a987d9cff031dc97f4a01b94437561
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Same volatile status variable as return and being updated
in ISR would modify the variable in two context which
caused the variable to be set to a stale value.
This commit uses two different variables, one for return
value and the other to be updated by ISR.
Jira: ZEP-1941
Change-id: I19e3bdc85e15bda7891395f3f1f64c2ddbeee0c6
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
role_disable initiated through HCI commands are initiated
in thread context and controller code was using the job
mayfly caller id instead of using the correct app caller
id.
Also the XTAL retain calls being called from two different
call context used the same worker caller id and same mayfly
instead of using the correct caller ids and independent
mayfly for each caller.
This potentially could cause mayfly enqueued list to be
corrupted and enqueued mayfly could be lost.
Change-id: Ia356419462d1fb4e38f4a20c720974143f12fdb6
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
There is no transition from tentative state etc... It should directly go
to preferred.
This is fixing ND processing when DAD is disabled: source address was
never set, as tentative state is not a valid in
is_proper_ipv6_address().
Change-Id: I6f0a0fdd99dd13d28849f9749f89ec21fdd370d8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add "net dns <hostname> [A | AAAA]" command support that can be
used to query IPv4 or IPv6 address for a given host name.
Change-Id: I86b2258efa994a67163f9b3b340f44d65767f11b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the config file contains DNS server addresses, then
configure the DNS resolver to use them.
Change-Id: Ie7f2bdcf7ac4bb7ee0ecf7fb5b7bd2df3379cdc3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit introduces a generic DNS resolving API that can
be used by applications. Later commits will introduce a system
level DNS support which simplifies the DNS resolving so that
DNS server names can be given from config file.
Change-Id: I60fbc81e2a44928d2ca53d51e703b9cde222b382
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Length parameter was always useless, only used in debugging, so that can
be removed.
Change-Id: If597f424840f37955202fa5fe827dd992e4cf776
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Thus the ping command is more user-friendly: at least user knows the
ping got a reply or not.
Change-Id: I740a2f77d288f6287ac04c908f3d517a49df57d2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As it is done for ICMPv6. This will prove to be useful for implementing
an echo reply handler in a ping for instance.
Change-Id: I969a1da60f2a4ea59eee5c9983eb6e340923e2ef
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
net_addr_pton always returns -EINVAL in case of error, so let's play with
it to factorize the code.
net_icmpv<4/6>_send_echo_request always returns -EIO in case of error.
Change-Id: I89e5ccd4b936701f7dad194089dda845fab5d738
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Refining the names around IPv6's neighbor states to differentiate them
easily from any net_nbr related names (which are not tighten to IPv6).
Change-Id: Ibc24df2a9485477a53fe5fe1c8f993f0fcd91635
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Probably some refactoring left-over.
Change-Id: I9715441a54b2e675135ce4072651dcead3216d3b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We incorrectly changed the state from FIN_WAIT_1 to CLOSE_WAIT.
This caused ACK be sent in CLOSE_WAIT state when the connection
was closed by peer. Sending ACK in this state is not allowed
according to RFC. The connection was still closed but slightly
wrong way.
Jira: ZEP-1961
Change-Id: Ie4aa6818128d4190230b679e26ac9630c7d45d69
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can open a TCP connection (just one at a time) by
using "tcp connect <ip> port" command.
Data can be sent by "tcp send <data>" command.
Connection can be closed by "tcp close" command.
Change-Id: I75aedd873a30575a6f742926b716afb7dbbfb92b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No functionality changes, use separate variable so that we do
not need to do big-endian conversion multiple times.
Change-Id: I8874b427bd39dfa2d952034a2623c47544a644fc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If IPv6 router is added, then NET_EVENT_IPV6_ROUTER_ADD event
is generated. When router is removed, NET_EVENT_IPV6_ROUTER_DEL
is then generated. This is useful info if we want to have a generic
connectivity to outside of our local network.
Change-Id: Ia03958a071ceb998127894025c99ab72a8b648d5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the bind port is set to 0, then return the real bind port and
show it in the debug print.
Change-Id: If75b52bdacfc916329222d0d9e8aa4669e7a7160
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is part of a patch series to decouple TCP/IP offload, which
currently occurs at the transport layer (L4), from the data link
layer (L2).
- Rename struct net_l2_offload_ip to struct net_offload
- Rename struct field offload_ip to just offload
- Rename include/net/offload_ip.h -> include/net/net_offload.h
Change-Id: I3cd891c2b13e0e8f3ad1c66264f90b5031ae17c2
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This is part of a patch series to decouple TCP/IP offload, which
currently occurs at the transport layer (L4), from the data link
layer (L2).
This patch simply renames the NET_L2_OFFLOAD_IP Kconfig variable
to NET_OFFLOAD.
Change-Id: Ic8b1d004cbac09b7c636475aaed75b0a31e4be1c
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
When route not found try with default router if it exists. Consider
default router as nexthop. If default router also does not exist
then drop the packet.
Change-Id: I56cc9e4a1432fc25687cbaea600bfe9cf5b1d51e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
No memory leak but debug prints shows buffer dropped due to
NET_DROP verdict. Added TODO comments to support DAO ACK.
Change-Id: I32deb2e1d2eea98f19ef26ad429ba8d03ae13751
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When an intermediate node received DAO message, it should forward it
to its parent (if exists) and it ack to orignal DAO sender. But
dao_forward() function steals frag chain from original buffer. Src
and dst address pointers to original buffer are not valid to
continue in dao_ack_send. So cache them for DAO ACK.
Change-Id: I3a4df4837a133afe4e2badb183f729c37d267f63
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When DAO message is required to be forwarding to a parent addr,
only frag chain and iface is considered. But for newly created Tx buf
other metadata also required. In this particular case setting
inet type, ip header length. Also update checksum as dst address
is changed.
Change-Id: If0e0a52e943db66be4aeecb6d0e3b9d7c3f04f58
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Path lifetime exists at 6 byte in RPL Transit information. So after
type and option length 3 bytes should be skipped to read lifetime.
Change-Id: Ic90c3bd75e3c7c63ffe9be27c0d206fc8fd58604
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
NET_RPL_DAO_ACK Kconfig option was missed. subsys/net/ip/rpl.c has
functionality of this option. By default it is disabled. Enable it
if you want to know the status of DAO message.
Change-Id: If5ed86c9c8c6c62991fc92d2f1e2a35331811356
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If DAO message is not inteded to destination node then
intermediate node will forward original message with final
destination address. But verdict not passed properly.
Change-Id: If61c7b683b55b24b68f5235d0eee5ed60b611aef
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Unref the buffer if net_context_sendto() fails to send.
Change-Id: Iaae81f3044ad7197974493018b873bb76b2c0760
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Two size_t variables were printed using %d which gave warning
if RPL debugging was enabled.
Change-Id: I6bc135c76a31da304e94af34ecd571163ddf2a0e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Selecting RPL will need to enable NBR cache support,
it is not enough just to select IPv6.
Change-Id: I8162497111354d0fa9e44564fa5cc5ee46110b96
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of simply dropping the packet if the destination IPv6
address is not ours, try to figure out if there is a route
to real destination and then re-route the IPv6 packet there.
Change-Id: I6b2a0d7096b3d7877b82b04f38e3a6e588587c11
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This avoid having duplicated code for list manipulation in both LE and
BR channels.
Change-Id: I734635e8e51d4b826a3d45cda8551e1e509bd913
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes an issue found on automated testing. If IUT had no credits
to send data, the TX request was not queued, because -EAGAIN error was
not returned to bt_l2cap_chan_send (which was responsible for queueing).
Scenario:
1. IUT was out of credits
2. Tester requested to send some data
3. Credits was given
4. No data was sent
Fixes: ZEP-1896
Change-Id: Ie9d0945d1e6b628cd978ede8105b37b838a61f1a
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
Cleanup controller's root makefile and add folder level
makefile to have better control over dependencies.
Also explicitly include folder paths in c files to clearly
depict the dependencies.
Change-id: Iac7b3a86eff11082111049ba48559c74f6c4d3fb
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move the PDU related size definitions out of radio.h and
place it in pdu.h. This will remove hci's dependency on
radio.h.
Change-id: Idf9d7cdf7c60d74816ef2b093c4ae457df16e9a9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Mark each PDU type explicitly instead of using BT_ATT_OP_CMD_FLAG for
this. For simple "error response or not" selection the command flag is
sufficient, but to prepare for support for enforcing both request and
indication flow control it's useful to easily look up the type of the
PDU.
Additionally, refactor the handler lookup to make the flow a bit more
streamlined.
Change-Id: I575848356934b6d636dcda8d10b7e7fde1095355
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move the uint8_t members together to save 4 bytes for each struct.
Change-Id: I522be86397c57fd062018e409b65835912c6e7bc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
bt_conn_le_param_update returns -EBUSY when used in central
role if peer did not support LE connection parameter
request.
This commit allows a central role to use either LE
connection parameter request, if local controller supports
it, else use LE connection update.
Jira: ZEP-1773
Change-id: I72b9c77440459672fd50216a74ffcbd59c5f38f6
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added checks for latency and timeout changes requested in
bt_conn_le_param_update, to decide if connection parameter
update is needed.
Change-id: I9de9f566158c5ade808ed356cb90b27186aa0243
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
There's no need to be opaque about this. Use the right type and let
the compiler catch errors for incorrect assignments.
Change-Id: If745354f514cbecfe6c0d845ebeaf3b93208b9b8
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Only 1 TX buffer is sub-optimal for performance since the controller
would always have to wait for the host TX thread to give it another
buffer. Increase the value to 2 so the controller can keep
transmitting data without waiting for the host.
Change-Id: I4841a6c5010f294996d6fe0fe63260b848a6a437
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Updated controller code to use NULL keyword instead of
using 0 for pointers.
Change-id: I5ebff53dfeeba670fb7afe4740596b2662eb0334
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
There may be use cases where input and output is in big-endian rather
than little-endian. Introduce a native big-endian API to avoid
excessive byte order reversals in these cases.
Change-Id: Ia7b3e01bb0a07c4560b23f60c2f615ec614eb431
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are some use cases where all parameters are in big-endian. To
avoid excessive byte order reversals introduce a native big-endian
API.
Change-Id: I58fe9156c8819a3a43d715e70b6ba358bd2f844b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Do this in preparation of a purely big-endian API (all three
parameters as big-endian).
Change-Id: I815f74549caffd5ac387b5bb84e5851aa96639b9
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
1. Reset the state when error occurs
2. This patch avoids checking for the AT_STATE_UNSOLICITED_CMD state
as the loop exits with possix error. So check for at->state
AT_STATE_START is sufficient for loop termination.
3. Fix different sign warning.
Change-Id: I80a1ca582112f1783690ac8a4125036bb706705f
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This patch adds support to initiate audio connection from the stack.
< HCI Command: Setup Synchronous... (0x01|0x0028) plen 17 [hci0]
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 7
Setting: 0x0060
Input Coding: Linear
Input Data Format: 2's complement
Input Sample Size: 16-bit
# of bits padding at MSB: 0
Air Coding Format: CVSD
Retransmission effort: Optimize for power consumption (0x01)
Packet type: 0x003e
HV2 may be used
HV3 may be used
EV3 may be used
EV4 may be used
EV5 may be used
Change-Id: I4f4c0788760c9bdaf75651825511ff6bcd06df59
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This patch handles the SCO disconnection part also unref the connected
corresponding ACL conn.
Change-Id: Ic2de68560cfd7d847e6011578c4424e24800d2ac
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This patch renames the 'conn' variable to 'acl' which is reference
to ACL connection for SCO connection.
Change-Id: I5f0a60bc5d80de08fa5b963cf545c71552909401
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Expose LE Encrypt helpers to applications. If software-
based controller is compiled-in, then controller's AES
hardware will be used by the exposed helper interface.
Change-id: I2bac9dfa5ccb3dd50447079affb52d920ae5bd81
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>.
Now that we have all the requested attributes of the service, form
the response packet and send it.
This also renames create_attrib_resp() to create_attrib_list() since
it is basically creating the list of attributes based on the filter.
> ACL Data RX: Handle 256 flags 0x02 dlen 21
Channel: 64 len 17 [PSM 1 mode 0] {chan 0}
SDP: Service Attribute Request (0x04) tid 28258 len 12
Record handle: 0x10000
Max attribute bytes: 4096
Attribute list: [len 5]
Sequence (6) with 3 bytes [8 extra bits] len 5
Unsigned Integer (1) with 2 bytes [0 extra bits] len 3
0x0004
Continuation state: 0
< ACL Data TX: Handle 256 flags 0x00 dlen 32
Channel: 64 len 28 [PSM 1 mode 0] {chan 0}
SDP: Service Attribute Response (0x05) tid 28258 len 23
Attribute bytes: 20
Attribute list: [len 17] {position 0}
Attribute: Protocol Descriptor List (0x0004) [len 2]
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
L2CAP (0x0100)
Sequence (6) with 5 bytes [8 extra bits] len 7
UUID (3) with 2 bytes [0 extra bits] len 3
RFCOMM (0x0003)
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x05
Continuation state: 0
Change-Id: I54ba00f7700cbb72182dce745d61f5281f83437a
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Move crypto related interface provided by the
software-based Controller bt_rand into separate file,
crypto.c.
Change-id: I9998a43fe45799b479969ca195f324199418b8c2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Use explicit path while including internal header files.
Change-id: Ide80eb23007574a7362850173ac227943bda21d5
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The current hci_driver.c contained all the software Link Layer
initialization code. To decouple HCI from the actual LL, most of the
functionality that is actually part of the LL has been moved to the
ll_sw folder, opening the possibility for future hardware-based LL
implementations.
Change-Id: I1b54d655568a4ec02409da2f1a0addb4d64beed0
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since this presents a risk of public Bluetooth address duplication in
the wild by compiling once with a particular address and then flashing
the same image to multiple devices, a decision has been taken to remove
that config option and replace it later with another mechanism.
Change-Id: I068db25b2996c2409630554b1819b6adc48226cd
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To present a common interface to both software and hardware Link Layers
the API in ll.h now lives in its own separate include/ folder.
Change-Id: I2b0ab0d11b47b9c35a5759bcc30f347e6c616648
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Declaring these as const lets the linker generate more optimal code.
Some extra care is needed with hci_ecc.c since it was overwriting the
send callback. Now the choice of send() call is done directly in the
bt_send() function
Change-Id: Iac74f5ee9bee097bbb34c11bd13d1d886700f5cc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Retrieves the record specified by the record handle, go over each
attribute in the record and check whether the attribute is there
in the list provided in the request.
Change-Id: I8f09e0fbb7811a20bb25dc0029cd7c79a9345c88
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
In preparation for future hardware implementations of the BLE
Link Layer, this patch introduces the BLUETOOTH_LL_SW
configuration option to specify that the default software
LL is to be built.
Change-Id: I8b9d5b5e0d2926d18f9e8c8f042a74326895bf95
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Handles the ServiceAttributeRequest, populates the attributes to be
searched in the record specified by the record handle.
Change-Id: I3b702eaf05615f795d32aa30dbfaf91f5b2ce560
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Rename all LL downstream API calls from radio_ to ll_ so that they
reflect the layer they are actually targeting. Additionally they have
been moved to ll.h so as to expose a proper interface.
Change-Id: I4fb3946597920c9fafaacb6d87d34d83d75e8f27
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove the H:4 packet type macros that were unused in this file.
Change-Id: If161ddbf2d3adb2871cadd76de0e6c3bb50a16db
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Report as Bluetooth 5.0 compliant controller as there are
no mandatory features.
Rename PDU types as per the changes in Bluetooth 5.0
Specification.
Change-id: I1363e054eafd37c2bdca0f69b2638c7edb785787
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Bluetooth device address is 48-bit, added Kconfig range
field to restrict input to 48-bit hexadecimal value.
Change-id: I650343eab5809535137e164e783c9dd4f3e2a6f2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig option to set the Controller's company id and
subversion number.
Change-id: I3508aba18bf0b79fd423c7b4142b6fc57eaf55d7
Signed-off-by: Matthias Ringwald <matthias@bluekitchen-gmbh.com>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add a Controller event that indicates everytime
advertisement event has been transmitted on air.
Change-id: I4722488bbfeca987e66983faf5b26467407a89c9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add ARG_UNUSED on rssi_ready local variable when the RSSI
feature is compiled out.
Change-id: I04f8f11cbc3530f7b85ffa72f27373e213b6e35e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Now that we have all the records which has the uuids in the
service serach pattern, take the handle of each of those records,
prepare and send the service search response.
> ACL data: handle 256 flags 0x02 dlen 17
L2CAP(d): cid 0x0040 len 13 [psm 1]
SDP SS Req: tid 0x6b6f len 0x8
pat uuid-16 0x0100 (L2CAP)
max 256
cont 00
< ACL data: handle 256 flags 0x00 dlen 26
L2CAP(d): cid 0x0040 len 22 [psm 1]
SDP SS Rsp: tid 0x6b6f len 0x11
count 3
handles 0x10000 0x10001 0x10002
cont 00
Change-Id: I85ec8ee384d0bf8090265577ec3ef805e75d4766
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
k_delayed_work_init shall only be called once per work and not every
time before as that can trash the workqueue list if the work is pending.
Change-Id: Ib04b6689c59d03328687b0b579e80012dbd2f853
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
k_delayed_work_init shall only be called once per work and not every
time before as that can trash the workqueue list if the work is pending.
Change-Id: I454f40b63133bb7d6239dbe902858932bacfc454
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Print TCP header information in one line as there is really no
need to use multiple lines. Also use debug level when printing
the header info so that it is only seen if debugging is activated.
Change-Id: I27f314ca060239545769dec07148897da3426436
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
k_delayed_work_init shall only be called once per work and not every
time before as that can trash the workqueue list if the work is pending.
Change-Id: Ib6398a6a843dd4d820529487ad76a9dc9d9e152e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to commit 8308b9bd2d ("net/http: Add the HTTP/1.1 API")
every user of CONFIG_HTTP_PARSER would need to add CONFIG_HTTP to
their .conf files. Which is fine for intree samples/tests as they
have been adjusted, but the rest of world working on Zephyr apps
will need to make this changes as well.
Instead, we should have each of the following select HTTP instead of
depend on it, which will make future use of these configs and their
dependencies more intuitive:
HTTP_SERVER
HTTP_CLIENT
HTTP_PARSER
NOTE: As cleanup, this commit also removes the CONFIG_HTTP added to
samples and test .conf files.
Change-Id: I81cfaa19e37333b1bf98778f8147814780e7f77c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This fixes warnings when using %u to print the result of sizeof.
Change-Id: I5391456c855ec2785af22467d9d0f355bbb1e577
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The return code from net_icmpv{4|6}_send_error() was not correct
if the error message could be sent. Now 0 is returned if sending
succeed, and <0 otherwise.
Change-Id: Iff67f097a9d9519c9f11d4cbc9cf428a7c74ec1b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Update statistics for every sent, received and dropped
ICMPv{4|6} packet.
Change-Id: Ibe6f02e8222adb3db1f1dbd0cde1ed251710eb43
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are replying ICMPv{4|6} message, then do not wait forever
for a free buffer. In a busy system, this might lead to non-progress
in RX path if we receive lot of packet from the network and never get
a free buffer.
Change-Id: Iaef92541b8745f872a07bc6e2052d0393d4d1e8b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
commit 2e3e93dccb ("net: 6lo: Fix compress bit calculation") adds
a bit shift to the compress bit calculation, however it's typo'd as
a greater than comparison causing get_6co_compress() to return a
boolean value rather than the shifted version of the calculation.
Change-Id: Idacac2c032a03f1f75a78c94bed4c70428b8c77a
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The IPv6 prefix address length was incorrectly set in net_if
after RA was received from the network. The incorrect "len"
variable was used instead of correct "prefix_len" in the prefix
info struct.
Change-Id: Ifeaf150b9960414d2ad200053a3bd5290dc8d365
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the earlier prefix timeout is not cancelled before setting
it again, the system will hang.
Change-Id: I6e271294c8e5d43e3ceae4780b5d1c26bab2b296
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The caller semaphore was released too early, this can cause the caller
to re-use the data and possibly corrupt the memory, if caller yields
and is run before this management thread. Solution is to first remove
the node from the list and then unlock the semaphore.
Change-Id: I02cef53559d776f32a5959380e6b7122cd5198c5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add CONFIG_NET_IPV6_NBR_CACHE option that is the base for both
neighbor discovery (ND) and duplicate address detection (DAD).
Both ND and DAD can be disabled if needed. If NBR cache is
disabled, then ND and DAD are disabled too.
Note that it makes not much sense to disable DAD or NBR cache
as IPv6 will not work properly without them. It is possible
to disable ND but then the neighbor information needs to come
via other sources like RPL.
Change-Id: I57c8668ad828b3a153dfc58eea78bf5f7ac3938a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Although very unlikely, I saw crashes at startup that could
be because of the buf or iface were null.
Change-Id: I8649eeb4f24fcd7d9f2acaeefaba4e6593388e91
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The fragment pointer is good to print here.
Change-Id: If09e684bbe0f9f5d3f961c4af8f86fb3ff364671
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If for some reason the neighbor solicitation cannot be sent,
then we need to unref the pending packet as that would never
be freed otherwise.
Change-Id: Ied12a9b3a027a2aad3fafd0b5b36c56b5f042c28
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are trying to send a IPv6 network packet and there
is no data, then print error.
Change-Id: Ia0e7bebae513f1bcf984e189566ae7e10a90bbfc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When going through fragments in update_ll_reserve(), use
net_nbuf_unref() in order to get better memory allocation
debug prints.
Change-Id: Ia7ee15b32800acdebeb28125465515132c55e179
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to receive anything if network interface is down.
Change-Id: I22d62aeaf4fbef54608818bf6c8073ec2e9a7c09
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that both the TX and RX threads are running before
we turn the network interface up.
Change-Id: Ie7e5938403e90e1ae76047c221cf9fd2f5a1167b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In case of callback based event listener, it is easy for the callback to
filter on the given interface. But in case of the synchronous call it's
not: it would need, after a failed comparison on the interface pointer
to loop by itself on the net_mgmt_event_wait() which is a little bit
heavy (reinstalling the event listener, with the semaphore and all) and
a bit of a burden for the caller itself.
Instead, net_mgmt provides a dedicated call
net_mgmt_event_wait_on_iface() which does it the right way, so the
callback and the related semaphore are destroyed if only the iface
matches the one given as parameter (besides the timeout obviously).
Change-Id: Iab05c3249586f4f4d0447eea42fdac72b8428f2e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of creating a handler and a related callback structure on an
event_mask: net_mgmt_event_wait() can be used to wait synchronously on
such event_mask. The core mgmt part will seamlessly reuse the struct
net_mgmt_event_callback so the whole internal notification mechanism is
using the same code.
Change-Id: I426d782c770e75e5222aa3c5b703172b1f1f2e5e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's not enough to know just network address and port number to
disambiguate an endpoint, protocol (TCP vs UDP, etc.) should be
known too. Without this patch, there is a confusing output from
e.g. echo_server if both TCP and UDP is enabled.
Jira: ZEP-1086
Change-Id: I247a2dfc87df634ceac3b8733d7349b1d6aca80c
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This function is useful for logging in other parts of network stack,
so allow to reuse it. (Will be used for net_context logging in a
follow-up patch).
Change-Id: I8238874584f8f039c94e5d827265944d97d13f6b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
NET_IF_UP may change during the lifetime of k_pool which means we would
have to reconfigure everytime the flag changes but NET_IF_UP is already
checked during net_if_send_data thus it should never reach the queue in
the first place making this check unnecessary.
Jira: ZEP-1888
Change-Id: Iaa8471bee886a6f7e701a1dd243fb199def26589
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current finalize api's takes buf as input parameter and returns
the finalized buf. But if there are any issue while finalizing,
it failed to throw an error.
Change-Id: I6db54b7453eec41a8051fab50d5c0dc937debd54
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When IPv6 header contains extra header (e.g. HBH), extra header length
was not part of app data length calculation. Result applications get
invalid total length. Also simplified set_appdata_values().
Change-Id: I07438d62dfd0f9abc1452484deb8b5eacdc37cf1
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add support for adding IPv6 extra header (HBH) with RPL options
in ICMPv6 echo reply.
Change-Id: Ibd0b96362a7d5a5f668a18d6a33e6917d37dc51c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
As per RFC 6775 4.2, context length holds number of leading bits
in the Context Prefix field that are valid. Rest are not valid
for compression.
Change-Id: Id21cc2d7a5d42980cf9295f85e75c4869ff6cb99
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When a nodes receive a packet with RPL option in IPv6 HBH, it's need
to be reverted with node flags, instance id and sender rank.
Change-Id: Ic49c8e84c7846dc02728c120078506f6d7411e52
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
RPL extension header verify function takes input parameter as
metadata 'buf' and start reading from it. Instead it should start
reading from fragment (buf->frags). Also API should return
fragment and offset where caller can continue reading it.
Change-Id: I80612144aed55aa2dcf9eaab1f4408e10efdda31
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Make sure the neighbor cache is printed nicely in table
format with columns aligned.
Change-Id: I5323fdc644317ea08fd4694215f8cd44f8d7ff74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use dns_answer_type instead of dns_response_type to reflect that
the routine refers to the DNS answer RR.
Change-Id: I6d01add4a1b090b83a0708326a52b7bb945c8d23
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The net_byte_to_hex() prototype first parameter was uint8_t *,
but it should have been char *.
Jira: ZEP-1885
Change-Id: I6132a67bb9e8199de88451fb4e446081f401e8f6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We did not handle NUD (Neighbor Unreachability Detection)
properly and did not go to DELAY state when neighbor
reachability was checked.
Change-Id: I127d25124aa806c44ff37c1355cc3db7fb25b2d2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print timer information when creating and expiring the
reachability timer.
Change-Id: I5c8fee91de85fe7c9ea7c467f45dbb105250d5b1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The send_ns timer was used instead of reachable timer when
the reachability timer was expired. This meant that the
reachability timer was never restarted after it expired once.
Change-Id: Iccbd6d019d1106adca60f7319bc4c547cdb1d924
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print the neighbor pointer address and remaining time when
viewing the neighbor cache in "net nbr" command.
Change-Id: I13840ccc16c31c99a803ec1b7afe69879bd639f2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use the proper API to get the remaining time in prefix timer
and return the value in seconds as expected.
Change-Id: I055ce0ba6092c23ad60d6775ce75a0a67ad91d26
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to verify that the neighbor is reachable, send
neighbor solicitation message to neighbor which should then
send neighbor advertisement to us so that we can then mark
it reachable.
Change-Id: I2c45ee4a6982c698ef6c8fa1acccb995aadf8ee6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to be able to debug IPv6 neighbor state changes,
pretty print the state names when setting the new state.
Change-Id: I64e0b4173eaa63c9715c17420a008602759aa4fa
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
To be used by net-shell and other files for debugging neighbor
state.
Change-Id: Ie9b09a54a05dcb066906a3697dfe38aeffc886e6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "null terminator" for the chunked transfer encoding must be
added only if the payload is present.
Change-Id: Id325a660f060b3a3468bcca16a079def11b8c3ef
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
No need to print error if we have already joined a pre-defined
multicast group.
Change-Id: I1237d5fbf0b63267ccb00432522513358c48d31d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Wrong type modifier %zu in debug print, should be %d.
Change-Id: I82feca91d9e083a03263477569c552acc7c9767f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Patch 235118245864491a592245f57e5244bf61711943 did not set the ll
addresses in the right buffer which causes 6lo to unref buffers
causing a double unref latter.
Jira: ZEP-1890
Change-Id: Id7591ef3c20c7ab62dcb04576406d70602baa129
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
IPv6 fills in lladdr_dst properly according to nexthop. Thus it's
useless to lookup again for nbr when creating data frame etc... Let's
use this directly. It both optimizes the code path as well as implements
proper nexthop frame sending.
Jira: ZEP-1863
Change-Id: Ic17a1b14a0db0692d31419ea2f45a5f288a09fb5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This patch adds the HTTP/1.1 API for Zephyr. This API consists of client
and server context structures enabled via Kconfig variables.
HTTP parser support is enabled via the CONFIG_HTTP_PARSER configuration
variable.
Currently, this API only includes support for writing HTTP requests
(client mode) and HTTP responses (server mode). TLS support is not
considered in this iteration.
Supported HTTP methods:
GET, HEAD, OPTIONS and POST.
Supported HTTP responses:
400, 403 404. The http_response routine may be used to write
any HTTP status code, for example 200 OK.
Jira: ZEP-1701
Change-Id: Ic9ccd4d4578d6d0f3a439976ea332b031644ca7d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Now that k_poll landed in the kernel, it's worth using it to save
memory and reduce the number of threads at runtime.
Such switch has been first done in bluetooth (see hci_core.c and conn.c
in subsys/bluetooth/host). Since network interfaces kind of follows the
same design for sending data, it was then easy to copy the same change as
in bluetooth.
Change-Id: I7f9734b88ac818284bbabaedc946b4765b905ebb
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Due to recent TCP fixes for 6lo, we are making a copy of buffers
sent to net_tcp_send_buf() so that TCP retransmit can send the original
(unmodified) buffer. This original buffer is freed via the TCP
sent_list when the related ACK packet is received.
However, there are users of the net_tcp_send_buf() function which
will never get a corresponding ACK (and do not add the buffer to the
TCP sent_list). An example is send_ack() in net_context.c. In this
case, we leak the original buffer.
To fix this leak in the 6lo specific block of net_tcp_send_buf(),
let's check to see if the original buffer was added to the TCP sent_list
and if not, then avoid the buffer copy process entirely.
Change-Id: If99e0e5bf266d33dd3466dc5d74443eaa39d10a8
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The static keyword is missing in the dns_find_null function definition.
Change-Id: I19c89ca61b6ff550bf7ccb2ca9065a957532ede1
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Don't break the line after the static keyword.
Change-Id: I51343124ae3b3a2f9b4916c5279ba09b8c08fd9a
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Instead of magic constant (0) use the K_NO_WAIT when spawning
a thread.
Change-Id: Ib3a181fdfa246843d9c708592ccc754e54bc6005
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the networking cannot work without RX or TX threads, mark
them as essential.
Change-Id: Icb52c77fcdcef35d77c36e5ec855fed438a38407
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we cannot join pre-defined allnodes or solicit node multicast
groups, then print error. Typically this will happen if the number
of multicast IPv6 address records is too small in net_if struct.
Change-Id: I12211cff90ef4edc856f1432cab0c37aae9a1bd5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is only needed when doing unit tests.
Change-Id: Ifd4e5e8ea98e3ab2344ed0c19d92f2be7d8008f8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Collect number of received, sent or dropped multicast listener
reports and queries.
Change-Id: Ia5c08203155475763f96df23f44eceffa7569873
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive MLDv2 (Multicast Listener Discover) query,
we send out information about the multicast groups that
we have joined.
Change-Id: If4ea9fa685319b2ad900e1949a5cbe12e7696b43
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As dictated by RFC 3810 ch 5, we need to add Hop-by-Hop option
with Router Alert sub-option to the sent multicast listener
message.
Change-Id: I8e3ed58fff4736e9708276a3185f94e7f2b453a3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are taking network interface down, then flush the TX for any
pending bufs that would be needed to be sent.
Change-Id: I229ecce8e07ec5847d4c6c6a1994de04bd9171e2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the multicast address already exists, then do not give
error but try to join it.
Change-Id: I32ffa6b3bf0798011d684a1a21e87e389f1f0380
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When network interface is taken down, leave only those
IPv6 multicast groups that were joined.
Change-Id: I414556c093ba67be7c13e6c86e0451465c2203f3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Send management event if we joined or leaved IPv6 multicast
group.
Change-Id: Ieeb407ef88fb3bf4cd92d4fb4b69f03b260474e7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When we setup the network interface, add predefined IPv6 multicast
groups into the network interface. When interface is taken down,
then leave all the multicast groups that joined.
See RFC 4291 ch 2.8 for details.
Change-Id: If17d3e8c75157a02aa93c92e2fb499619c1484cf
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This and subsequent commits adds API to join or leave
an IPv6 multicast group.
Jira: ZEP-1673
Change-Id: I26dcfe16a4527dbf7886a30827a5d4ebfdeaac01
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The tcphdr->offset was not set when tcp options were added.
Change-Id: I19fe97983ce81948a9a84893183e5c9000f12767
Signed-off-by: june li <junelizh@foxmail.com>
There are no users of net_tcp_set_state() left outside of
subsys/net/ip/tcp.c.
And the naming of this function is confusing -- it could easily
be mistaken for net_tcp_change_state() which contains additional
logic for certain tcp states.
Let's remove it entirely and fix the remaining uses to set
tcp->state directly.
Change-Id: I92855ad180e8682780fcff11e50af06adcbc177c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In net_tcp_release() when a TCP connection is being closed, we
should call net_tcp_change_state instead of net_tcp_set_state.
net_tcp_change_state() will call into net_tcp_set_state() but
also contains logic specific to NET_TCP_CLOSED which unregisters
the context's conn_handler and sends an accept callback (if
present) with -ENETRESET error for user code to handle.
This fixes an EISCONN error returned by net_context_bind() when
a TCP-based net_context was reused. Due to the conn_handler
not being cleaned up in the TCP code.
Change-Id: I8439a028a1c7ae5fd2a50d11caa9947a0ac6c7d4
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The parsing of IPv6 extension headers was skipping bytes
in certain cases.
Change-Id: I80612144aed55aa2dcf9eaab1f4408e10ef9ca31
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Compress bit calculation was wrong. It should be moved
to 4 bits left to cache it properly.
Change-Id: Ib011874881a69032795c2ecfd9a615b6cf559c69
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Max 6lowpan contexts are 16 as per RFC 6775 4.2 6LoWPAN Context Option.
Range is 0 - F. So context id '0' is valid.
Change-Id: I8468a805e0145b64921139a587cdaeeb9d6871b8
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If hoplimit bit is unset then values are inlined as
per RFC 6282 3.1.1 HLIM: Hop Limit.
Change-Id: I5821fdf1a4a65b252362277cc604ae913203f80e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Hop limit compression should be after next header compression as
per RFC 6282 3.1.1.
Change-Id: I0eaf3428bf835fe73831a7fe6fb708b73c8f5d12
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_nbuf_ll_src(buf)->addr and net_nbuf_ll_dst(buf)->addr should be
pointing to ctxt area not actual net_nbuf_ll region since the payload
over Bluetooth does not carry any ll addresses.
Change-Id: I87828d74abf2402fdf2a5e34aa8db93aa7c50d08
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the packet contains IPv6 header + Extra header + ICMPv6 headers,
last header does not contain 'next header and length' fields. So
while parsing header we should first check next header and continue
parsing. Otherwise we parse 2 bytes extra and set invalid ext hdr len
and handover to other layers. So everything goes wrong after that.
Also simplified next header parsing to minimal.
Change-Id: I5d8235c5a57c8b77adf6a07eb8eb74350a3e4dc6
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If the buffer contains IPv6 header, set header length only once.
Need not to set it in different scenarios.
Change-Id: I54ab9a4259851c9230db240f6091e3190d25b6cb
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If RPL is not enabled do not handle RPL options in IPv6 extra header.
Issues will arise if we skip reading those bytes and continue further.
E.g. Upper layer protocol like ICMPv6 echo request does not prepare
proper echo reply if we skip like this. It doesn't know what options
need to be updated in reply header.
Change-Id: I250672a54d4c7f60727313f6e7f8fe902685d0c5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Verdict not assgined to its proper value and return NULL in case
of read error. Also simplified error handling.
Change-Id: Idf4c5e242066dfd03e1519271dc1ba38ec43e6ce
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Verdict NET_DROP returned even though it handled properly.
Change-Id: I61e04b12f971b39585e983aa9a1007c63acd8b4e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Debugging code snippet inside handle_echo_reply() does not look nice,
just provided inline functions and simplified it.
Change-Id: Idc3a9284153aaa04d0431a9dd705c4f1c51b817d
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Earlier net_nbuf_copy_all() mangled the original buffer. So cacheing
src and dst address and other values was necessary. Now original
buffer does not get affected by net_nbuf_copy_all() call. Cacheing
is not required.
Change-Id: I8a8534f7ec299853b9b296d85e8aacecd3768c8e
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Variable len is not used in net_icmpv6_input() and if required
it can be obtained from 'buf'.
Change-Id: I4b0710e1cf16cff9837173ad9d6908ec54ebafae
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
TCP support is already implemented so it can be removed from
TODO file.
Change-Id: I27690120959ffa1e15891e3210bbcc38a3898359
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
If a UDP context had net_context_recv() called before
net_context_bind(), then it will have a stale connection handle
associated with initial (random) port number, while will be "bound"
to a new port as specified in net_context_bind(). So, it silently
won't behave as a user expects. net_context_bind() should really
update (or destroy/recreate) conn_handle in this case, but until
it's implemented, apply stopgap measure of at lease reporting error
back to user in this case.
Jira: ZEP-1644
Change-Id: I22ad55f94eaac487a4d5091ccbb24f973ec71553
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Print information who freed the net_buf last time if this
can be figured out. This info is not fully accurate if there
is lot of allocations going on but could give some indicatation
who was using the net_buf previously.
Change-Id: I3d4463c54a9b944847a532d951fb6d2303fc06cf
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we could not allocate a buffer while unfragmenting, make sure
that all the created temporary net_buf artifacts are freed and
we do not have a memory leak.
Change-Id: Ib98ae32eb4a0f9b5f92c51e9713fd8e6d78b10da
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
It is possible that the cached buf is NULL so avoid nasty
error print by not trying to free NULL pointer.
Change-Id: Iec53164f6ffab4b830aba63a1f351ca2349a43ff
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If net_nbuf_read() or net_nbuf_write() offset adjustment fails,
print the offset value in order to make debugging easier.
Change-Id: I899998bdcbc91a25ed7d71a599a5052a6fa4ee36
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Show only what would be freed when debugging the allocations.
Let the net_buf_unref() to delete the individual fragments.
Change-Id: I1a39a553f12d73b78c4ba08be0e8e8252b666c8e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net stacks" command will also print main and interrupt
handler stack sizes.
Change-Id: I1b867be81ac8b4f6d9446f484ebb8b1d852b98b0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create net_nbuf_frag_del() so that we can track net_buf frees.
If CONFIG_NET_DEBUG_NET_BUF is not defined, then this new function
will call net_buf_frag_del() directly, and if not, then it will
track memory usage.
Change-Id: I5f382436cebc71fdaf12baf7bf964fb63bee7aca
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds "net allocs" command that can be used to
track net_buf allocations that are done by net_nbuf_get*()
and net_nbuf_unref().
Change-Id: If3dc2ecf5552f8008138ee9733458a19f9764c13
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can track memory allocations and deallocations.
This is enabled by CONFIG_NET_DEBUG_NET_BUF option.
Change-Id: I9d83b9b63fb2b141c9a283887f1770bb4232f61c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to set the buf to NULL as it will get its value
from net_buf_alloc() call anyway.
Change-Id: Ib3a32b6e4cb4b446761b6a97a88c20fc52d3d683
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add description what happens if NET_DROP is returned from
L2 send function.
Change-Id: I371de725b710041bb26a141f9860c0062fb1ef5d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always calling net_nbuf_get_reserve_tx() with zero
ll_reserve (first parameter) and then setting the link layer
reserve separately, pass the reserve to that function which can
then set the ll_reserve in buf itself.
Change-Id: I21c14cb7e2e6c36d170c09998bca0207ecf65c75
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The ll_reserve parameter is useless in net_ipv{4|6}_create_raw()
function as the reserve information is already stored in buf.
Change-Id: I7815a78c001e3da532478c04b3dac9b37bbc723c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code used net_nbuf_get_reserve_{rx|tx}_data() function to
allocate a fragment. Instead of that low level function, use
net_nbuf_get_frag() instead. There are few places this is not
possible or is too big change like in few test programs.
Change-Id: Ied7e2b7db352de998b200ffa6ff82471bfa5ebe3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_buf pool address is not very useful so print the
user friendly name of the pool instead.
Change-Id: I1c64621c816832d2459819490ec5609f5c39f9f1
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The columns were not aligned properly.
Change-Id: I551d04182c2877a29bb02a9da5400d74a080a1c9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not shortcut the sending side for TCP as we need to use
net_tcp_send_data() to send TCP data in order not to have
double unref in Bluetooth or IEEE 802.15.4 technologies which
has a special TCP packet sending logic.
Change-Id: I077db336c6335ccdbbafa4600f98388ecf33955f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When sending TCP data using 802.15.4 or Bluetooth technologies,
the 6lo code modified the original IPv6 header. This caused
issue when acknowledgment was waited to the sent packet as
the code could never match the sequence and ack numbers in
TCP header.
This commit changes this and the packet is cloned when sending
it so the 6lo code will modify a copy of the data and will not
touch the original packet.
JIRA: ZEP-1719
Change-Id: Iae51f35d5b5ada0d2543b58a29abbf10f146777e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Enhance the connection debugging and print the UDP and TCP
checksum when the packet is received.
Change-Id: I1ccf58a299178277fab0667b01d54ad7bac38663
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If there is lot of network traffic, it is possible that all the
network packets are allocated by network driver. The device driver
places the received packets into RX queue. Then that queue is read
by 6lo code. During the uncompression, the 6lo code tries allocate
net_buf in order to place proper IPv6 header into it.
If all the data fragments are in use at this point, then 6lo cannot
continue and it blocks while waiting available net_buf. This leads
to deadlock in the stack.
The solution is to change the 6lo to allocate the net_buf using a
timeout which will cause the received packet to be dropped if it
cannot be uncompressed because of out-of-buf situation.
Change-Id: I137f02b05193e16c45da8804974d357c920c861d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When doing 6lo compression or 802.15.4 fragmentation,
use the API that uses dedicated net_buf pool if that
support is enabled by the user.
Change-Id: Ic6651c393832c759eebb66a41db31c9067ebb4a9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It makes no sense to modify the original net_buf so change the
copy function not to touch the original buffer.
Change-Id: I5d22445ce50cee62994c36567f0e995a500cb89d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The first parameter of net_nbuf_copy() must be the head
of the buffer chain i.e., it must contain the user_data
part. If a fragment is given, then we do not know enough
information to allocate the data fragments.
Change-Id: I052b183d8c63d7326b320254f36f00b2fc48b0a0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Print information about various network buffer pools in the
system. This is useful in debugging the buffer allocations.
Change-Id: I31123c6f1f6647f77503f32e268c174330762128
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can configure its own pools for data that needs to
be transmitted out (TX). This helps to avoid deadlocking
the system if user space application uses all the buffers
in the system, and the core IP stack tries to get buffer
that needs to be sent out.
By default the net_buf pool support in net_context is turned
off as application developer needs to create the pools and
tie them to desired contexts.
Change-Id: Ida4a1771d34d6c250974e56fba4f0e0b2592cb29
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the pool contains now more accounting information, there is
no need to keep track of this data in nbuf.c.
Change-Id: I7fd44f9feda8fd9816356556d1e788ad56e6eedd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adding this information to the pool:
* number of available (free) buffers in pool
* total size of the pool in bytes
This can be used when debugging net_buf pool allocations.
Change-Id: I4212fcddb1affdf53e0827c88473d3380e2a4929
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Rewrite the dhcpv4_t1_timeout() handler to explicitly handle all
states.
Change-Id: I6f9d6c8cfacd945e24eb66c6440bf305d528c521
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The iface handle checks in the both timeout handlers are unnecessary.
Drop them.
Change-Id: Ie7c884b2ea648f700fbefa8382341036a4db063f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Correct the logic that determines when CIADDR is set and when it is
left as all zeros. RFC2131 requires that CIADDR is only set when the
client is in specific states.
Change-Id: I93a45e355fbef8d11dba5ac194570b87c594656e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
RFC2131 places explict requirements on a client w.r.t which messages
are broadcast and which are unicast directly to a server. Notable
rules as they apply to the current dhcpv4 implementation are that
DISCOVER and a REQUEST in response to an OFFER are broadcast. A
REQUEST in state RENEWAL is unicast. There are further rules relevant
to the REBINDING state which is not yet implementated.
Adjust the current implementation that always uses broadcast to use
unicast as required by RFC2131
Change-Id: I6edef4241bcd74623a804a73415888cd679888d0
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
RFC2131 requries that a client MUST NOT include server identifier in
DHCPREQUEST from state RENEWING.
Change-Id: I0fba703f3a3b218af1ac03f4f1f0daa290bd428f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The DHCPv4 client obtains resources from the server on a lease. Once
a lease expires those resources must be relinquished.
Update the DHCPv4 client to explicitly remove leased resources from
the network stack once a lease has expired.
Change-Id: I5d3b7a02e463041cfdee1d104f5962498bdd6a30
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The existing dhcpv4 initialization code places all initialization in
the per iface dhcpv4_start() code. The net_udp_register() setup needs
to happen once for the dhcpv4 instance rather than once per iface.
Subsequent patches in this series also need a place to perform one
time initialization, independent of iface.
Factor the one time setup code out of the existing net_dhcpv4_start()
into a dhcpv4_init() function. Rather than use SYS_INIT() to run
dhcpv_init() we hook directly into net_init().
The prototype of dhcpv4_init() is shared within the net subsystem with
a new private header file deliberately to avoid exposing the function
via the public API in include/net/dhcpv4.h
Change-Id: I3502a53cc3bfe4db4e4cd22c02ae133c266fdf10
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Factor out common code associated with entering the REQUESTING state.
Change-Id: I0fc038a49309625c24b874dfda0355794cd41da9
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Factor out common code associated with entering the SELECTING state.
Change-Id: If34929e5f13dff7650388a2b491a01cbbf5dc100
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Refactor send_discover() to provide a clean separation between state
machine and action.
Change-Id: I96510cc6a7ab16216821fe65ea4289a78f6443aa
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Refactor send_request() to provide a clean separation between state
machine and action.
Change-Id: If4c61c5789c919ab3ce6c1f914afc243176760d8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Split handle_reply into distinct state machine and actions.
Change-Id: Ib177c7a4007662f941f156acfa5791e1d27e3d73
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The dhcpv4 state machine implementation names differ from the names
used by the relevant rfc. There is no good reason for them to be
different, so rename them.
Change-Id: I837f1bc4788c0ed4d2949b12eb6f5bfeef9a0be8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
There are two implementations of dhcpv4 state name numbers to human
readable strings, unify the two.
Change-Id: I1d654918bb919108a0d8c5514b309b193c9c3f96
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The dhcpv4 state machine has a dedicated context within each net_if
structure. For reasons unknown the timers used by the dhcpv4 state
machine have been placed in net_if outside of the dhcpv4 context area.
Relocate them into the dhcpv4 context.
Change-Id: I0531f493610dffda9ca9208993597a5665bde997
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Change the message type representation from integer to enum, this will
help prevent re-occurrence of recent issues where states and events
are interchanged by making it more likely the compiler will see a type
mismatch.
Change-Id: Ia235afda428a9e5dfbd933e02beeae468b4c84a2
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Refactor and simplify packet construction. This resulting code is
simplier, easier to read and compiles a lot smaller.
Change-Id: I43c67d79fbb77f85af54355eca41f516054cbba3
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This function is used only within net_context.c, make the symbol static
then.
Change-Id: Ib2c00a21c25e8c6a1404d6345d4b8ae05b779525
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
'query->value' is a 'const uint8_t *' so it should be casted to a
char (signed) array before it is used in places where a 'char *'
is expected, strncmp() is an example.
Jira: ZEP-1810
Change-Id: I94cf780a40ad5fed29607d2302dc7a10387bb86f
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Since we try to match with POSIX behavior as much as possible, let's
not bother the user unless they need to be bothered. The recv(2) POSIX
syscall won't return 0 on stream sockets unless the connection has been
closed by the peer; however, that was happening with the callback set
by net_context_recv().
Change it so that the callback is never called if operating on a stream
socket and appdatalen is set to 0.
This is similar to a previous patch sent by Michael Scott in [1], but
not relying on the actual TCP flags: only on the appdatalen and the
socket type.
[1] https://gerrit.zephyrproject.org/r/#/c/9949/
Jira: ZEP-1632
Change-Id: Ib0c214fc9269d305a03e8d85eb606f106c45b038
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
From the response of read_local_supported_feaatures check if local
device supports eSCO packet type and update it to bt_dev.
Also added sco field in bt_dev
Change-Id: If85b3d24d327a6243318fad89a07375a8253f89b
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This patch includes handling AG network error i.e +CME ERROR and
report the error number.
Change-Id: I19a3158e44568ad0ad21fb0dd790ac2f554c0625
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
If mayfly enable is called before mayfly could be disabled,
then enable shall supercede disabling, the mayfly will
remain enabled. Any new mayfly enqueued by the caller that
tried to disable mayfly will be chain for deferred
executon under this condition.
The BLE Controller's connection update procedure broke when
mayfly implementation was updated to defer disabling until
all queued mayfly where completed. Mayfly is disabled
between ticker_stop and ticker_start calls to chain them
so that ticker does not power off counter h/w if the ticker
being stopped is last one.
This commit fixes the connection update procedure which
used the mayfly enable before mayfly disable could
complete.
Jira: ZEP-1839
Change-id: I07d34c90d193b5eca9762acd8b7272e8d7a78474
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Call to ticker_stop/update can fail under the condition
where in a role is being stopped but at the same time it is
preempted by the role event that also uses ticker_stop/
update.
Also if a role closes graceful while it is being stopped,
the radio ISR will process the stop state with no active
role at that instance in time. In this case just reset the
state to none, the role has already been gracefully closed
before this ISR execution. The above applies to aborting a
role event too.
This commit adds code to detect these conditions and
deterministically recover from it.
This commit fixes the assert observed while stopping
advertiser in the Bluetooth sample scan_adv.
Jira: ZEP-1852
Change-id: I51c8d6e212ef43e3526a199cf7b666a79729c732
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added Kconfig option to be able set public address. Seems
conformance testers look for valid public address.
Change-Id: I2c4f702117f99a42c9eef0133b46556a1c6d1496
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This allows to queue buffer to sent later in case it runs out of
credits so it no longer blocks the caller thread.
Jira: ZEP-1776
Change-Id: Ifa9b412f98889b50c0b889655d910520d11a4718
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This moves necessary functions that will be needed for queuing packets
while waiting for more credits.
Jira: ZEP-1776
Change-Id: I030c696d432ec5be1b8e6b649e953da145929777
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Controller asserted in preparation of a role event due to
the previous (same or another) role event preparation being
not complete.
Mayfly callee was disabled in the previous event due to the
preparation time being short and previous start running
(higher natural priority) before all previous preparation
mayfly completed. The previous start disabled mayfly to
avoid Radio ISR latencies.
The current role event that asserted, preempted the
previous role (observer role with continuous scanning
window) which runs until preemption to maximise the Radio
h/w use (observer scanning until next interval). The
previous preparation mayfly is still disabled when the
current role preparation tries to use same mayfly instance
which should be free for a new enqueue.
This commit updates mayfly implementation so that mayfly
callee is disabled only after all enqueued mayfly instances
are run to completion.
Jira: ZEP-1839
Change-id: I3e0d31422db8e47b819189110b11ebd07dd09a7c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The 100ms limit is only valid for controllers before version 5.0. For
a 5.0 controller the minimum is 20ms (0x00a0) which is already checked
for later in the valid_adv_param() function.
Change-Id: I0566a38ff855800d2e46e1d2c0a5c7bc9bc610cd
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since there are no mandatory features in 5.0 when compared to a 4.2
compliant controller, report 5.0 as the current specification
implemented by the controller, to allow for features such as short
advertising intervals (< 100ms) which are already supported.
Change-Id: I1b138a86290a0422760a5e265cdd7b72d68f0048
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for detecting version 5.0, i.e. 0x09.
Change-Id: Ia2da513b65c420142fe97a4fa173bfa8045e9d75
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Filters the service records by going through all the records and
removes the one which does not have the uuid. So finally, only
the records which has all the uuids in the service search pattern
will be present in matching recs.
Change-Id: I1daa7c1b645efae2af66962999cc4c541891eff7
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
bt_gatt_get_mtu can be useful when GATT is used to transport another
protocol on top.
Change-Id: I328ef49138ccc4ce642b0019d08060f6022d5aa7
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Handles the service search request from peer, parses the service
search pattern (which is a data elem seq of uuids to be searched)
and populate the uuids.
This also populates the registered records which will be filtered
based on the uuids in the pattern (which will be done in the subsequent
patch).
Change-Id: I9a232a7cfdd159325214ed13e98cc20be39a2e3b
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
This is mainly done to avoid VLAs for looking up the service to handle
service search requests so that we can make sure that RX stack size
is sufficient for the defined no of services.
Change-Id: Ia99072615d9094a35bd7605ed2901e8018c0ecb2
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Instead of returning -EINVAL at runtime assert in case of invalid
parameters.
Change-Id: I40505f06a4c12445bfb1f1846ace1b592b6bc342
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Separate out data element structure header into type and size fields
Change-Id: I869ee1ea82db1f6d669bb905055135b7d63f3fa2
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
L2CAP TX and RX MTUs will be exchanged during configuration req/rsp.
It should not be modified after connection.
Change-Id: I1e291c9e093561f349bcdcbb75cd7ff22b4163a5
Signed-off-by: Kaustav Dey Biswas <kaustav.d.biswas@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
A new Kconfig debug option now controls the usage of pin toggling to
debug the BLE controller.
Change-Id: I24c5c13ca71e3395e10f14e27ad4bca9f2e94687
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use macros to identify the different debug pins used to monitor the
runtime behavior of the controller, for easier identification of the
lines.
Change-Id: Ia76d6298985b1d367b7ad193d8261f5403446371
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added an API to allow addition of stream end points by the application.
Change-Id: I91b95fc5dc3b9b2950e8d55b5846e460e55f2453
Signed-off-by: Piyush Itankar <piyush.t.itankar@intel.com>
It was observed that due to possible CRC errors, one
connection interval was not sufficient by the peer to
respond to LE Ping PDU which caused the Controller to
generate the Authenticated Payload Timeout event to host.
This fix advanced the dispatch of LE Ping PDU by 6
connection intervals that the peer would listen to before
the 30s timeout.
Change-id: I6c292c623047a05b4e771e70093d87228db62cce
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The new hard real-time (direct) interrupt support is used
only for Radio IRQ. Only Radio ISR has hard real-time
requirement of completing its execution inside the tIFS of
150us.
This commit reverts back RTC0 and SWI4 ISR to using the
normal IRQ_CONNECT.
Observed on nRF51, Radio ISR (open text, notifications):
Latencies: min. of 5us and max. of 10us.
CPU utilized: min. of 44us and max. of 77us.
Observed on nRF51, Radio ISR (LESC, fast encrypted,
notifications):
Latencies: min. of 5us and max. of 10us.
CPU utilized: min. of 39us and max. of 112us.
Jira: ZEP-1038
Change-id: Id3d09df7bdbdfea090f21f6f58aaded8c5f1e10d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The new hard real-time (direct) interrupt support in the kernel allows
ISRs to be run directly with no significant latency overhead.
Use this new mechanism to improve the latency of the 3 critical
interrupts in the controller: radio, RTC0 and SWI4.
Jira: ZEP-1038
Change-Id: Ief9dacbea4c4c2e8a1c77893a0d6175a91819ffb
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This fix not removing subscription if it was first element on the list.
In that case prev was NULL resulting in passing garbage node to
sys_slist_remove.
Change-Id: I9452af08409692f9a331afd514fbac8cc727d289
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
This fix legacy pairing with passkey entry model when passkey
is fisr entered on local side. Replying with error in that case
is bogus as we should just wait for remote confirm.
Change-Id: I75480802928fd29d21617aa9250f90df647eb9a2
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
This was flagged by ISSM icx compiler.
JIRA: ZEP-1806
Change-Id: Iebd04febbdce9b92a4d0cae986ca7f84f4da58a0
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
If the DAD timeouts, then the pending pointer will be null
when we remove the neighbor. Fortunately this only prints
this error message and does not cause any issues in the code.
[net/nbuf] [DBG] net_nbuf_unref_debug: (0x00118350): *** ERROR *** \
buf 0x00000000 (nbr_clear_ns_pending():175)
Change-Id: I3e11d4aa1d90f205df591b5d5cdcf2ee7bde6c01
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is possible that the buffer waiting for retransmission is modified
after it is sent, for example, it can be compacted by 6lo, and our
assumption of where is the message ID is located in the buffer is no
longer valid.
As the message ID is the only information that is necessary for
keeping track of retransmissions, we keep a copy of it in the pending
struct, as well as the destination address of the retransmission.
Change-Id: Id33d54353404628673541225a1a05e27ee08765f
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When we do DAD (Duplicate Address Detection), the local IPv6
address gets added to the neighbor cache. This is useless so
remove it after DAD has finished.
Change-Id: I9625d367e96d8108a7d3d1d8b2e95f3c4ea11c45
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add net_ipv6_nbr_rm() utility function that can be used to
remove an IPv6 neighbor from the cache.
Change-Id: I9794856a4f65c5e943656970648e5c5762b0338c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add utility function to go through all the stored neighbors
in the IPv6 neighbor cache.
Change-Id: I42fe0ec48c000215403aef63629d0763189ebdbb
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The sequence and identifier fields are 16-bit instead of 32-bit
long. This did not cause any issue in Echo-Reply but those two
fields should be set properly.
Change-Id: I5e4878f53d6bb37660d46d173159d27bbe0e94dc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
TCP header was not sent back to originator when ICMPv6
error message was prepared to be sent.
Change-Id: I171bd724c4260b83d7d1c37e0894f9ed8cddd2c9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to see who is freeing the fragment, add function
and line information to net_buf_frag_del() when net_buf
debugging is activated.
Change-Id: I732f579fab2390cb16804cb35b83f46e65fca342
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
TCP maintains 'sent_list' for retransmission if it doesn't get ACK for it.
Same list is not freed on net_tcp_release() call. This causes memory leak.
Change-Id: I2b2def1ea19487cc48ea4fbb6343ef0c773f288f
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Due to commit fece856959 ("net: tcp: Clean up FIN handling") the
tcp_established() callback now handles TCP connections which are
in various ending/closing states other than TCP_ESTABLISHED.
Currently, these states are generating the following error and not
being processed:
Context 0x123456778 in wrong state 6.
(Shown when TCP is in LAST_ACK state).
This commit also fixes a memory leak issue discribed in
Jira: ZEP-1658
Analysis of the memory leak issue is here:
When TCP connection is established, tcp context is in
NET_TCP_ESTABLISHED state. Once it receives FIN message from client
it goes to NET_TCP_CLOSE_WAIT and then it turns to NET_TCP_LAST_ACK
after connection closing request from server. Now server gets final
ack from client, but tcp_established() will reject it because current
state is not in NET_TCP_ESTABLISHED. Even if server receives proper
ack, it is not handled by server. Hence 'sent_list' is not freed.
Change-Id: I41c8af2e6851809f87a02c271a4290cf3d823ebb
Signed-off-by: Michael Scott <michael.scott@linaro.org>
NET_ASSERT(net_nbuf_iface(buf)) should be called before setting
it on context [net_context_set_iface(context, net_nbuf_iface(buf))].
Change-Id: I9a1da1214857e96e03784bc98a9aae5cf59ef0fc
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Using char or uint8_t relevantly.
Jira: ZEP-1723
Change-Id: I512cb6ff4800cd23f6539e7a47c7f3c72dc94183
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The interface L2 address type is set at the same time as the
L2 address is set to the network interface. This is most
convinient place to set the address type.
Change-Id: I712d7357d075959eb79df3463141cfbc6d163a74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently, for the following MQTT msg fields:
- client_id
- will_topic
- user_name
- topic
their length is computed inside the routine that receives the MQTT msg.
Although this simplifies development, also imposes one restriction:
data must be null-terminated. Sometimes, data is received from other
sources and not generated by the application, so the null-terminated
constraint may be considered problematic for the user.
This patch removes the assumption that string fields are null-terminated.
Current data structures are already prepared to handle this case, so no
API change is required.
Change-Id: I5a147a5b21e0da49541cbe62baac363c8737cd3e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch updates the Remaining Length field from uint16_t to
uint32_t. The MQTT std specifies that this field must be
unsigned 4 bytes length.
Change-Id: I319d0745c673faece4bbd4db29b1bafad78ac199
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The dhcpv4 client code builds ip and udp packets from scratch rather
than using the network stack to do the heavy lifting (why ?).
When it computes the udp checksum of each packet it builds it neglects
to clear any preexisting detritus from the checksum field. The result
of this is that some packets will be built with correct checksums and
some will be built with incorrect checksums.
This is the underlying reason that the dhcp client often taken many
retransmissions and elapsed time before in order to acquire an IP
address.
Change-Id: Iebd1ed34e06f7f2e53d45f6d1555e22f48490287
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Fix long standing issue where a dhcpv4 message type is compared
against a dhcpv4 state machine state name rather than a message type.
The issue probably arizes due to the similarity in names between
messages and states. By accident, the relevant message types and
states happen to share the same numbers, hence the implementation
works, but is ill defined.
Change-Id: I5c028de4336ff42f6696e28b3492c932c58b5a05
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Makes it cleared that zoap_update_from_block() doesn't modify the
packet.
Change-Id: I35429b153370c50eb5ae9c914b47a3144faf2f04
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
This fixes the case that a request for block number (NUM) 0, using a
16 byte block was considered invalid.
This was because it is encoded as the value 0 (zero), which can be
expressed as the BLOCK1 option present but without any value
associated. The old code considered this the same as the option not
existing.
Change-Id: I0f3912803a88865e9f544a6d0078ed4231775a88
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
In order for OpenOCD to have a high-level view of an RTOS, it uses the
GDB protocol to obtain symbols from the system.
The GDB protocol, however, does not allow obtaining fields from
structures directly, and hardcoding offsets is not only brittle (due to
possibly different architectures or changes in the code), it's also
infeasible considering Zephyr is highly-configurable and parts of key
structs can be compiled in or out.
Export an array with offsets for these key structs. Also add a version
element in that array to allow changes in those structs.
Change-Id: I83bcfa0a7bd57d85582e5ec6efe70e1cceb1fc51
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
List container changes apparently were merged in the wrong order causing
leaving it with a compilation error.
Change-Id: Ib9d9502ddb39330c262e495a33592d0340713d83
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Change the handling of iface parameter in net_if_ipv6_maddr_lookup()
function:
* If the *iface is set to NULL, then return the found
interface to the caller.
* If the *iface is not NULL, then use that interface
when doing the lookup.
Change-Id: Ia1f0365170ea9f3e615d189231160614a80d241a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Because of the change in next commit "net: if: Change
the iface param in net_if_ipv6_maddr_lookup",
we must initialize the network interface to NULL.
Without this the multicast address lookup will fail.
Change-Id: I113b44ce23c5f2ecbbf1698972078f102995e891
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make the IP address parameter const because we are not
modifying the IP address in net_if_ipv6_maddr_add() or
net_if_ipv6_maddr_rm()
Change-Id: I98c19de132e58c386f661e8a76a349d562a82c71
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the function does not change the original data, make
the corresponding parameter const.
Change-Id: I1125a2f9205dc73de2f0aac0c30110591baace1e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the TX thread is not in k_poll() when conn->state gets set to
DISCONNECTED and a dummy buffer is pushed to conn->tx_queue the
bt_conn_prepare_events() function would have failed to add the
connection to the poll list for cleanup. To ensure the cleanup always
happens introduce a new flag that indicates that a cleanup must
happen. The extra benefit of the flag is that we no-longer need a
dummy buffer, but can simply use the conn_change signal to wake up the
TX thread.
Change-Id: I369584d305261ab3666b931c786daff9d131d228
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
From k_poll_signal_init() documentation:
The poll signal contains a 'signaled' field that, when set by
k_poll_signal(), stays set until the user sets it back to 0. It thus
has to be reset by the user before being passed again to k_poll() or
k_poll() will consider it being signaled, and will return immediately.
Change-Id: I55daac92dd6293ac653fd7fa0f907b0b7fd99d65
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
When iterating to the subscriptions to be removed the code has to keep
a reference to the previous node but it case the subscription matches but
doesn't need to be removed it doesn't update the prev node which may
corrupt the list in case the next node end up being removed.
Change-Id: Ic5448f01bf78d293f93b9a7078a0147385ea1d23
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Implement RFC2131 4.1.1 requirement that at dhcp implementation wait
for a random delay of 1 to 10s before sending the initial DISCOVER.
Implement RF2131 4.1 requirement that at dhcp implementation set the
initial retransmit timeout at 4 seconds and exponentially backoff on
each retransmit.
Change-Id: Id7029f3ed16a5f886dbd555fed87320aeffe31aa
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Rather than reuse XID's on retransmissions, always use a unique XID.
Either behaviour is permitted by rfc2131. Debugging the dhcp client
in the presence of multiple dhcp servers with significant packet loss
in the network is much easier if we don't unnecessarily reuse request
identifiers.
Change-Id: I5c82cbdbf3dfc0ef88cae036aa863946844c144f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
finalize_segment() will call net_ipv4_finalize() or
net_ipv6_finalize(). Both the functions perform net_nbuf_compact().
But after finalize_segment(), net_nbuf_compact() called again, which
is unnecessary.
Change-Id: I9fab63bcc44eec87061a4b55edd5053cf6556a75
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Protocol family is checked in prepare_segment() and in same function
it's again verified by finalize_segment(). So remove the double checking
in finalize_segment().
Change-Id: I17123ab8741d017d7e3ff1ef3fb07371b0d4aa66
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Using net_buf_ref() technically works but debugging the network buffer
allocations is more difficult if done like that.
Change-Id: Iac81bd3ab95547741d49f32763baaa54e97b4877
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If subcription was found within the subscription list,
we have check if remains identical subscription
from the next node.
Otherwise none unsubscription is realized.
Change-Id: I38132d7c80575801885b8057902f3d4666b08aea
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
If the buffer given to hci_cmd_done() is not from the command buffer
then using the cmd(buf) macro is not valid. Simply bail out from
hci_cmd_done() if this is an event that didn't have a matching command
buffer.
Change-Id: Id8357a23a307f4ef3a9214a4e1f7d853a18cb907
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If a net context is not connected or listening, we can go ahead and
call net_context_unref() to free it up instead of waiting for
FIN_ACK which will never happen.
Change-Id: Ice06f572df64f2edb5918c10c92087ce0b7b254a
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Several error messages are currently being logged as NET_DBG which
requires the user to have CONFIG_SYS_LOG_NET_LEVEL=4.
Let's show these as errors so they are more visible.
Change-Id: I28c9a1aedb78787ef098a9bf565472a437373933
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Current API description of net_nbuf_compact() is not very clear.
The first parameter needs to be the first net_buf in the chain.
The changes to this API are needed in order to clarify following
use cases:
1) User provides fragment that is not first of the chain and compact is
successfully done. In this case there is no free space in fragment list
after the input fragment. But there might be empty space in previous
fragments. So fragment chain is not completely compacted.
2) What if input fragment has been deleted and api returns the same
buf?
So this commit simplifies the API behavior. Now net_nbuf_compact()
expects the first parameter to be either TX or RX net_buf and then it
compacts it. It fails only if the input fragment is a data fragment.
Change-Id: I9e02dfcb6f3f2e2998826522a25ec207850a8056
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The net_nbuf_push() API is not used by anyone. Semantics are not
clear and following patch requires changes to push api, so removing
this API for now. If needed this can be re-introduced later.
Change-Id: I1d669c861590aa9bc80cc1ccb08144bd6020dac5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The ethernet header location was incorrectly calculated
and the result pointer had some random value.
Change-Id: I6b2deee787a78444f3ee3be805d4b82ebb6c3664
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently fragmentation introduces empty fragment in the
beginning of the list, and adds fragmentation header, and moves frags
data to previous fragments. This is done based on condition that max
data should be multiples of 8 bytes and offset is based on before
compression.
It will fail at scenario when current fragment has not enough space
to move from next fragment and next fragment has more than allowable
max bytes. This will cause memory overflow which is typically seen
as double-free error to the user.
This is solved more simple way by this commit. First detach frags list,
prepare new fragment and attach that to buffer. Then move data from
detached frag list and free the fragments in the old one.
Change-Id: I5e3693d47828ff3b92db4ba5f6c00c0b751daadc
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If we are in the end of the fragment chain, then we can just
bail out as there is nothing more to do. There will be a
double free if we continue as the last entry is already
removed at this point.
Change-Id: I0f9782b408244d283dc7e3e087359dd00bada7a9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Added a placeholder for CAN (Controller Area Network) support.
Change-Id: Ia6587df71a87f7439691768a04ba7ca07142e72f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Prior to commit df201a0e4b ("net: context: Assign a random port
number when context is created"), TCP clients were assigned a random
port number when the incoming sockaddr parameter's port value was 0.
After the above commit, this is now broken as it will bind to port 0.
If left this way, every TCP client would need to add a line of code
copying the context->local sockaddr_ptr's port value into the
src_sockaddr port prior to calling net_context_bin().
Instead, we can reinstate this behavior in net_context_bind(), by
making sure we only overwrite the randomly assigned port in the
context->local sockaddr if the incoming sockaddr parameter has a
port which is != 0.
Change-Id: I0f27f031f743d50c351ecf9ab55b5282a20ff292
Signed-off-by: Michael Scott <michael.scott@linaro.org>
If we receive a neighbor advertisement, we need to free its
net_buf because we are returning NET_OK to the caller. This
return code means that we consumed the net_buf but we did
not call net_nbuf_unref() in this case.
Change-Id: Ia6d8f1b440be87eff5d2b14a23336a37be6d6a04
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The pending buf needs to be freed after it has been sent
to the network. We took the ref when pending buf was saved,
now we need to unref it when it is about to be sent.
Change-Id: I1e429969895700000a8aa124bd645db2d52d036c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The controller code should not use BT_ASSERT directly.
Change-Id: If0b7d8e21d2ab4569a564bd03e36e4eb9204c595
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is not used outside of sdp.c and has no declaration.
Change-Id: I420a6b98d1b46fedffa29d042267b9c606d04c46
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
'buf' variable of type struct net_buf was one of the arguments for
finish callback in response to each AT command sent. 'buf' variable
not used in that function. So removed 'buf' variables from the argument
list.
Change-Id: I7d6aa6082f524012ae13a04426915076130ddf69
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Subscribe value is set to zero before calling notify callback,
to distinguish a subscription failure from an unsubscription
on disconnection (when flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE is set).
Change-Id: Ia91220492d82041b2c385bf88a15180387e7a483
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
If found error during service level connection disconnect rfcomm.
Change-Id: Ida425375975b8d60ab1024d07a8ffe7745ae0b54
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Some application protocol required non-persistente subscription
across connection even in bonded case.
Flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE specify if subscription
must be remove during disonnection.
Change-Id: I1bc2bbbb4bc86f58905e44a7eb267ca0871f2fdb
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
The subscriptions callback may free or reuse the subscription so all
instances that where this could happen need to safely fetch the next
element which is why this changes switch to use sys_list_t as it has
SYS_SLIST_FOR_EACH_NODE_SAFE.
Change-Id: I37d51f27116ea0c057b560924a9416676477597b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Once the service level connection is done call the connected
callback.
Change-Id: I7541e221d4c03c939682ec70f1d9c093f87ceb09
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
We can go further with taking advantage of k_poll and merge the
connection TX thread together with the HCI command thread, thereby
saving even more memory.
Change-Id: I1792056fd4621d62c7cd05929094033acca45c74
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that the k_poll API is available we can use it to have single
connection TX thread instead of multiple ones, which helps reduce the
per-connection memory overhead by a substantial amount.
Change-Id: Icb5d4da87cf0d660bba8da43186d1e76f41c825a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Removing the module specific buffer pool. If future, use common acl_tx_pool.
Change-Id: Ie1452f981ef43642715be395315845cc2d9bb285
Signed-off-by: Arun Jagadish <arun.jagadish@intel.com>
Detaching the timeout from the tx_thread lets us prepare for merging
all TX threads into a single one with the help of k_poll(). There's no
need to define a new delayed work object since the existing connection
parameter update object and connection timeout will never need to run
in parallel. Additionally, but some CONFIG_BLUETOOTH_CENTRAL guards to
void pulling in unnecessary code when Central role is not enabled.
Change-Id: Ia1f222aa052edcecd484a924f2d9a63a3b8fd11f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reduce the pressure on the common RX buffer pool by reusing HCI
command buffers also for the Command Status or Command Complete
response to them. This also implies removing the existing Kconfig
variable for the command buffer sizes since the size is also dependent
on maximum Command Complete event sizes. Instead, reuse the RX buffer
size also for HCI Command buffers.
Change-Id: I006b287d64a0c9ca40de741aa9a424a49a927385
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With an upcoming patch the HCI command buffers will be reused for the
Command Complete/Status HCI events. The controller HCI code needs some
refactoring to postpone the event buffer allocation so that the
parsing state of the HCI command buffer isn't touched.
Change-Id: I1f614fb9f02ed1886ca84198fbc8c64abc29e44f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A subsequent patch will start reusing HCI command buffers for
receiving the response, so the distinction of received vs sent data
headroom would just make the code unnecessarily complex. Instead, just
merge these two variable into a single one.
Change-Id: I31d846331939f1a2270df7ed0c75112825e16493
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The C pre-processor doesn't allow using sizeof() in comparisons such
as "#if FOO < sizeof(bar)". To make it possible to use such
comparisons where the sizes of headers are involved, introduce helper
macros for the headers instead of always having to hard-code magic
numbers into the code.
Change-Id: Iaf654cb4aaa49e83360901f5b01225ba4b952854
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the driver send() fails we need to free up bt_dev.sent_cmd.
Change-Id: I41b6293dfe09f1d94d7f85663ddbebed40cf6e90
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds API to allow user get SupportedFeatures attribute ID.
Jira: ZEP-1112
Change-Id: I91a1bf548d99c5c7cc75682aed19e89390350533
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Adds API to get available specific information included in protocols UUID
tree during parsing Protocol Descriptor List attribute. Usually it's to
be remote Server Channel/PSM number operating on applicable protocol.
There're a few helper functions added to be able parse and retrieve such
information from raw record data.
Jira: ZEP-1112
Change-Id: I736a780b95ba54821d36e6011b739f5ff37cd64f
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Both all-zeroes and all-ones addresses are invalid. Fix the check for
this so that we fall back to a static random identity address when
needed.
Change-Id: I17cf903e0f3ed321311d86d09bed19343c2c801a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This will reduce memory consumption by 23 bytes per session.
Change-Id: I1831b59881eaefb68f93c30e298b8f97d63c7428
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Session idle timer should not be started in dlc destroy if
session is already disconnected (which can happen in scenarios
like acl disconnection where in dlc is detached from session and
destroy will be called from tx thread) otherwise timer function will
get invoked for a disconnected session.
This patch moves starting of idle timer from dlc destroy to
the point dlc disconnect is recieved from remote since idle
timer is to handle only that scenario.
Change-Id: I94501515a182ff0e2348ba4e2df63100f2f52209
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
The nRF5x come preprogrammed from manufacturing with either a public or
random static BLE address in the FICR register. Use the random static
one when present instead of generating one during Bluetooth
initialization.
Change-id: Ic733cb926e0414e56d6f8be65b033692e914b72a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Doing it only in net_context, prevented to do it once NS succesfully
finished. This generated an error in 15.4, where pending data had wrong
ll reserve size.
Change-Id: I0f917fb76171457e5dff2c29e44edb8f00662150
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We must use the nexthop instead of destination address
when sending the packet. The current code mixed destination
and nexthop addresses and ignored the nexthop when sending
neighbor solicitation message.
Change-Id: I53887c16ef6fcf8365f1f47ab5792cb208dd273e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Keep track of amount of bytes that are sent or received from
all network interfaces.
Change-Id: I706481aab1a7e0cf2bc78d032f2ef4ebbabe3184
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current behaviour has an issue when UDP context is created with local
port number 0, net_conn_input() happens to treat zero port as
a wildcard ("receive packets for all ports"). net_context_bind()
for a UDP context doesn't affect its existing connection in any way.
Proposed solution is, context should be created with a random free
port assigned and bind() updates connection information from context.
Jira: ZEP-1644
Change-Id: Idb3592b58c831d986763312077b0dcdd95850bc9
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The port numbers in the range from 0 to 1023 are the well-known ports
or system ports. Do not allocate them for users.
Change-Id: I4d7b4e1314759e4d8b260669946b9880282642c0
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Commit-ID 83ed3a29be changed the way
fragments are managed after being sent, and this brought a bug in the
active scan logic. Up to active scan to keep the buffer referenced
relevantly now, which is simpler than it used to be.
Reported-by: Johann Fischer <j.fischer@phytec.de>
Change-Id: I23db4bab878328b1ca3cb313e737de819177c281
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds a NET_L2_BLUETOOTH_ZEP1656 which sets NET_IF_POINTOPOINT to
avoid using nbr cache with Linux peers as they send wrong link
addresses.
Jira: ZEP-1656
Change-Id: I842f4cbb99ae9d9c004494739c07189c191929fe
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This flag can be used by driver to indicate pointopoint links which should
not require destination link address to be resolved.
Jira: ZEP-1656
Change-Id: I58dd3bf48485d6203e75373497e00668317b9825
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The net_nbuf_get*() functions were calling net_buf_alloc()
with K_FOREVER. This can cause issue if called from isr
context. The fix is to check if we are in isr and then try
to alloc net_buf with K_NO_WAIT.
Change-Id: I809170f2cd059480d436763e19a35386d9bdf048
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The returning 'len' was always informing the remaining available space
in that net_buf fragment. This not the expected behaviour for
incoming packets, in this case, we really want the size for the
payload already present in the packet.
When this function is called with a packet without a payload, with
will return the available space in the packet, when the payload is
already set, it will return the size of that payload.
Change-Id: Ia4643b8c2a015ad2316bed037e457b186e420b19
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Channel, PAN-ID, short and extended address
Change-Id: Icdf94dff6f59cd155a072a609290197b37bd084c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Channel, pan-id, short and extended addresses.
Change-Id: Ib63dadac37d649df3efc8fdd67f5312d3a7c8e20
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix setting short address through net mgmt API. It's not about
coordinator's short address, but local one.
Change-Id: I320143e40d336a1085bf12b17a88a2c35da83504
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ORFD or RFD does not matter: the extended address should be set
according to device's MAC address.
Change-Id: I39d09c3a953283eeaa30b908ea159638604bd72b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Delete redundant line and let the common exit point to release
the buffers.
Change-Id: I97e0ef79803083fabd841fb3d38d67c04ff31f7b
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Don't try to process null or zero-length buffers generated by
the IP stack. Zero-length buffers are valid at the TCP layer but
contain no information for applications.
Change-Id: If66d301527f56ca8e8761789b7fd6931fc37b8e0
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add the malformed callback that will be executed when a message
is received and it does not follow the MQTT v3.1.1 spec.
There is another case when this callback may be executed: when
the IP stack reception buffer's size is not enough to hold an
MQTT message.
The publisher and subscriber parser routines are updated to make
use of this callback. Inline documentation is also updated.
Change-Id: Id1d34336c4322673ca85f2db0b8d432db3c9afa8
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
1) Remove some variables pointing to user-provided data.
2) Pass the context structure instead of those variables.
3) Homogenize the use of "ctx" for all the callbacks receiving the
struct mqtt_ctx * pointer.
Now users must use the CONTAINER_OF macro to access data required
by the MQTT callbacks.
Change-Id: I871c0bd8601a67b39187683215579f9ed0087cf9
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Although the buffer size validation works as it is inside the
mqtt_linearize_buffer routine, let's move it before getting a
data buffer from the buffer poll.
Change-Id: Id80af8a1e188929769463b04deaef3956b63cd00
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This makes sure ll addresses are properly set before sending reducing the
duplicated code on L2 drivers.
Change-Id: I5330c1d00a344e77555c6f31033ae42af20214bf
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Fix comparisons in net_if_get_by_index and net_if_get_by_iface:
__net_if_end is not a pointer to a net_if structure.
Change-Id: Ie8e3a457c3f0fa97c080b38b5b7d2b420c50252b
Signed-off-by: Julien Chevrier <julien.chevrier@intel.com>
There is dead code that is never executed so removing it.
Coverity-CID: 157585
Change-Id: I6926289b5735b78fcb99ad493d1b05198b9e36cc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previous commit: 6e6281af96
"net: tcp: Only return -ETIMEDOUT if timeout>0 in connect"
missed that K_FOREVER needs a semaphore taken, but has a
value of -1.
Change the logic here to timeout!=0 to handle this case.
Change-Id: Iae6a784443810130a7de267226483426fbd4f0d4
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The RFC requires we honor the 2MSL TIME_WAIT timeout, support for
which was just removed with the FIN cleanup. Add it back, but make it
optional (proper sequence number and ephemeral port randomization
makes true collisions a birthday problem in a ~80 bit space!).
Change-Id: I176c6250f43bba0c914da1ee7f0136dcb1008046
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The context may live for a while after the user closes it (c.f. TCP),
and of course the documentation specifies that the user must not use
it after calling net_context_put(). Don't confuse them by invoking
their callbacks on the "closed" connection; it's likely that the user
has destroyed her own tracking data and the user_data pointers would
be garbage.
Change-Id: Iba9cc7025c6ea4a94cc4796903966f8d1b831996
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The connection close paths were a little tangle. The use of separate
callbacks for "active" and "passive" close obscured the fundamentally
symmetric operation of those modes and made it hard to check sequence
numbers for validation (they didn't). Similarly the use of the
official TCP states missed some details we need, like the distinction
between having "queued" a FIN packet for transmission and the state
reached when it's actually transmitted.
Remove the state-specific callbacks (which actually had very little to
do) and just rely on the existing packet queuing and generic sequence
number handling in tcp_established(). A few new state bits in the
net_tcp struct help us track current state in a way that doesn't fall
over the asymmetry of the TCP state diagram. We can also junk the
FIN-specific timer and just use the same retransmit timer we do for
data packets (though long term we should investigate choosing
different timeouts by state).
Change-Id: I09951b848c63fefefce33962ee6cff6a09b4ca50
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
A FIN packet generated by a net_context_put() must go into the normal
transmit queue and not be sent synchronously. Previously sent data is
expected to be delivered and acknowledged before the connection is
terminated.
An advantage we get with this change is unified timeout and retry
handling for FIN packets.
Note that there remains a misfeature here where the queing of the FIN
results in a synchronous switching of the connection callback to
tcp_active_close(), which will prevent any further data received from
being provided to the user.
Change-Id: I2d41316549da9fee383b4f32af5e8b3adf4cb122
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The death of a network context was sort of a mess. There was one
function, net_context_put(), which was used both by the user as a way
to "close" the connection and by the internals to delete it and to
"clean up" a TCP connection at the end of its life.
This has led to repeated gotchas where contexts die before you are
ready for them (one example: when a user callback decides the
transation is complete and calls net_context_put() underneath the
receive callback for the EOF, which then returns and tries to inspect
the now-freed memory inside the TCP internals). I've now stepped into
this mess four times now, and it's time to fix the architecture:
Swap the solitary put() call for a more conventional reference
counting implementation. The put() call now is a pure user API (and
maybe should be renamed "close" or "shutdown"). For compatibility,
it still calls unref() where appropriate (i.e. when the context can be
synchronously deleted) and the FIN processing will still do an unref()
when the FIN packets have been both transmitted and acked. The
context will start with a refcount of 1, and all TCP callbacks made on
it will increment the refcount around the callback to prevent
premature deletion.
Note that this gives the user a "destroy" mechanism for an in-progress
connection that doesn't require a network round trip. That might be
useful in some circumstances.
Change-Id: I44cb355e42941605913b2f84eb14d4eb3c134570
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The old default 2 is too low especially if TCP is enabled.
So in order not to confuse the application developer,
increase the default number of network contexts to 6.
Change-Id: I263bb4b6f31354a11d921d94aa97214abd85ae24
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
net_addr_ntop() will convert IPv4|6 address to string form.
Renamed existing net_sprint_ip_addr_buf() to net_addr_ntop()
and adjusted parameters as per API.
Jira: ZEP-1638
Change-Id: Ia497be6bf876ca63b120529acbadcfd9162a96e3
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This make sure the link-local address of the destination is added to the
nbr cache as that is accessed when calling net_ipv6_prepare_for_send,
this is needed when following RFC 7668 since link-local addresses are
never registered using nbr discovery.
Change-Id: I2bc578d33d1061726d0cbf46e4464df74d79e992
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
in net_print_statistics for RPL we had:
GET_STAT(rpl.dio..sent)
This wouldn't work or compile, so drop a dot.
Change-Id: Idd6b4dfd5fcae3b90bc977fe3ed301cd813ca87c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Currently, the function accepts a struct sockaddr * but the code
immediately type casts this to either in_addr or in6_addr. This is
incorrect behavior as the first field in a sockaddr is sa_family_t
and not address data.
So without special knowledge, a developer will use a sockaddr structure
as the parameter and then wonder why the address information isn't being
set correctly.
Let's change this parameter to void * which makes this function similar
to inet_pton().
Jira: ZEP-1616
Change-Id: I1fc9368da999d90feb07c03fac55dcc749d4eba6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
If the user supplied connect callback uses too much time, then
it is possible that the connect_wait semaphore will timeout
even if the TCP connection was established correctly. This issue
can be avoided if connect_cb is called after we have released
the connect_wait semaphore.
Change-Id: I175e80f2ad48de657d0d99a44340c5ee1a17364c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The fat library uses its own typedef for integer parms and expects a
UINT to be either 16 or 32-bits in length. We potentially get into
trouble when we build with newlib if we use an uint32_t. Lets just use
unsigned int which should cover all cases for us.
Change-Id: I3dbbf4871ab65dd12488d41cb06a06387c128339
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The hci_raw version of bt_buf_get_rx was expecting an int for timeout.
Let us int32_t instead so we match both the hci_core version and the
type that net_buf_alloc expects.
This addresses a possible build issue if/when int32_t differs from our
default (ie, newlib).
Change-Id: I69374c48da8f2b96fa2bd418ff505fbaacda11f0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change BREDR_NAME to DEVICE_NAME so it can also be used as the LE
device name.
Change-Id: I9ef55d9dff098372d47d9d5754ad7a7163a65bc0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added structure definition for stream end points
and the a2dp stream.
Change-Id: I6d0cc08611f5179397bea6200eb9244d7c1cc8d6
Signed-off-by: Piyush Itankar <piyush.t.itankar@intel.com>
Fixed channels don't really use channels state as they don't need
connection setup.
Change-Id: Ie8b1327db0269a45e9ccb6049f8dda87aa445fb5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Adds state callback handler to allocate memory to AVDTP on an incoming
connection. Also, abstracts searching of free session as a function call.
Change-Id: Idee6b7a0507b0b75c0007717e351ca12de0cb5be
Signed-off-by: Piyush Itankar <piyush.t.itankar@intel.com>
This is mainly for backward compatibility with 1.0b devices and for
spec compliance. CFC is mandatory post 1.0b spec where in MSC FC
shall not be used.
FC bit in MSC is used to manage the flow control. If FC is 1 then
the device is unable to accept frames.
Implementation is done by reusing "tx_credit" as a binary semaphore
wherein it will be blocked if MSC is recieved with FC bit 1 and
unblocked if FC bit is 0. Once tx thread is scheduled then semaphore
should be always available until all the buf in queue is sent.
Change-Id: I91181668ec0f46ff0b02905dd97e4503fc1fa7a7
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
v24_signal in MSC response should be the copy of it received
in the command.
Change-Id: I9723ba182bf5911025c7a57220cd70687ca785f3
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
This implemnts the feature to handle the unsolicited response
received from the AG. In the hfp_hf.c file the unsolicited_cb function
process it.
Change-Id: I3ca6c8d4a1522d02f7160e2fe4ae1598cd93ce7e
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Make NET_MAX_6LO_CONTEXTS depends on NET_6LO_CONTEXT, otherwise at the
moment even deselecting 6lowpan leaves NET_MAX_6LO_CONTEXTS set.
Change-Id: Iaa34d324005817be05190e203f6899ab89f89e5d
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Making NET_IPV6_DAD depends on NET_IPV6_ND instead of default fixes
issue when deselecting NET_IPV6_ND, NET_IPV6_DAD is still selected in
this case.
Change-Id: I633b1a71fb5fdcd7ecc75be80a737d8bda142b2e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
NET_IPV6_ND is always selected by NET_ROUTE which is always selected
for NET_IPV6.
Change-Id: I316838033cccd205b24add6626521bbab5a68715
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This permits to catch issues without the need to enable debug level.
Change-Id: Ic3c66a84be587e955d532cc321161a3ae7b5d69d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The option is no longer used so it can be removed.
Use CONFIG_NET_IPV6_ND option instead.
Change-Id: Ibaa3d3deb52b8b176e85f8b9e1d8c80c1026aea1
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Let's use the generic console input type now. This will be useful for
other console input drivers such as telnet.
Change-Id: I787a1e9d86481d5f8c4803453726d9042a89dea4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ll addresses need to be set properly before sending as the stack is not
checking if they are NULL.
Change-Id: Ia4e96240f18b53b0e32e21649a8b571c94260731
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If src and dst link layer addresses are not then 6lo fails
to compress the packet.
Change-Id: Ie2692def49f8a101194e3669dbaec00b557e14ce
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
No need to set the status to -ETIMEDOUT in connect callback
if user did not want to have a timeout when doing a TCP connect.
Change-Id: I6d6e565a8d12bcefbcd9de751e789b5e43aad244
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A connection refused needs to be exposed to the user, otherwise the
connection will be stuck as a zombie forever.
This patch also adds a ENOTCONN check in net_context_recv() to match
the one that was already there in net_context_send().
Change-Id: I4f9ae46dd849f68ed97976add7da5daf1932cf55
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The net_context_connect() callback was being invoked synchronously
with the transmission of the SYN packet. That's not very useful, as
it doesn't tell the user anything they can't already figure out from
the return code. Move it to the receipt of the SYNACK instead, so the
app can know that it's time to start transmitting. This matches the
Unix semantics more closely, where connect(2) is a blocking call that
wakes up only when the connection is live.
Change-Id: I11e3cca8572d51bee215274e82667e0917587a0f
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
With CONFIG_NET_DEBUG_L2_BLUETOOTH is disabled the code generate the
following warning:
subsys/net/ip/l2/bluetooth.c: In function 'eir_found':
subsys/net/ip/l2/bluetooth.c:301:16: warning: unused variable 'addr' [-Wunused-variable]
bt_addr_le_t *addr = user_data;
^
Change-Id: I1a1ca20c4f2e4fa8aa2a551d2fffa1f86874760e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When checking if the L2CAP channel is connected it is not enough to check
if the conn member is set since the connection may still be pending.
Change-Id: I93a2328943b0ca0e42cdb5c525b30c7cdddd1c18
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use printk(), snprintk() instead of printf() and snprintf().
CONFIG_STDOUT_CONSOLE is anyway disabled by default so printf()
will not output anything without it.
Change-Id: I9ad778e318fe999e79ec34182f2de8574e45b7d4
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Older default value of 2 is too small for even simple uses, for
example enabling just CONFIG_NETWORKING, CONFIG_NET_IPV4,
CONFIG_NET_SLIP_TAP makes a Zephyr application hang on start up
(apparently, waiting to allocate more buffers). While value of 3
is enough to cover the above options, set new default to 4 to
accommodate configurations with IPv4/IPv6/UDP/TCP enabled.
While the new default slightly increases RAM footprint, it's
apparently better for users who are short of it to optimize it
explicitly, rather than potentially make every Zephyr beginner
wonder why enabling networking breaks applications in non-obvious
way.
Change-Id: I76e83517f0d914ce616a930c3c48ee5c52567b88
Jira: ZEP-1619
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The K_<thread option> flags/options avaialble to users were hidden in
the kernel private header files: move them to include/kernel.h to
publicize them.
Also, to avoid any future confusion, rename the k_thread.execution_flags
field to user_options.
Change-Id: I65a6fd5e9e78d4ccf783f3304b607a1e6956aeac
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Convert driver to use the CMSIS NVIC APIs rather than the internal
ones so we can remove them in the future.
Change-Id: Ib9fe696e8d5e55f60865d3fd958a035135ce517a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
TCP states are swaped between "server" context and the new connection
context. But in any case the "server" context should loose the
information that makes it able to accept other new connections.
The swap was badly made, as the "server" context was loosing the
accept_cb (!) and the user data pointer. Instead the new connection
context was unrelevantly inheriting those.
Change-Id: Icc877449e1d4c4e59553dcbfd41718c5006edca0
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It is useful that the user API can know whether the connection
was established properly or not. So this commit adds status
parameter to connect callback in net_context API.
The call to connect callback needs to be set properly in TCP
code. This commit does not fix the connect callback call which
is not properly done right now in net_context.c.
Change-Id: I284a60ddd658ceef9e65022e96591f467a936a09
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Wrong pool pointer was used when printing pool information during
the unref in nbuf.c. During nbuf init, wrong pool pointer was used
when printing memory pool sizes.
Change-Id: I9ed08cf7afa3c841c97ea981b97fff37aa40a984
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the parameter "timeout" is set in net_context_connect(), the
assumption by the user is that the function would wait for SYNACK
to be received before returning to the caller.
Currently this is not the case. The timeout parameter is handed
off to net_l2_offload_ip_connect() if CONFIG_NET_L2_OFFLOAD_IP is
defined but never handled in a normal call.
To implement the timeout, let's use a semaphore to wait for
tcp_synack_received() to get a SYNACK before returning from
net_context_connect().
Change-Id: I7565550ed5545e6410b2d99c429367c1fb539970
Signed-off-by: Michael Scott <michael.scott@linaro.org>
net_context is used for more than just TCP contexts. However,
the accept_cb field is only used for TCP. Let's move it from
the generic net_context structure to the TCP specific net_tcp
structure.
Change-Id: If923c7aba1355cf5f91c07a7e7e469d385c7c365
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When SYNACK is received we dont hand off the netbuf to anything
which will call net_nbuf_unref, so let's not mark it NET_OK.
Instead let the code path fall through to mark it NET_DROP.
Change-Id: I1f883e1a13c53c930bf50c07ff701e3db6f02d8a
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that the TCP_FIN block is after a potential packet_received()
tcp->send_ack should be appropriately set to the last sequence
processed.
In the case of a TCP_FIN buffer, we should advance it by 1 or else
the destination will continue to retry to send the last block.
Change-Id: I9c97d35a87ad6cc1a50f928b237780bff4cd2877
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Since we default to a return value of NET_DROP, we
can remove the automatic NET_DROP in the TCP_FIN block.
The return value will be set to NET_OK by packet_received()
if appropriate data is found which needs to be sent to
the callback.
Change-Id: Ib2634ba34440ca7053a4e98bf80f12cf6fbbd361
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Buffers marked TCP_FIN may still have data attached to them
which needs to be processed and handed back to the callback.
Let's move the TCP_FIN handling to after the data processing
section now that we have a copy of the TCP flags to do this.
Change-Id: I90f53b10e393024ebffebe1837b8866764b8a7ac
Signed-off-by: Michael Scott <michael.scott@linaro.org>
buffer TCP flags can be cleared during packet_received so let's
save a copy of them for later.
Change-Id: I401e99c1ed2723dac4e86da58635b548a5645c13
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Allow building the IP stack with newlib by enabling linux extensions.
Jira: ZEP-1592
Change-Id: I6714b73c7666a6f56c5203e2754ce1d7d94af0f1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
CONFIG_STDOUT_CONSOLE is anyway disabled by default so printf() will not
output anything without it.
Change-Id: I8013e4efa5cb760215316e9413734281fb576f4d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In some situations, for example, when the remote side sends a RESET
message indicating that it is no longer interested in observing a
resource, it is helpful to have a way to obtain the obverser
representation.
Change-Id: Ifbf627f9170be844fd525c557dda8cb722ac7aff
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When retrieving options that represent an integer, the order of the
bytes being considered was inverted, resulting in invalid values being
returned.
Change-Id: I8ba84f77e3402066632c0ba650939266c87a8ea2
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
For example, when a RESET packet is passed to zoap_handle_request(),
there's nothing it can do, and it's not an error, so it returns
success silently.
Change-Id: I025bb44733521d6132999c219aaa292a3de302d7
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
When parser encouter DHCPV4_OPTIONS_END, it immediately returns NET_OK.
No need to maintain end variable here.
Coverity-CID: 157584
Change-Id: I4c8b91f37ae882845c280dab1a8204966aaac00a
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Pointer udp will be NULL when (!(CIPHC[0] & NET_6LO_IPHC_NH_1))
condition is true.
Coverity-CID: 157588
Change-Id: I8aa1eb2e4d4aee8039631d76ad0ecc345247d6b5
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
When contex information provided and DAC bit is not set and vice versa
are invalid cases.
Coverity-CID: 157569
Change-Id: I1b798703cbbb6155a7bdf734d0fcde9ce48c409c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
In net_nbuf_get(), check that context pointer value is not
null before accessing data via it.
Coverity-CID: 157600
Change-Id: I7e7ea19a85f6fbef129e9ce699ea740d3be84cb8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If neighbor is not found, then ignore the timeout.
Coverity-CID: 157583
Change-Id: Ia2199970bd862e43901f5717025271c11c74af5e
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to allocate separate fragment to store the IP
protocol headers.
Coverity-CID: 157582
Change-Id: Ib0dd5d28cd6876a0cf2de3b063c030ef64da998c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Callback cannot be null so no need to check its value.
Coverity-CID: 157572
Change-Id: I26e4b24c41d30aa9007b78895975035e6bf8807f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The context parameter might be NULL so we need to check
its value before accessing its content.
Coverity-CID: 157571
Change-Id: I7f75323d9d261a77421688f37a40bb44ff3ca2bd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The link layer dereferences a buffer right after it is transmitted.
If this extra reference is not held, the second time a buffer is
retransmitted, the reference that TCP holds when keeping the buffer in
the `sent_list` will be taken, and retransmission won't happen reliably
anymore.
As soon as the TCP fragment is acknowledged by the peer, the
`sent_list` reference is taken, and the buffer is freed.
Change-Id: Ie50f9acf02c1dff74248a5dfbec3785a91ff90f7
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
No more than 4 bits are necessary to store the state of a TCP connection,
so better pack it using bitfields so that it uses only 4 bits instead of
32, by sharing space with `retry_timeout_shift` and `flags` fields.
There are 12 (or 14, if you count the 2 unused bits in the `flags`
field) bits remaining in the same dword, but I don't know what to to
stuff there yet.
This also changes all direct field access for the `state` field to
function calls. These functions are provided as `static inline`
functions and they perform only casts, so there's no function call
overhead.
Change-Id: I0197462caa0b71b287c0773ec5cd2dd4101a4766
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This frees up some more memory as well, by computing the maximum segment
size whenever needed. A flag is set in the TCP context to signal if
the value has been already computed.
Change-Id: Idb228d4682540f92b269e3878fcee45cbc28038a
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This value is never set (always zero), so it's safe to remove it from
the net_tcp struct.
Change-Id: Ie4c1d90204a9834f2223b09828af42ee101bd045
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Rename the variable to `retry_timeout_shift`, and shift-right the value
each time there's a timeout. This saves some memory in that structure
by using the holes left due to alignment.
Change-Id: I18f45d00ecc434a588758a8d331921db902f4419
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Cancel all delayed work timers: FIN, ACK, and retry timers. Also, do
that unconditionally regardless of which state the machine is in, as
that's a no-op if the timer has not been started yet.
Change-Id: Ia36b97c6823943976447fbd6389ae04862c19ff9
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The net_tcp struct was being cleaned up and destroyed when the
outbound FIN packet is sent on a connection that already received an
inbound FIN. That's not right, per spec we need to wait for the ACK
(though this would be benign cheating). And worse: there were code
paths which were themselves spec-compliant where the net_tcp struct
(now a NULL pointer) would be used after this spot leading to
occasional crazy behavior on socket close.
Don't do it this way. Clean up the TCP struct at the same time we
destroy the net_context. Much saner that way.
Change-Id: I4bc6b97eb0b71a7fa8faea02c1eb4c4d3bd3ae6d
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The TCP stack inherited msot of the user_data management from UDP, but
it doesn't quite work. It's not possible to have a single pointer in
the general case, as e.g. a net_context_send() call may happen
synchronously underneath a recv callback and clobber the pointer, even
though there will be much more data coming later on the active stream.
Put a recv_user_data field into the TCP struct and use that. Long
term, it would be good to revisit this and come up with a unified
solution that works for both. There is yet another "user_data"
pointer in net_connection that seem likely to overlap too.
Change-Id: Id3a8eca64fc680e0e80b74944c4d621d7810a8fe
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Let's drop the lladdr variable and get the link address and
length from the net_linkaddr_storage variable instead.
Change-Id: I75a5d08527cda7df102db897ade9015d39f10caf
Signed-off-by: Michael Scott <michael.scott@linaro.org>
lladdr.addr doesn't point to any storage value when it's
handed off to the net_nbuf_read function. This results
in a write to an undefined area of memory.
Fix this by pointing lladdr.addr to a net_linkaddr_storage
structure's byte storage array which can handle the maximum
specified length.
Change-Id: I05e0a0420b262ba1e5ac95cebe1f0d91f54878ce
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The net_linkaddr_storage structure contains an array of bytes used
to store the link address. This array can be different sizes
depending on the CONFIG options used when building. To facilitate
consistency and error checking let's introduce a new helper function
to copy the addr and len values to this structure.
Also move all uses of memcpy related to net_link_storage structures to
the new helper function.
Change-Id: Ic547d86b07e62e5ac3bc330d4eaeb4508a143200
Signed-off-by: Michael Scott <michael.scott@linaro.org>
- Introduce NET_LINK_ADDR_MAX_LENGTH which is either 6 or 8
depending on whether CONFIG_NET_L2_IEEE802154 is used
- Instead of being a placeholder single index array of uint8_t,
let's use NET_LINK_ADDR_MAX_LENGTH to assign the size of the
"addr" array field in the net_linkaddr_storage structure.
- Now that the "addr" field of net_linkaddr_storage contains the
true size of the link address, we can remove "storage" field
which was hard coded to 8 bytes (2 uint32_t's).
- Fix 2 references to the "storage" field of the net_linkaddr_storage
structure.
Change-Id: I2ea12058280b289f65085964eb7d503d4fd260c2
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For combined builds with Controller+Host the Controller's HW RNG is
used instead of TinyCrypts PRNG.
Change-Id: I4dbe85e547c057cf57ae0934b10866f2bb9f610d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case the channel provides its own MTU and allocator it should be
able to store as much data as set in the MTU, based on that the code
can give enough credits to fill the entire channel MTU.
Change-Id: I291cf1bb643f200bde191914e814f681f4f65c3e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Added pointer to store the callback function
from the application in the Request structure.
Added userdata param, to be used to fill AVDTP resp.
Change-Id: I8f3289545fdbbd91e4ed7f9983f4f4331d9b59a6
Signed-off-by: Arun Jagadish <arun.jagadish@intel.com>
This makes l2cap_chan_add updates the state to CONNECT so it doesn't
have to be done manually for both incoming and outgoing code paths.
Change-Id: I7331e49c675c83c6c1b184eeecc49c75c446a1ff
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Try to use IS_ENABLED instead of #ifdefs whenever possible.
Change-Id: I330769204914286bb98583dd89a3d849d4fcc128
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Try to use IS_ENABLED instead of #ifdefs whenever possible.
Change-Id: I77d2e53f7aa7f2832513f235a63ad2cf14e73cb1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Try to use IS_ENABLED instead of #ifdefs whenever possible.
Change-Id: I78a3ccc6fcb84b431198f1a6c46aa6d50e9e9cd1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Try to use IS_ENABLED instead of #ifdefs whenever possible.
Change-Id: I4da93076a27a33b15a9b9119cfe5a1ff68acba0b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new IS_ENABLED macro allows exposing conditionally enabled code
always to the compiler, even though it may not ultimately end up being
built. This is in particular useful for letting the compiler catch any
logging format string errors. Introduce a new BT_DBG_ENABLED macro
that c-files need to define before including <bluetooth/log.h> in
order to choose whether BT_DBG() logs are enabled or not.
When no Bluetooth logs are enabled the patch also modifies the log
macros to have the format strings checked with the help of the
__printf_like annotation and empty static inline functions.
Change-Id: Ie6bc8e10727b5b306f3ed0f94089a07a22583d9b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introduce a new callback to bt_conn_cb that allows the application to
decide whether the accept or reject an incoming connection parameter
request. If the request is accepted the callback allows the
application to also adjust the values to what it thinks are more
appropriate.
The Zephyr Bluetooth API allows multiple registered connection
callbacks, so in principle there may be multiple le_param_req()
callbacks. It's recommended for an app to just use one (for clarity),
but if there are multiple the app is responsible for managing
potentially different requirements. In the case of multiple callbacks
each callback will receive the modified parameters in case a previous
callback modified them.
Jira: ZEP-1474
Change-Id: I098db5791aac521f1edfa9fefdf847db0a27e3a5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BT_L2CAP_RX_MTU is counted starting with the BLUETOOTH_RX_BUF_LEN
variable, which doesn't include the BLUETOOTH_HCI_RECV_RESERVE
contribution (this would only be valid if we started subtracting from
BT_BUF_RX_SIZE).
Change-Id: I1ab3eaf8907946c56c2a9fe16b2074f3a3027a0f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
BT_BUF_RX_SIZE is used for the RX buffer pool which is used for both
ACL data and HCI events. It should therefore not contain any
ACL-specific details. This patch removes the ACL header size from the
macro and instead makes taking it into account the responsibility to
the Kconfig option. Since buffer sizes are anyway rounded up to the
nearest multiple of 4 the default goes up from 70 to 76.
Change-Id: I41274d9131e7529d41c16bd66de95637fb150a29
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CONFIG_BLUETOOTH_RX_BUF_LEN shall not be used as RX MTU since it doesn't
account for ACL and L2CAP headers.
Change-Id: Ic3ebb4bd13d86a39174840f0ab625b66e863018a
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is mainly for backward compatibility with 1.0b devices and for
ICS & spec compliance. CFC is mandatory post 1.0b spec where in
Aggregate FC shall not be used.
Aggregate FC is managed using FCOFF and FCON messages. This is for
the entire session which means that all the dlcs in that session
will be affected.
Implementation is done using binary semaphore wherein it will be
blocked when FCOFF is recieved and unblocked in FCON.
Once tx thread is scheduled then semaphore should be always available
until all the buf in queue is sent.
Change-Id: Ibfd2c4d033cef64c238ead83474f9e171572de1e
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Bluetooth Core Specification v5.0, Vol 2, Part E, 7.8.12:
"The Supervision_Timeout parameter defines the link supervision timeout
for the connection. The Supervision_Timeout in milliseconds shall be larger
than (1 + Conn_Latency) * Conn_Interval_Max * 2, where Conn_Interval_Max is
given in milliseconds."
Let's remember that:
conn_interval is given in units N * 1.25 ms
sup_timeout is given in units N * 10 ms
sup_timeout_ms > (1 + latency) * (conn_interval_ms * 2)
yields:
sup_timeout_n * 10 > (1 + latency) * (conn_interval_n * 1.25 * 2)
yields:
sup_timeout_n * 10 > (1 + latency) * (conn_interval_n * 2.5)
yields:
sup_timeout_n * 4 > (1 + latency) * (conn_interval_n)
Change-id: I30ac1d375a1baaa3e61f4c29b1165110599e1f7c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reduces stack pressure a little bit, and also paves the way for
introducing an application callback for accepting an incoming
connection parameter update request.
Change-Id: Ib02c14e27cbe34f85d663f36abd0597683ae1dc1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When receiving notifications we should be properly matching against
the remote address of subscribed peers.
Change-Id: Ibcba1101aac418fd02f9068667f84e8294aade07
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are no users of this API and no (currently) envisioned use cases
for it. Remove it for now - it can always be brought back later if
there's a need for it.
Change-Id: I6530e096e3671c844a3f7dea8856147ffc716d71
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Rename the elements of 'enum at_cmd_type' in order to follow the
name spacing. Which should have prefix of 'AT_' for each elements.
This patch also involves the renaming, corresponding handler
function of 'enum at_cmd_type' with prefix 'at_' i.e 'cmd_start' as
'at_cmd_start'.
Change-Id: I722a25954163c06e131b94042c6a18e1e3458f6e
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Rename hci_le_rand to bt_rand and make its parameter types compatible.
This also includes updating rand_get() to use size_t instead of
uint32_t & uint8_t.
Change-Id: I4d434dfbbaf339b1bc7b451d358d07a291dd0375
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller bt_rand() ties into the hardware which uses less memory
and is more power-efficient than using the TinyCrypt PRNG.
Change-Id: I7570d18f3e84dae3d5c2d3322b5d37cd3e8f3b6b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Having TX buffers split into numerous pools has the downside of
increased memory consumption. This patch takes the initial step to
consolidate these pools into a single one, saving about 248 bytes of
RAM for a basic configuration.
Change-Id: I449ba18b44a9a6af68e9a2c44f19a9286eb88b14
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Uses sys_slist_get function to get node and automatically, if valid,
remove one from the list.
Change-Id: I4cee6fbb064bf9644efdb7e6771e702b1f08678a
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Fixes not supported now format specifier.
Change-Id: Ia01ea3fd18acfeed6f4a3899334911dac1b76643
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Be nice and inform user about unsupported and dropped frames.
Change-Id: Iaf0e7ed660a926c45dac9fc36b788c4c786eac11
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This adds NET_REQUEST_BT_DISCONNECT which can be used to disconnect
IPSP in case it is connected.
Change-Id: I8da00b02ee08611bef5f4c0708936b2d31fd2a93
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds NET_REQUEST_BT_SCAN which can be used to scan peripherals
advertising IPSS UUID.
Change-Id: I2463079d182b4da080e6ef94d883c7c1e24a454c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a shell module called "net_bt" that exposes Bluetooth L2
management commands.
Change-Id: Ia6da1d38cfd51502119758a8f6abbb6d1cd31743
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Connect command can be used to initiate a connection, which in IPSP
terminology refer to a router role.
Change-Id: I12b9428924c88a9c68d3adbfe9016a0dd690aade
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Including logging/sys_log.h before net_core.h prevents SYS_LOG_LEVEL,
etc, to be set properly.
Change-Id: Iaa7aa98110aa455162836be1d9560fbfc03569df
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This decodes the event layer, code and type when debugging is enabled.
Change-Id: I23c6fb200f3287a138e46df9f472c9982898675d
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
net_context_put() forgot to release the conn_handler field causing
subsequent failures in net_conn_register() when they ran out.
Change-Id: I0d306b5035199422fa8788338ac9da8d1900d5f9
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
TCP didn't actually have a way to signal synchronous receipt of a FIN
packet. Extend the recv_cb API to allow a NULL buf argument with
status==0 (by analogy to Unix's zero-length read) to signal EOF.
Update docs too, and also echo_server which wasn't prepared to handle
this situation.
Change-Id: I7dc08f9e262a81dcad9c670c6471898889f0b05d
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
In icmpv4, after calling setup_ipv4_header() function,
only calculate ICMP chksum, not calculate ipv4 header chksum,
ipv4 header chksum still 0, the other side will drop this pack.
Change-Id: I1550a4c8c7ab63132d70ba6ce19a7caf78ad84e6
Signed-off-by: li zj <279939902@qq.com>
When router receive dhcpv4 request with ciaddr not 0.0.0.0,
some router reply NAK, dhcpv4 never successful.
Change-Id: I4b66b18f7d30ad5a1b638fdca0bb204ed078d551
Signed-off-by: li zj <279939902@qq.com>
The tcp_synack_received() function ends with a call to send_ack().
However, if we don't update the sequence and ACK values, we'll send back
headers with 0 values and the destination will try resending over and
over.
Fix this by saving the seq and ack values when a TCP_SYN is flagged
in the header (which should be the case almost any time this function
is used as a callback).
Change-Id: I57f07ce719f2b6e2fb34c96c867d2e1c37f342ba
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Once SYNACK has been received for a TCP connection, we need to set the
net context state to NET_CONTEXT_CONNECTED or else calls to sendto()
will fail with -ENOTCONN.
Change-Id: Idd78e1dcdd5ac0bca5d3fba40b59ab8fde6b8729
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When calling net_context_connect, the local address family
is never set prior to calling net_tcp_register. This generates
an error:
"Local address family not set." (-EINVAL)
Let's set the local address family prior to this call.
Change-Id: Ic5f2edf684d14f9bb77019c49c95e5524a406417
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When TCP SYNACK is received we register the connection via the
net_tcp_register function. During this call several errors are
generated concerning local and remote address information not
being set.
Let's copy the local and remote address data prior to this call.
Change-Id: I17cd83f7b4b7e65e45fec1810fb38f745653bdc7
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In other portions of the code we use the sys_put_be* function
to shift the values from the current system endian to big
endian array of bytes. Let's be consistent and do that in
the prepare_segment function as well.
Change-Id: I5a1a4c30ddf313c9e978be98fd969899f5de6190
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The NET_SLIP Kconfig choice option doesn't really do anything for us,
plus we get warnings related to setting CONFIG_NET_SLIP=y in prj.conf
files.
Warnings like:
warning: override: reassigning to symbol NET_SLIP
warning: override: NET_SLIP_TAP changes choice state
So remove NET_SLIP choice and remove CONFIG_NET_SLIP=y in the prj.conf
files.
Change-Id: Ibccf9cf167f4c8a4df480ca0396bf83fcf60df1e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
select is more intuitive and easy to remember, and it is shorter too :)
Change-Id: Icc79e5cb88163344c1e2fcf65e313c33c4afa2cc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Disk IO functions are used by both FS and USB Mass Storage.
This patch refactors those from FS directory to a separate one.
In addition existing, config options were modified to make
stuff meaningful.
Jira: ZEP-1276
Change-Id: Ia2a2e18f3dbbbdb964c3dc0427d8138ad86134cd
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In commit bf4fb51f44, "net: if: Add NET_IF_UP flag"
a reference to ctxt->iface was added in the ipsp_disconnected function.
Let's add the ctxt variable definition to fix the build break.
Change-Id: Ib06047e333504f3db4fe175fb3ef1dce347e1916
Signed-off-by: Michael Scott <michael.scott@linaro.org>
If the length of all fragments is used instead, the TCP header is also
considered; sequence numbers do not consider the header.
Change-Id: I19e77ac0fe62ca619b0903dd0265f8ea4878cdf7
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The net_buf_frags_len() function returns a size_t, which is an unsigned
integer. Store on an appropriate size_t variable instead.
Change-Id: I98aa4c0ddd7c464737436aa9ce13bdc86c11da2b
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
TCP packets need the computed packet length early so they can fill in
a correct sequence number in their generated ACKs. Waiting for
packet_received() is too late. Precompute it before needed, and skip
the evaluation later.
Change-Id: I25547009f88277e0042c74f2005a141819797886
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
On accepting a new connection, the stack does an odd "swap" trick
where it updates the struct net_tcp record on the *listening* context
with the values from the new connection, and then swaps it with the
empty one that got allocated for the *new* context.
Unfortunately this swap forgot to swap the net_tcp "context" field
backpointers, so the net_context retrieved at runtime was for the
wrong connection. Surprisingly, this actually almost worked for a
long time, except that the destination address would be wrong in the
newer setup.
Change-Id: I0c1812ddb9f9ff3e7deb60d1fd67cafd9ba96997
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The source address for a TCP SYNACK must (obviously) be the same as
the destination address of the SYN that produced it. But the existing
IP packet creation routines would simply fill in a default address
from the net_context struct, which is correct for *established*
connections, but for the listening socket is generally INADDR_ANY
(i.e. all zeroes) and will result in an arbitrary choice for source
address (e.g. a link-local address on the same interface) which can
easily be wrong.
So we need to pass the correct address all the way down from the SYN
packet handler code through the net_ipv*_create() packet creation
functions. This requires lots of API plumbing, but relatively little
logic change.
Change-Id: Ic368f8cef6689f8a27cbafd5933a4964d5cc457e
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This one exposes IEEE 802.15.4 net mgmt requests through the shell. User
has then the ability to directly make relevant requests like raising a
scan, associating, etc...
For now, it assumes the 15.4 interface is the only one on the system and
thus will rely on net_if_get_default().
Change-Id: I8eb20565b8231e6cfcba6c1479179cc85ff1d8e5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It is then possible to set the channel, pan_id and short address through
this API. Such features are mainly useful for testing purposes.
Change-Id: I41aeb397afdb231458a3b13638f3e13d3ac28a6c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When a CNAME is part of the DNS answer RR, sometimes a label with
a pointer is found. The CNAME must be reused to create a new DNS
query and that CNAME will become the new DNS Query QNAME. This new
QNAME must not include pointers.
This patch introduces the qname_copy routine that "linearizes" a
given QNAME (perhaps with pointers).
The dns_read routine is also updated to reflect these changes.
Change-Id: I8e8f64e85e2cbf494fd589e2b7a67d470d34604b
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the mqtt_subscriber_parser routine and modifies the
mqtt_init routine to allow an MQTT subscriber app to receive MQTT msgs.
Change-Id: Ie54ab892dacbc4386acab78a8991eba1850d8171
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Changes applied by this patch:
- Add the mqtt_publisher_parser routine
- Add the MQTT_PACKET_TYPE macro to get the MQTT msg packet type
(required by mqtt_publisher_parser)
- Add the mqtt_linearize_buffer (required by mqtt_publisher_parser)
- Add the mqtt_recv callback for reception
- Modify the mqtt_init routine to install the reception callback
The mqtt_publisher_parser routine is a callback used internally
to execute the appropriate mqtt_rx routine. Only the following
messages are handled by this routine:
MQTT_CONNACK, MQTT_PUBACK, MQTT_PUBREC, MQTT_PUBCOMP and MQTT_PINGRESP.
On error, it executes the ctx->malformed cb, if defined.
This commit also introduces the mqtt_linearize_buffer routine that
will be used to linearize an IP stack fragmented buffer. This patch
makes use of the net_nbuf_linear_copy routine to linearize the
incoming buffer. mqtt_rx_xxxx routines are also updated to handle
linear buffers (no fragmentation).
Currently, all the network protocol routines assume that the input
buffer is not fragmented. Future versions will remove that assumption
and the mqtt_linearize_buffer routine will be removed as well.
Public MQTT API is not affected by this patch.
Change-Id: I02fece67052ffbc7cb393d5ca545c503da463c4b
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Avoid undesired behaviors by exiting once an error is detected.
Change-Id: Id8e6accd6cd096274fe1c40a615d290967f1d4b9
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit improves the buffer error handling in the mqtt_tx
routines.
Change-Id: Ic8e5761d927fe881b2376b6ac948a412e3b1168a
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The mqtt_rx_publish is used to process incoming MQTT PUBLISH
messages. This routine performes the following steps:
- take ownership of the rx buffer containing the MQTT PUBLISH msg,
- call the MQTT parser routine, and
- determine, based on the incoming message's MQTT QoS,
the next action.
Change-Id: I3cc011cf0c280205161d0484f12a2cfa79fdf44a
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Use the appropriate data type for some variables:
- const input arguments
- int32_t instead of uint32_t for timeout
- uint8_t instead of int for variables that take just a few
possitive values.
Change-Id: Id7d762b400fa17e6751829ac401cd7c13aabb7b2
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit changes some function signatures found at the private
MQTT Packet Lib. Input arguments representing arrays can be considered
'const', avoiding compiler warnings when passing "const arrays" in
MQTT applications.
Change-Id: I3ebaa9c7ff5fba74324bf79c55027cdd82669eaa
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This commit adds one routine previously found at the DNS resolver
library. The net_nbuf_linear_copy routine allows to "linearize"
an IP stack network buffer. This routine is required by functions
that must jump between big chunks of data that in this case may
lie between many fragments. Tracking fragments may be a tedious
task, so getting a linear copy of the buffer will reduce code
complexity altough it increases memory consumption.
The DNS client library is updated to reflect these changes.
Change-Id: Iae321f99fa9b05fae7e722b6d41baac427d82d7e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
PAN coordinator can decide to eject a client device from the PAN by
disassocating it.
Change-Id: Ia868554d40a7aceb4c75a0b426db45f56003fbb7
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If associated, this will request to disassociate from the PAN. That's
only client side, PAN coordinator can also disassociate a client, which
case is not handled here.
Change-Id: If308f51b62c5006b4a2db53d0c891e8192f3c198
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Active scan differs from passive scan by sending a Beacon request (thus
the "active" part) and wait for beacons in reply to it.
Taking the opportunity to add debugging output to scanning logic.
Change-Id: I85001b1ea17f4ec4cd315dc39524c4d8f053cee2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now we can handle incoming MAC command frames.
Association result ONLY for now.
Change-Id: Ib54b1757185ed079fe6914fa7939347020e006d9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Such management request will enable association the 15.4 device to an
existing PAN.
Change-Id: I61ffd5e4d8192716e067c5225b3327f08944063b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is used only for scanning at this point. But will be needed to get
slots information and else in the future.
Change-Id: Ib917469134c6ba5a54485847c612d3755f62ed35
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Currently, as only CC2520 device is supported: it will loop over the 16
channels present in 2.4Ghz spectrum. However, this will need refinement
as soon as other spectrums will be in use: L2 layer could request
capabilites from the device in order to know which range to use.
Scan result is done one at a time for now. It's unlikely going to fit
all production use case, so it's going to change in the future.
Change-Id: I2fafec49eb5cbfca1a4f04107ba3b6511d7d956d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It can be thus used to track the status of network interfaces in order
to act accordingly (no need to try sending things on network if the
interface is down for instance).
Change-Id: Ie160ef0dfdad6679d531d05a7abada96ad1de7db
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds enable callback which can be used to notify the L2 driver about
changes of interface state, the L2 driver can then check if the new state
is allowed and reject otherwise.
Change-Id: I4bb6b1e32be2633f24694c0246585f803f8c645d
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds NET_IF_UP flag support indicating the interface is up,
currently this shall only be used internally by the driver, later on it
shall be possible to make it public by using dedicated functions.
Change-Id: I38090da4030395b2341733b846004789416d61c1
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It's possible for the Public Key to be available by the time that the
bt_hci_cmd_send_sync() returns, so we need to make sure the flags have
the right values no matter what.
Change-Id: I053093b6611af360f52b14ddca50d409388f9475
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As per the spec, the station which disconnects the last dlc
should disconnect session also. In case if remote does not
do it we need to disconnect otherwise rfcomm will be connected
without any dlc. So this starts an idle timer to handle the
above scenario.
This also starts a disconnect timer to handle in case remote
does not respond to session disconnect request.
Change-Id: I3b45aa5bf4c35fd81dc10974f2b0b6d4cfe4ea7d
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Rename cind_status_handle_values to ag_inidcator_handle_values.
Because the same function will be reused internally for +CIEV
Callbacks.
Change-Id: I875064de17700d72ea89dbbe0f5cb6554c813a5e
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Reset AT and COMMAND state to process unsolicited response received
after processing result recieved for AT command sent to AG.
Change-Id: Id2a5827ce5b098336291696157027699479478cf
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Confirmation callbacks needed not be registered with AVDTP
during A2DP initialization
Change-Id: I2cdf8c5a283775e49fa6e7e9404024e26d05a767
Signed-off-by: Piyush Itankar <piyush.t.itankar@intel.com>
This basically implements timer for connection and disconnection.
Conn timer will be started when dlc is initialized and stopped
when it is connected. Authentication if any, will be also included
in this timer.
Disc timer will be started during disconnect initiation.
Change-Id: Ia4b74e478fefa42db21aef528e623a24c72ddf7f
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Moves rfcomm_send_disc() and rfcomm_session_disconnect() to call it
while doing timer implementation.
Change-Id: I5805d31fb45181193385f055716c8518d68cc4a1
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Adds more descriptive comment to the code responsible for handling no
resolved UUID case.
Jira: ZEP-1112
Change-Id: I1af07949e19246d51bab9df05504a90f5fb22bb2
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
User may want to know when getting called user UUID callback handler
on what UUID the result data was retrieved from server.
Jira: ZEP-1112
Change-Id: Iabb2dbdf0f3cfdb24244e052f094c7549164b199
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
In order that host can continue a connection event by
enqueuing packets, the number of completed packets event
needs to be generated as soon it arrives on air. Hence, the
Controller now calls the radio_event_callback on every radio
Rx complete ISR.
The callback executes at the Radio ISR priority, take care
to only do as little as necessary in the callback, say, just
a semaphore give to wake up the hci_driver's thread.
Change-id: If48afd0f1390d450bc1e7ec66f1c9fd45208d9a4
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
For the host to be able to block on the recv_thread while waiting for a
number of completed packets HCI event, those are pulled from the radio
in a new, higher priority thread that also schedules the execution of
the lower priority event/ACL data recv_thread.
Change-id: I9d356bd297d0504cb16a032fb5fe5530693546e2
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
net_buf shall not be used with k_fifo since net_buf_unref will assume
unused bytes in the beginning are actually fragments causing it to
unref them as well.
Jira: ZEP-1489
Change-Id: I5ce420de73b245dc20eb15ea4d8d0b6ba346e513
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since callers of bt_recv() have so far anyway been required to know in
which context to call it (based on e.g. bt_hci_evt_is_prio) it's
cleaner to have two separate APIs: bt_recv and bt_recv_prio.
Change-Id: Icd0d9aed9c51ffd2def31432c4ffcc16a9f13ccd
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The recent redesign of the H:4 HCI driver means that the smallest
safest RX buffer count goes down to 2. Default is left at 3 however to
get a bit better performance.
Change-Id: I879c7bd3a769f973dfb9bd179d196ab91f9d2abe
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Advertising reports are the only HCI events which we can drop if we
are low on buffers. Allocate them therefore with K_NO_WAIT rather than
K_FOREVER.
Change-Id: I0b7c92647f9be54b8746da837037725f8161a452
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the controller already uses a thread for receiving data it makes
sense to enable the BLUETOOTH_RECV_IS_RX_THREAD option.
Change-Id: I927b20c1a0afaea8d000df28cc220a69ae817d59
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller uses K_FOREVER for the allocations so there's no
benefit in trying to use specialized pools (which exist to try to
guarantee availability of buffers for critical data).
Change-Id: I130f2c44a2f28af1284290e6a0b17dcba438862f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Allocate the event buffers after the ECDH operations rather than
before them. This way we don't hold on to the buffer for potentially
multiple seconds while the buffer could be used for other things.
Change-Id: I0fcc34ec4bea2265b7df3c1de3587c2a850c974e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There's no need to use the type-specific helpers since those anyway
map to the same pool.
Change-Id: I74750f545c989bb921abca58166fe591ed325856
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Give more sensible values when RECV_IS_RX_THREAD is configured.
Change-Id: I40b5bd88213d224cc29f63fccef6cecee5868f77
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The separate ACL & event pools will soon be removed, and it's already
now convenient to have a generic API when the exact type of the
incoming packet is not yet known.
Change-Id: I84cb65d17ea69ebeaeb21532fbf76689e4fb59a0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller doesn't support this feature and the only driver that
was needing it (h4.c) will be converted not to rely on it in the next
patch.
Change-Id: Ia514b79b6d05aa128768c2355353b7797e8b8977
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add support for using the context bt_recv() is called in as the RX
thread, rather than having a separate host-side RX thread.
Change-Id: I256bfe5dece5272c816f2292e58747553189963d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Refactor the bt_recv() logic to make it easier to insert #ifdefs to
remove the RX queue and thread when the context calling bt_recv()
itself is sufficient enough.
Change-Id: Ie8c5a4dfe9533a4464a2e4909c94d3e1b185b55b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the controller doesn't need ACL host flow control it may want to
optimize and use a single pool for incoming data.
Change-Id: Iec2a69bd2d7a127c7329d0423ab5ce6b73cb9904
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This option has not been used so far and will only contribute
unnecessary complexity in subsequent patches that introduce a concept
of combined RX buffers.
Change-Id: I53e0ce5155eebc352b84ba41b30ecb9d9958699f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After getting whole UUID response for SSA PDU request the user can be
informed about discovery results. Result data feeding the user is
splitted to logical record chunks if more than one record was found.
Every such portion represent unparsed SDP record prestripped from record
length. Each response record data passed to user starts from first raw
attributes data and the record response buffer's length tells exactly
about each record length. User UUID callback handler's return result
can drive delivery (dis)continuation of every such portion to the user.
Jira: ZEP-1112
Change-Id: Icec518ca7bab3c8dfef4a966d98e9d9004894bcc
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
This analyzes the dlc stack using stack_analyze() which is coming
as 188 with BLUETOOTH_DEBUG_LOG off.
dlc stack (real size 320): unused 68 usage 188 / 256 (73 %)
So increase the stack size to 256.
Change-Id: Ie5d5f267f4f618747551f0bfd0e05ffb47e0bb91
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
When getting very first SSA PDU response for given UUID we can extract
from it the counter telling us how much data will be delivered by server
to collect all complete response for given UUID. Let's use that
information to check if the room allocated by app is big enough for
collecting resolved data.
Jira: ZEP-1112
Change-Id: I91515da668d89e05755d64e427dee0936bf20323
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
skip_whitespace() API name is changed to skip_space(). Where the
skip_space function is to skip only SPACE(ASCII Dec: 32).
Change-Id: Ib28ffa45295912505bc27a986803ed0ae2b0002c
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Rename the API's with 'list' which uses the term 'stream'.
For example 'at_open_stream' is renamed to 'at_open_list' and
the same applies for other API's which uses 'stream' in it.
Change-Id: I62bed70de3d85cd4890b10e04eba27ae2de1907c
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
The private_key parameter to generate_keys is supposed to be 32 bytes
in size, i.e. an array of 8 uint32_t variables.
Change-Id: Ia891fd68bfd8662983b898084e5a8524b7a9b8e2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds driven by user params buffer location to be populated by UUID
resolved data. Corresponding handlers responsible for connected and
disconnected states of L2CAP transport channel used by SDP PSM traffic
automatically allocates and unrefs such memory. Data receiving handler
performs buffer fill up.
Jira: ZEP-1112
Change-Id: I8aa97e6e69344dca0f241a4e9097acac75e14a7c
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Adds two extra checks against invalid length of attribute payload
frame.
Jira: ZEP-1112
Change-Id: I089442a5b9631471f9f394860681f1483e021c43
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Iterates all UUID params list delivered by user. When iteration finish
release SDP client L2CAP transport channel.
Jira: ZEP-1112
Change-Id: I0602e32a5296a05719ad1385b4aff537350b3e7d
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
This commit introduces a very light-weight and lock-less
scheduling of the Controller's deferred function calls
called the Mayfly.
Earlier work implementation used in the Controller had an
O(n) to schedule a function in a linked list that used IRQ
lock during modification of the linked list in the
Controller's ISR executions.
Mayfly is a compile time configurable matrix of queues
where an execution context-safe queue exists between two
execution context, one being the caller and the second
being the callee. Callee(s) are run in a software interrupt
but can also be run in an OS thread.
There are minor clean ups too in this commit related to
folder structure.
Change-id: I5ff44dcee6679d2f5ce9e8437d98d6c868782f3d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Enable connection encryption setup in 3 connection
intervals. Peripheral will respond to Encryption Request
with Encryption Response in the same connection interval,
and also, will respond with Start Encryption Response PDU in
the 3rd connection interval, hence completing encryption
setup in 3 connection intervals. Encrypted data would be
transmitted as fast as in 3rd connection interval from the
connection establishment. Maximum CPU time in Radio ISR will
increase if this feature is selected.
Change-id: I16f2863fc2aaed624826505739519d4de1ac44c5
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration to select Tx buffer size, this
value will be returned in the HCI LE Read Buffer Size
command response.
This configuration will allow lower Tx RAM usage when
larger PDU sizes are desired in Rx direction only.
Change-Id: I5106a448d78a0754c4b0f6fa61fd5dcacd87a67c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration and conditional compilation of
RSSI measurement during a connection.
Change-id: I5a2f23f76a7cbbd9569d53d31899a472bf39d3ee
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration to conditionally enable Data
Length Update procedure support in the Controller.
This will save CPU time, flash and RAM, if this feature is
not desired.
Change-id: I4515c0c7cf9aeb333a289397ae3c9bac04a08e4e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add additional conditional compilation of code not needed
when LE Ping is disabled in Kconfig.
Change-id: Idab40b1371488e06a6f2009fb553f7655b7b86f3
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Adds initial handling of SDP Service Search Attribute response PDU.
Currently attributes data are not collected. Main focus was done on
proper handling PDU continuation state to be able receive whole
requested SDP record(s) if found for given UUID.
< ACL Data TX: Handle 74 flags 0x00 dlen 24
Channel: 64 len 20 [PSM 1 mode 0] {chan 3}
SDP: Service Search Attribute Request (0x06) tid 1 len 15
Search pattern: [len 5]
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
OBEX Object Push (0x1105)
Max record count: 65535
Attribute list: [len 7]
Sequence (6) with 5 bytes [8 extra bits] len 7
Unsigned Integer (1) with 4 bytes [0 extra bits] len 5
0x0000ffff
Continuation state: 0
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 74
Count: 1
> ACL Data RX: Handle 74 flags 0x02 dlen 68
Channel: 64 len 64 [PSM 1 mode 0] {chan 3}
SDP: Service Search Attribute Response (0x07) tid 1 len 59
Attribute bytes: 48
Continuation state: 8
cd 91 5a 58 30 00 00 00 ..ZX0...
< HCI Command: Host Number of Completed Packets (0x03|0x0035) plen 5
Num handles: 1
Handle: 74
Count: 1
< ACL Data TX: Handle 74 flags 0x00 dlen 32
Channel: 64 len 28 [PSM 1 mode 0] {chan 3}
SDP: Service Search Attribute Request (0x06) tid 2 len 23
Search pattern: [len 5]
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
OBEX Object Push (0x1105)
Max record count: 65535
Attribute list: [len 7]
Sequence (6) with 5 bytes [8 extra bits] len 7
Unsigned Integer (1) with 4 bytes [0 extra bits] len 5
0x0000ffff
Continuation state: 8
cd 91 5a 58 30 00 00 00 ..ZX0...
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 74
Count: 1
> ACL Data RX: Handle 74 flags 0x02 dlen 68
Channel: 64 len 64 [PSM 1 mode 0] {chan 3}
SDP: Service Search Attribute Response (0x07) tid 2 len 59
Attribute bytes: 48
Continuation state: 8
cd 91 5a 58 60 00 00 00 ..ZX`...
< HCI Command: Host Number of Completed Packets (0x03|0x0035) plen 5
Num handles: 1
Handle: 74
Count: 1
< ACL Data TX: Handle 74 flags 0x00 dlen 32
Channel: 64 len 28 [PSM 1 mode 0] {chan 3}
SDP: Service Search Attribute Request (0x06) tid 3 len 23
Search pattern: [len 5]
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
OBEX Object Push (0x1105)
Max record count: 65535
Attribute list: [len 7]
Sequence (6) with 5 bytes [8 extra bits] len 7
Unsigned Integer (1) with 4 bytes [0 extra bits] len 5
0x0000ffff
Continuation state: 8
cd 91 5a 58 60 00 00 00 ..ZX`...
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 74
Count: 1
> ACL Data RX: Handle 74 flags 0x02 dlen 19
Channel: 64 len 15 [PSM 1 mode 0] {chan 3}
SDP: Service Search Attribute Response (0x07) tid 3 len 10
Attribute bytes: 7
Continuation state: 0
Combined attribute bytes: 103
Attribute list: [len 99] {position 0}
Attribute: Service Record Handle (0x0000) [len 2]
0x00010001
Attribute: Service Class ID List (0x0001) [len 2]
UUID (3) with 2 bytes [0 extra bits] len 3
OBEX Object Push (0x1105)
Attribute: Protocol Descriptor List (0x0004) [len 2]
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
L2CAP (0x0100)
Sequence (6) with 5 bytes [8 extra bits] len 7
UUID (3) with 2 bytes [0 extra bits] len 3
RFCOMM (0x0003)
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x09
Sequence (6) with 3 bytes [8 extra bits] len 5
UUID (3) with 2 bytes [0 extra bits] len 3
OBEX (0x0008)
Attribute: Browse Group List (0x0005) [len 2]
UUID (3) with 2 bytes [0 extra bits] len 3
Public Browse Root (0x1002)
Attribute: Bluetooth Profile Descriptor List (0x0009) [len 2]
Sequence (6) with 6 bytes [8 extra bits] len 8
UUID (3) with 2 bytes [0 extra bits] len 3
OBEX Object Push (0x1105)
Unsigned Integer (1) with 2 bytes [0 extra bits] len 3
0x0100
Attribute: Unknown (0x0100) [len 2]
OBEX Object Push [len 16]
Attribute: Unknown (0x0303) [len 2]
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x01
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x02
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x03
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x04
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x05
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0x06
Unsigned Integer (1) with 1 byte [0 extra bits] len 2
0xff
Jira: ZEP-1112
Change-Id: Ie282782fba6ef06c6826b3e624f83c8f4c94ebbe
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
The following readings were obtained after running the peripheral and
central_hr apps in qemu combined with the controller (hci_uart) on nRF51
and nRF52:
Main Stack 380
Idle Stack: 68
ISR stack: 532
Controller RX Stack: 388
HCI TX Stack: 516
The numbers set in this change provide a safety margin from the ones
measured empirically.
Change-id: Ice7ad7f081502e0ea1accf856a7937c0bf0783b2
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
reserve parameter of bt_l2cap_create_pdu() is incorrectly passed
as timeout.
Change-Id: Ieed293f52c2e98f16f1e43c498140178703236db
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
For consistency with RX_STACK_SIZE and the rest of stack sizes, rename
to use the normal naming scheme.
Change-id: Ib8d484482466fa8d629e6329e07b927abdd6f598
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add Kconfig configuration to conditionally enable LE Ping
feature in the Controller.
This will save CPU time, flash and RAM, if this feature is
not desired.
Change-id: I5fbbdbe8f45ac01c9b0d7b11e002a0d1db4d272e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The data pointer and length was not updated before invoking the
write_rsp function therefore providing pointer to the handle.
Change-Id: I5c27ab7a793979dffb8f1f2c68def027c45f2376
Signed-off-by: Louis Caron <louis.caron@intel.com>
This should also have been net_buf_add_mem(). Otherwise the buffer
gets corrupted.
Change-Id: I4687584777f446d398182c3e8c2cde5946987da4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move code that can be executed after radio tx/rx packet ptr
has been assigned in the radio h/w.
Change-id: I9c5a34ee6bb74c1265d7871bcdf93894e3e7b190
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added code to profile radio ISR execution time and generate
an event, which can be used to populate a vendor HCI event.
This event and associated code is disabled, subsequent
patch will add kconfig to enable it.
Change-id: Ic3fa3e0f4e36829a22a25ffee039949eaae561a7
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Use BT_WARN instead of BT_ASSERT to display unknown rsp in
HCI layer.
Change-id: I63c792468d9c4768f69df73395ee026a03521704
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Peer controllers not supporting LE Ping feature will
respond with unknown response PDU, handle it internally in
the controller rather than exposing it to HCI layer.
Discovered that controller was passing the unknown rsp PDU
to HCI layer when LE Ping was send to Nexus 5.
Unknown response for slave feature request was forwarded to
HCI layer, during that implementation unknown rsp for LE
ping too was getting forwarded to HCI layer.
Change-id: I4396c482e5546d78239cf41d88728de996e48d7d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This call was supposed to be net_buf_add_mem().
Change-Id: I5e4a718474905c433533fd1c1d7e8e0b7ff35739
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This helps simplify code that was previously combining net_buf_add()
with memcpy().
Change-Id: If44cf9cd651aba5e544e36567869f147468663eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
And it's not really a debugging option either, one might want to use it
for the features it brings. Thus moving it out of Kconfig.debug.
Change-Id: Ie1e2d2bcba94ad4b8354d3cc56087227184039b6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's make net stack having its own level of debugging through sys_log.
It replaces NET_DEBUG by NET_LOG_ENABLED, which is then semantically
better: someone wanting to log the errors might want that not only for
debugging.
Along with it, CONFIG_NET_LOG_GLOBAL option is added, in order to enable
all available logging in network stack. It is disabled by default but
might be found useful when warning/errors need to be logged, so it is
then unnecessary to selectively enable by hand all CONFIG_NET_DEBUG_*
options.
It is possible, locally, to override CONFIG_SYS_LOG_NET_LEVEL by setting
the level one want to NET_SYS_LOG_LEVEL. This can be useful on samples
or tests.
Change-Id: I56a8f052340bc3a932229963cc69b39912093b88
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's possible to know from which pool the nbuf comes from so
let's reduce nbuf size by removing its internal type attribute which
becomes then useless.
When a data buffer is not coming from nbuf data buffer pool, let's call
it "EXTERNAL", just to make debugging handling a little simple in the
code.
Change-Id: I6931394c8c4f594137f6380be0a0ba5cea371040
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use the interface function rather than writing directly to the iface
structure. Check for errors in nbuf read.
Change-Id: I75311755c2060b640325962ada28adea597cb914
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Detect non local IPv4 destination addresses earlier and route them via
the gw address. Ensure that the ARP table is populated with the GW
address rather than the final destination address.
Jira: ZEP-1473
Change-Id: I3b628584148b760340ef0fea4da4e8893702c832
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
s/energy_est/estimation when using net_rpl_node_energy_object.
Change-Id: I4b326a0dbbca11d48de0c595dfe843495fe10e04
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's much different than IPv4 where it's possible to find the whole
packet length. Here it has to count also the ipv6 header size by itself.
Jira: ZEP-1422
Change-Id: I84b1602ac75ef81b9ceda7898ca9dedf2e54d633
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
User application can request the information it wants via the generic
net_mgmt() call, following the NET_REQUEST_STATS_* codes.
Change-Id: Ia9e7d318cf11b7bf8bfaf1ad63c8c985be846cc1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will help to track only what's wanted (ipv6, tpc, udp, else...) if
needed to.
Change-Id: I5c2e5e582db629b5d0e1cd98004f693c50f532a4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's change from macros to inlined function to make things nicer.
Change-Id: Ie98e0667613961b03c84ca60bc551d0f473765f6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This file will own more statistics handling in a near future.
Change-Id: Ifaf86852f5c7166e6878b5dc8f4cd4c166dbee90
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It clutters a bit the code with ifdefs but it's quite useful when
debugging.
Change-Id: I4f6899d052921b8ef8a7ec2f6e7df927a1bca2f1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It will be thus possible to enable only the error logging, or the other
sys_log levels.
Change-Id: I0c0ed789f7cfbb4811320e8f8249151288274873
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
printk is anyway the routine being selected for sys_log.
Change-Id: Id6b516aa6ab8d4d420b9afe22b5e6b832dd3e216
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This moves the shell component into its own subsys and groups all
related files and options into a single place.
Additionally, one Kconfig option will now be required to enable the
shell:
CONFIG_CONSOLE_SHELL=y
The header files was also moved to include/shell/shell.h and can be now
referenced with
#include <shell/shell.h>
instead of
#include <misc/shell.h>
Updated documentation as well.
Change-Id: Iffbba4acfa05408055e9fd28dffa213451351f94
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A very common pattern in code goes something like the following:
memcpy(net_buf_add(buf, len), data, len);
To avoid having to create this kind of complex constructions every
time, this patch adds a new API which simplifies the call:
net_buf_add_mem(buf, data, len);
Change-Id: Ic1aeae4baf88b2295d139f672d5d265db2ddbe7b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Stops handle data if server responds with SDP Error PDU
Jira: ZEP-1112
Change-Id: Iaddb740f71fa86384753ab32956fc69b89faeea0
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Adds handler responsible for receiving SDP data on SDP client request.
For now simple validation are done on SDP response header data.
Jira: ZEP-1112
Change-Id: Ic6009030db34e26dfdbd57fa1b0a22f6e27b6a11
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
cid is uint16_t and L2CAP_BR_CID_DYN_END is 0xffff so doing
"cid < L2CAP_BR_CID_DYN_END" comparisong is always true resulting
in for loop not being terminated as expected. Check against cid
overflow instead. Code comment is also added for clarity.
Change-Id: I15d6d838ed8b731824e602d089d765614c96c6c1
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Resets SDP client session data on related L2CAP transport channel
disconnection state. Leave the channel itself reset to L2CAP layer.
Jira: ZEP-1112
Change-Id: I4d8a8f10908f5e599ba6506470b98508869cb21b
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Makes possible to append user UUID to context to be able later iterate
it on subsequent resolving process.
Jira: ZEP-1112
Change-Id: I193ff1cee199045c9686dc4ca200adf19db377e4
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Renames and refactors helper get_client_session to sdp_client_get_session
to follow existing naming convention and adds second helper creating
new SDP client session. Then simplifies using them the API implementation.
Jira: ZEP-1112
Change-Id: I6b919f521e6665a7117fa06208b3fa2ae5f77fda
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Peer sends Remote Port Negotiation command to set port
communication settings. Currently we accept all the settings
sent by remote.
If there is only one value byte in the request then current
port settings has to be returned for which we returns the
default settings defined in ETSI.
Note that RPN may be sent even before a dlc is opened.
> ACL Data RX: Handle 256 flags 0x02 dlen 18
Channel: 64 len 14 [PSM 3 mode 0] {chan 0}
RFCOMM: Unnumbered Info with Header Check (UIH) (0xef)
Address: 0x03 cr 1 dlci 0x00
Control: 0xef poll/final 0
Length: 10
FCS: 0x70
MCC Message type: Remote Port Negotiation Command CMD (0x24)
Length: 8
dlci 10
br 3 db 2 sb 0 p 0 pt 0 xi 0 xo 0
rtri 0 rtro 0 rtci 0 rtco 0 xon 17 xoff 19
pm 0x3f7f
< ACL Data TX: Handle 256 flags 0x00 dlen 18
Channel: 64 len 14 [PSM 3 mode 0] {chan 0}
RFCOMM: Unnumbered Info with Header Check (UIH) (0xef)
Address: 0x01 cr 0 dlci 0x00
Control: 0xef poll/final 0
Length: 10
FCS: 0xaa
MCC Message type: Remote Port Negotiation Command RSP (0x24)
Length: 8
dlci 10
br 3 db 2 sb 0 p 0 pt 0 xi 0 xo 0
rtri 0 rtro 0 rtci 0 rtco 0 xon 17 xoff 19
pm 0x3f7f
Change-Id: I73b7d8577e7e2bc3e436f4db86a91e12db440f1f
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
rfcomm_make_uih_msg() only needs session to get the role while creating
msg. This is mainly done since some commands like Test and RPN may come
even before dlc is created.
Change-Id: Ifd5a2ceaf17c20db3f00604cd2b4f1759155123e
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
l2cap_br_conn_req_reply expects valid bt_l2cap_chan pointer but this
is achieved only on accept() callback. Use l2cap_br_send_conn_rsp
instead for rejecting cases where no channel was accepted. This also
makes success path being 'primary' function path ie erros all always
handled inside if() statements.
Jira: ZEP-1405
Change-Id: I890b4fcf029afce65eba4f2ebae0b1094feb007f
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Not all users are in an ISR context where we can't block, so give the
callers the freedom to choose if they want to block or not.
Jira: ZEP-1481
Change-Id: I19bd7e2df94c4eeb60886a17a78f872bd7bea887
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds validation check when 'sdp discovery' API is to be called
by client, to reuse existing connection if valid or initiate new one
if posssible to set SDP L2CAP link to remote.
Change-Id: I47ce33cb5e95cf2616f9b23712641b912ce40f37
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Added a Pending Request structure, this will keep
a track of the last sent AVDTP Singnalling Message.
This will be used to verify the response from the remote device
Memory will be allocated by the application.
Change-Id: Ic31df154b52ce9013e5039ab195a9651d1811a7a
Signed-off-by: Arun Jagadish <arun.jagadish@intel.com>
Adds for now stubs of handlers responsible for taking a connected and
disconnected state of SDP L2CAP channel.
Change-Id: I21b76b755168fb63f6cade5f6b0c0bab93d0a01f
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Adds basic functionality to be able to trigger establishing outgoing
L2CAP channel to remote using as PSM SDP channel. The number of such
outgoing connections is limited by configured pool of connections.
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Change-Id: Ie5428e5b1b5f5c57f473ee0adfd4621cd9fe6e3e
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
This patch contains API's which is used to parse range of values
eg. (0,3). This patch also parses the string, reads, process and
move the buffer accordingly.
Change-Id: I8dba5b7d630f65b87967c101557c5c7ffd297dd1
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
If more inquiry results were received during discovery than fits in
storage results with lowest RSSI will be skipped. This is to improve
API usefulness in busy environments where results with low RSSI (likely
more far away than high RSSI) could consume provided result space,
Change-Id: I1e9ca901b693f608d58575916809e8bd8bfe710f
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
at_get_number which converts the string into number now operates on
at_client to get the string buffer. This patch also improves API()
skip_whitespace to be operated on at_client. Also the the API's
get_cmd_value, get_response_string are updated to work with buf
increment.
Also in this patch the return type of the function str_has_prefix
is changed from 'int' to 'bool'.
Change-Id: Ia626e0d13212b84413cce0444349975f4abe1cf6
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
The execution time of k_sem_give() increased slightly recently, and
since it was being called from the radio ISR this had an impact in the
deadlines not being met.
This change moves the actual call to k_sem_give() to a lower-priority
job and thus out of the ISR to avoid its execution time affecting the
ISR's timing.
Change-id: I76c82df895c6daaffef52786b0c900ee15acb0aa
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The ECC emulation synthesizes its own HCI events so we may need up to
two available priority buffers at any point in time.
Change-Id: I88b37c7e9e9f64483d80cde9243470a7f0477321
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use size_t instead of int to avoid compiler warnings.
Change-Id: I86f804010a7bd0387299648f8c2c0f880f19f580
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the ARG_UNUSED macros to some function arguments
to avoid compiler warnings.
Change-Id: Iae2cd3018c9442ffa9268fdfd33eb9a21f55087c
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
In preparation for the new Nordic MDK and nRF52840 IC support we switch
to using the SERIES config instead of the old "NRF52" macro that will be
deprecated in the new MDK.
JIRA: ZEP-1418
Change-Id: I563f025c9db9b7497116c5af23814d95c720f836
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Also remove mentions of unified kernel in various places in the kernel,
samples and documentation.
Change-Id: Ice43bc73badbe7e14bae40fd6f2a302f6528a77d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
After commit 71c7c01819 about buf pool, we
started to get spurious behaviors on various places of the code on
different boards (a101, frdm...) BUT on qemu. Basically, outgoing ip/udp
packets were full of garbage. Or sometimes it was the abilitty to parse
incoming packet that was happening.
The difference between qemu and actualy boards is - afaik, at least, let
me know if I am wrong - that qemu provide initialized memory (full of
0s). Following this asssumption, this patch just reset the nbuf right
after it got allocated. And all started to work again as thought.
It's in fact a good thing to reset nbuf memory. Even before the above
commit: after being used more than once, a buffer would have ended up
with old content, and this could have been generating a bug. So let's be
on the safe side and always intialize nbuf content.
Change-Id: I50647d9e9b82a4ed340a5ceb0d69409b0194dddd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Minimal frame size is 60 bytes, but IP frame might be smaller than this
size minus the ethernet header. In that case, Ethernet frames are padded
so it does reach this minimal size. In this case, ethernet L2 should
update the buffer list so it remove the padding length from the whole.
Change-Id: Id370cad09ad82bb54febeb60b05f7e430cc8f963
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
net_buf_put already awakes the RX thread so k_wakeup is not necessary.
Change-Id: I18b5aef5d6e85a9461bc01c17f56c3d4d9a13824
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Validate the return code of net_context_put and add debug information
in case any error is detected.
This patch fixes the error reported by Coverity:
Error handling issues (CHECKED_RETURN)
Calling "net_context_put" without checking return value
(as is done elsewhere 4 out of 5 times).
Coverity-CID: 157833
Change-Id: Ia4a87cc08094bee465c8828411d7c1311481695a
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
There are static initializer macros available for most kernel objects
which we should use whenever possible.
Change-Id: I496f4d05d26801eddd21fae53bdd4fcdc3246fe3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds H7 function implementation and test based on sample data
from Core Specification 5.0 Vol 3. Part H. Appendix D.8.
Jira: ZEP-1431
Change-Id: I49d44ee7a352d1092f6379829d747c7e0ec5e83c
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Reduce the time limit for active clock startup and increase
the CPU usage time limit before hard real-time radio
transmit/receive.
Due to isr_wrapper overhead in ARM architectures, more time
was used before hard real-time radio transmission or
reception which was detected by controller implementation
and the controller aborted the radio transactions.
This commit permits more CPU utilization by the controller
before hard real-time radio transactions start.
Change-Id: Id976add80c70cabc753c43dfac6f6603588458d9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
On CPUs like nRF51 which run at 16MHz, certain BLE control
procedure PDU processing take more CPU time than permitted
inside tIFS (150us). Current implementation of Data Length
Update procedure does not span over multiple connection
interval (unlike Encryption Setup, which is another control
procedure processing that would consume more CPU time)
hence taking more CPU time inside tIFS on nRF51.
During the radio ISR, the active clock and packet timer are
active and it is used to profile the CPU time taken which
is used to decide on whether there is sufficient time in
the current radio event to process the control packet.
This commit also fixes a potential bug that would cause
disconnection due to MIC failure on encrypted connections
that performed Data Length Update. Controller used to NACK
the request/response PDU if it was not in a state to resize
the receive buffers but did not reset the CCM counter. This
is now fixed by the change done to NACK control PDU based
on available CPU time in radio ISR.
Change-id: Id58322ad76a0dbc284738cdd9a7c0437c9e8c423
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
"next" is more relevant since its used to save next pointer
Change-Id: Ic0a8d543944681ba4291c5aa06125f565ab6115c
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
The function is not particularly small, and is used from several
places, so remove the inline declaration. This also prepares the way
for the possibility of having an application callback for letting the
application choose whether it's fine with the proposed parameters, and
thereby influence the response we send to the remote device.
Change-Id: I5848b179318b6fb6ee37fcbd479a919204f559f1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that all logging methods use printk as a backend the respective
Kconfig options should declare the right dependencies.
Change-Id: I65c759db0ec7ba6333b76d8d20aea0e374fd4947
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Moved all libc Kconfigs to where the code is and remove the default
Kconfig for selecting the minimal libc. Minimal libc is now the default
if nothing else is configured in.
Removed the options for extended libc, this obviously was restricting
features in the minimal libc without a good reason, most of the
functions are available directly when using newlib, so there is no
reason why we need to restrict those in minimal libc.
Jira: ZEP-1440
Change-Id: If0a3adf4314e2ebdf0e139dee3eb4f47ce07aa89
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Following commit fc21a76db6
Some more fixes are needed.
Change-Id: I19c2c979d44be5edfd76041d3cf4507860795c78
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using a LIFO instead of a FIFO has the potential benefit that more
recently in-use buffers may be "cache-hot" and therefore accessed
faster than least recently used (which is what we get with a FIFO).
Change-Id: I59bb083ca2e00d0d404406540f7db216742a27cf
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the user data size is now stored in the pool there's very little
value in storing it as well per-buffer.
Change-Id: I17a99123b232423c52a2179b4eccd813728d51b1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to keep the initialization process light-weight, remove
net_buf_pool_init() and instead perform the initialization of the pool
and buffers in a "lazy" manner. This means storing more information
in the pool, and removing any 'const' members from net_buf. Since
there are no more const members in net_buf the buffer array can be
declared with __noinit, which further reduces initialization overhead.
Change-Id: Ia126af101c2727c130651b697dcba99d159a1c76
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is only for use with custom destroy callbacks, so that the
application gets isolated away from the details of how exactly the
buffers are managed. This opens up the possibility of switching away
from k_fifo to potentially better solutions, such as k_lifo.
Change-Id: I0d8322fdec3500d8ae060ae471b9448aeaa4572a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
That bug never got caught because the buffer in unit test is always
clean and fully initialized to 0, and that part of the code being
tested is never used in real as the ACK reply is directly made by the
chip.
Change-Id: I88c4dd3767b4addf2250165b94f49fae29d322ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The CONFIG_TEST_RANDOM_GENERATOR parameter is not intended for
production use. Switch to CONFIG_RANDOM_GENERATOR.
Change-Id: Id6ce986259270455223ce6a42d19a3d9c9b1e642
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Until now it has been necessary to separately define a k_fifo and
an array of buffers when creating net_buf pools. This has been a bit
of an inconvenience as well as blurred the line of what exactly
constitutes the "pool".
This patch removes the NET_BUF_POOL() macro and replaces it with a
NET_BUF_POOL_DEFINE() macro that internally expands into the buffer
array and new net_buf_pool struct with a given name:
NET_BUF_POOL_DEFINE(pool_name, ...);
Having a dedicated context struct for the pool has the added benefit
that we can start moving there net_buf members that have the same
value for all buffers from the same pool. The first such member that
gets moved is the destroy callback, thus shrinking net_buf by four
bytes. Another potential candidate is the user_data_size, however
right not that's left out since it would just leave 2 bytes of padding
in net_buf (i.e. not influence its size). Another common value is
buf->size, however that one is also used by net_buf_simple and can
therefore not be moved.
This patch also splits getting buffers from a FIFO and allocating a
new buffer from a pool into two separate APIs: net_buf_get and
net_buf_alloc, thus simplifying the APIs and their usage. There is no
separate 'reserve_head' parameter anymore when allocating, rather the
user is expected to call net_buf_reserve() afterwards if something
else than 0 headroom is desired.
Change-Id: Id91b1e5c2be2deb1274dde47f5edebfe29af383a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth thread stack sizes are optimized based on the assumption
that printk is used for logging and not printf. Using _prf() (the
printf backend) risks overflowing the stack, so use the recently
exposed _vprintk instead.
Change-Id: Ibcbe0af2994c83114d12aa27a8bc29c77bb8c4c8
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now printk family from <misc/printk.h> already included should handle
BT_DBG() like expansion.
Change-Id: I5e03f786530e4bbbdb94a13a4cd77db580268c11
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Replace precision formatter (.) in printk with padding flag like %04x
since for now precision is not handled properly in printk family.
Change-Id: Ib63198e407ef584c5650d6452518b1767047630f
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
These should have been converted to using printk instead.
Change-Id: I62323704dad4fc51cc14ee4734acb6b325dcda14
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This will be used by the user to disconnect or cancel connect dlc.
This also defines an internal close function which will take
appropriate action based on the dlc state.
In case of user initiated disconnection if some pending packets are
there in queue then it has to be sent before sending DISC packet.
< ACL Data TX: Handle 256 flags 0x00 dlen 8
Channel: 64 len 4 [PSM 3 mode 0] {chan 0}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x2b cr 1 dlci 0x0a
Control: 0x53 poll/final 1
Length: 0
FCS: 0x6d
> ACL Data RX: Handle 256 flags 0x02 dlen 8
Channel: 64 len 4 [PSM 3 mode 0] {chan 0}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x29 cr 0 dlci 0x0a
Control: 0x73 poll/final 1
Length: 0
FCS: 0x26
Change-Id: Ie4fa3bd8f6b279fee6fb56ddce198d82c5047849
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
When PSM server doesn't have BR/EDR L2CAP resources to assign and handle
incoming request properly, local channel pointer may stay uninitialized.
This fixes such scenario. The fix refactors main connection request
reply handler to additional helper which can be used to send response
unconditionally for situation when local channel is not allocated
to setup L2CAP link between.
Jira: ZEP-1405
Change-Id: I5caedd63a59ad0d1704ac87fa51616a0770320bf
Signed-off-by: Arkadiusz Lichwa <arkadiusz.lichwa@tieto.com>
Instead of %4.4x we need to use %04x which printk supports.
Change-Id: I0564be5531bb266b328f77231f5d00f43eabe1ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If connection destination address has been changed update the addresses
stored by the time it disconnects since in case of RPA it is no longer
mapping to the same device after it has been disconnected.
Change-Id: I0ce966928f605a885125179eaa7b9093989825ab
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The connection destination address may change if the identity address
is resolved.
Change-Id: Id6f7b6494c24ff118043ba5f4ff54e254376eddf
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
bt_conn_lookup shall work both with identity address or initial
destination address as bt_conn may change the destination address with
the identity address.
Change-Id: Ibdd19ec453c3307eb6db188196b7e57a2260b526
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There's now snprintk available that's more light-weight on the stack
than snprintf.
Change-Id: I6b3e4409703ca92fe6b8f4146ff47c490ab826cb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Applications may want finer control of the NRPA used for
non-connectable beacons, and provide it up-front rather than letting
the stack generate one.
Change-Id: I84d459372cc85ed09a8f9cde16dbb9b98dec2a43
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Expose helpers in hci.h for setting and getting the LE random address
type.
Change-Id: I7c6437051f0b2d1f5f79e19b2616bb643ae6300b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: I4d6f635a0ed61de698727028ea8767dc0ef28bb1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: Iab7cc6da110e9c98720211a6f773dcf055a3a411
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This commit improves source code readability by breaking long
expressions found at some if statements.
Some minor style issues are also fixed by this patch.
Change-Id: I0c8e42eaf0fca3a98490c54a0ccb941766c50fa3
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Instead of having custom logic for determining the minimum of two
values, use the existing min() helper from misc/util.h.
Change-Id: I9809883d4a31126329373f293897dd49eb91e9ad
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
rfcomm_dlc_drop() can be used from many places to unlink dlc
from session and destroy it. So it is better to send DM
explicitly from relevant places.
Change-Id: I9b6a31ce5bb65b90510aa483539d4a201ba12b60
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
When the Controller is configured to support less than 251
as the supported maximum data length, missing check caused
the Controller to incorrectly re-initialize its rx buffers
causing assert during the DLE procedure. This commit fixes
the procedure to correctly use the supported maximum length
if the peer requests a transmit length that exceeds the
supported receive length.
Change-id: I6ad7196e3db44b303ddf2ec06e0ae579bf2eb774
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This allows to fine tune TX stacks size depending on selected HCI
driver. If needed it can be used to tune for monitor too or other
logging mechanism used.
Change-Id: Ib501921da0b786e151083760d85ec58fe3c08b60
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
If debugs are disabled scid and dcid variables were never read.
This also fix mixed values of scid and dcid in le_disconn_req.
Change-Id: I3b435dd0640c5c65ab5fe68e33dd25e3c9e0026e
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
subsys/bluetooth/host/hci_ecc.c: At top level:
subsys/bluetooth/host/hci_ecc.c:277:6: warning: no previous prototype
for 'bt_hci_ecc_init' [-Wmissing-prototypes]
void bt_hci_ecc_init(void)
^
CC subsys/bluetooth/host/conn.o
Change-Id: I920d8b6b66c82be932c579461310505c6d402c08
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Even one-line branches should have {}, and the last two return
statements can be simplified into a single one.
Change-Id: I0f65aeaba867240255eae8e1c461386700444ae6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With k_sem API it is possible to specify maximum sempahore value
so we no longer need to track semaphore count.
Change-Id: I86744ba63bd3207051ca3466d4f81b816d24f5ad
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Applications expect service end handle as attribute value in userdata
on discovery response callback.
Jira: ZEP-1354
Change-Id: I664da4a7e054a531ad1c2c8cbc74367cb679ff03
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Security needs to be elevated based on dlc required sec_level
before creating dlc. If L2CAP connection is not created then
setting dlc required sec_level to chan would do the job.
Change-Id: I21debd3559c9ccfb79011160d676932bc2a54604
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Correct the local LE supported features bitmap to actually "or"
together all the bits that correspond to the set of features that
are implemented at this time.
Change-Id: I0c62ec566c775514250fcf062aeef6c9656719e3
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
If the original buffer cannot be reused, either by no having enough
space for user data or if is fragmented, it can in fact be smaller than
both the segment buffer and MPS.
Change-Id: I59a537aff59c5d56b2883e9bd51f3a1a3932d348
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The segments need to be limited by the minimun of the segment buffer
tailroom and tx MPS not the original buf length.
Change-Id: I580a3bb61aa190ac0cdd3717bc06fd6e6e668304
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Implement the 2 HCI commands that provide ECC public key
and shared secret generation:
- LE Read Local P-256 Public Key
- LE Generate DHKey
Jira: ZEP-1246
Change-Id: I79388bfdb9f2e28b9377b4bb6ee2caca25f33f3e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Structures attribute need to be ordered according to endianness.
Change-Id: Ib3053728cbc49e54631057c779aba0f16aace283
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Certain structures and defines in this file are from
from mbed's implementation. The file header is updated
as per this.
Change-Id: I688917cdd17cfc8b27d5b78181ced90df73c9efd
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
- {} are always required on if/for/while
- no break line before an if, if condition is testing previous
assignment
- parameters indentation etc...
Change-Id: I83f217c02733b9e63ef1e752f55937f3d7dc03e1
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
s/nano_sem/k_sem + some necessary changes for the k_sem to work.
Change-Id: I96377083f5e17631b63d6da1a0546966ec95ff8b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Handle the scenarios like ignoring a response in non existing dlc,
correctly handle if received a command with invalid mtu etc.
Change-Id: Ib0bce9134bac3a0dead03798f859af54873a70c1
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
k_sem_take return differ from nano_sem_take since it return 0 for
successful case instead of 1.
Change-Id: Ia39cd624d56dbc1c8e7f3558244bebf765da191d
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is no longer needed after switch to unified kernel.
Change-Id: Ie1f8dadb3f2e43ae6ccfbfaf1f754196f3237471
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
After switch to unified kernel this is no longer needed.
Change-Id: If9877d3fa038dd873011fb780c7e767e150647ae
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This fixes defect found by coverity: 152027 Pointer to local outside
scope.
Change-Id: I50f196a04363ffa6e6654b71a9a1d89034580413
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Implement the 3 missing HCI commands required to support
Data Length Extensions:
- LE Read Suggested Default Data Length
- LE Write Suggested Default Data Length
- LE Read Maximum Data Length
Note: Only octets are actually used at this time, not time.
Jira: ZEP-1246
Change-Id: Id76d8fedb5ecaf0001c8429cf22f9a3e2c910a44
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix Coverity, sizeof not portable, defect; by explicitly
using sizeof(void *).
suspicious_sizeof:
Passing argument mem_head of type void ** and argument 4U
/* sizeof (mem_head) */ to function memcpy is suspicious.
In this case, sizeof (void **) is equal to sizeof
(void *), but this is not a portable assumption.
Change-id: I4b4776466e16020876500feba0141985b8581017
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
External interrupts are indexed from value 16, wherein
0 to 15 are ARM cortex M exceptions. Fixed code in
_irq_is_priority_equal to fetch correct external
interrupt line ISR priority.
Change-id: I9cfd411480e78dfc9635e72d14df9d667a9d8400
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Coverity analysis discovered NULL pointer being
dereferenced when passing a auto variable. The variable is
now correctly assigned with address of a valid default
value variable. As per design, the dereferencing will not
happen as the master role does not use the passed parameter
only slave role uses it to prepare the connection parameter
request PDU.
Change-id: I3f8519b23a83cb8c50c7fba81810eff7737ff74a
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Coverity analysis discovered that observer filter policy
field was 1 bit, whereas valid range for extended scanner
filter policy feature implemented in controller is 0 to 3.
Increase the bit field size from 1 to 2.
Change-Id: Id4b2e354961dfb3b45f72fa4e0ab18de7425bbb5
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This fix using incorrect address type for passive scanning with
privacy enabled. Controller was not reporting directed advertising
to RPA address due to public type being used for passive scan.
This was affecting TC_CONN_GCEP_BV_01_C, TC_CONN_ACEP_BV_01_C and
TC_CONN_DCEP_BV_01_C qualification test cases.
Jira: ZEP-1200
Change-Id: Icc316441fcac1a72d75f9ade27a99030efc846b9
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This might create confusions when debugging as usually the prefix is
associated with the file or layer.
Change-Id: Ibf45578c1f54a4bec896acd6042589c815216e1f
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BR/EDR code should have minimal impact on LE code so to keep it simple
just require peripheral and central to be enabled when selecting BR/EDR
support.
Fix following Kconfig warning:
warning: (NETWORKING_WITH_BT && BLUETOOTH_BREDR) selects
BLUETOOTH_L2CAP_DYNAMIC_CHANNEL which has unmet direct dependencies
(BLUETOOTH && BLUETOOTH_HCI && BLUETOOTH_HCI_HOST && BLUETOOTH_CONN
&& BLUETOOTH_SMP)
Change-Id: I7f7cb8794def0df6daaa4abfe4596df460f1a2b2
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Fix following warning:
CC subsys/bluetooth/host/monitor.o
In file included from zephyr/include/drivers/loapic.h:58:0,
from zephyr/include/drivers/ioapic.h:22,
from zephyr/include/drivers/sysapic.h:20,
from zephyr/include/arch/x86/irq_controller.h:33,
from zephyr/include/arch/x86/arch.h:28,
from zephyr/include/arch/cpu.h:23,
from zephyr/include/kernel.h:2458,
from zephyr/include/zephyr.h:20,
from zephyr/subsys/bluetooth/host/monitor.c:24:
zephyr/subsys/bluetooth/host/monitor.c: In function
'_deprecation_check_sys_init_bt_monitor_init0':
zephyr/include/device.h:130:16: warning: '_INIT_LEVEL_PRIMARY' is
deprecated [-Wdeprecated-declarations]
static struct device_config _CONCAT(__config_, dev_name) __used \
^
zephyr/include/device.h:245:2: note: in expansion of macro
'DEVICE_AND_API_INIT'
DEVICE_AND_API_INIT(dev_name, drv_name, init_fn, data, cfg_info, \
^
zephyr/include/init.h:69:2: note: in expansion of macro 'DEVICE_INIT'
DEVICE_INIT(_SYS_NAME(init_fn), "", init_fn, NULL, NULL, level, prio)
^
zephyr/subsys/bluetooth/host/monitor.c:193:1: note: in expansion of
macro 'SYS_INIT'
SYS_INIT(bt_monitor_init, PRIMARY, MONITOR_INIT_PRIORITY);
^
zephyr/include/device.h:48:31: note: declared here
static __deprecated const int _INIT_LEVEL_PRIMARY = 1;
Change-Id: Ie903e3a075f6614b26018be5769be3651f0963be
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Added implementation for HCI Reset Command. Implementation
gracefully disables any running advertiser, observer, and/
or connection roles, and it resets controller context members.
The HCI Reset Command is implemented in such a way that
driver instances shared with other sub-systems and
application is not disturbed and instance/references used
by Bluetooth Controller are gracefully returned back.
Jira: ZEP-1282
Change-id: Ifb9ae6807736b5ec2d9f346cf2a590322056bcee
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This fixes issue that L2CAP Connection Parameters Update Request was
not sent. There was check that used LE features of host controller
to determine if L2CAP procedure or LL shall be used. It was failing
with 4.2 controller. The check shall test if remote supports
LL Connection Parameters Request Procedure. If it's not supported,
then L2CAP Connection Parameters Update Procedure will be used.
Closes ZEP-1220
1/4 L2CAP TC_LE_CPU_BV_01_C PASS
2/4 GAP TC_CONN_CPUP_BV_01_C PASS
3/4 GAP TC_CONN_CPUP_BV_02_C PASS
4/4 GAP TC_CONN_CPUP_BV_03_C PASS
Change-Id: I61ad544d9568ca6306a845e05c1a2e28d1693ab4
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
Using the K_* macros makes it easier to read what exactly the various
timeouts are.
Change-Id: Ia405d3760b8e600af7e33a7221ef6ec717708973
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch left-over usage of TICKS_NONE and TICKS_UNLIMITED to the new
unified kernel counterparts K_NO_WAIT and K_FOREVER.
Change-Id: I2f2a16360e816f9f8791eb216deb3c70b8cc87df
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add support for console output via the USB UART.
Note that console input via the USB UART doesnt work.
Adds a simulated poll method for UART interface exposed by USB.
Jira : ZEP-775
Change-Id: I357827ea52c027eb000baed80225f422df1f3358
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
During the initial integration of controller to Zephyr OS,
radio hardware access was abstracted out into hal/radio.c
file. Bug introduced in hal/radio.c has been fixed so that
whitelist feature works again.
Change-id: Ie5faf80b1a008ef326613548a5a28a4ba52e7ef7
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The conditional defaults must come last in order to be properly
processed.
Change-Id: Id7a152ca1a1584935029e212d0dd8f37494d1cf4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add implementation in HCI and Controller to support
HCI_LE_Remove_Device_From_White_List, as it is listed as
mandatory under BT Spec. v4.2, Part E, Section 3.19 LE
Controller Requirements.
Change-id: Icef88dffc85746f3cc7adb7fb692ae5578274ed2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Rename left-over mentions in code comments of "fiber" to "thread".
Change-Id: I1af1baf99652434e90eb491c10238b94d26d341d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch from fiber_start() to k_thread_spawn() and from NANOKERNEL to
POST_KERNEL init level.
Change-Id: I34fb11cbe20216c8646ebacb07be304a67e3cd0a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use k_thread_spawn() instead of the deprecated fiber_start() API.
Change-Id: I42e798ef3a4276863659c8d97c85224a652be1fd
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_recv() function had protections for being called from a
preemptible task context, however nothing was protecting preemption by
ISR. A fairly simple fix is to protect the couple of critical regions
that can be reached from bt_recv() with the help of irq_lock().
Change-Id: Ifc29fd31205eb5425e1b7c862347d9420688df4e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch to using the unified kernel k_thread_spawn() API instead of
nano_fiber_start().
Change-Id: I325cf467ae2a52c6aec8fc166397c323929e3013
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the unified kernel API k_yield() instead of fiber_yield().
Change-Id: I8f52031f52f7ac8783033a51751dc22decdfa59a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch to using k_uptime_get() instead of the deprecated
sys_tick_get_32() API.
Change-Id: I737ef0153eff9d283bae840ff5177f8132396e1b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use defines from k_fifo intead of legacy API.
Change-Id: Ib8cf0d88240ef145da550b8cf83d2580e7140521
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Those are lefovers from nano_delayed_work usage.
Change-Id: I3f17c7b89b1fa946495e160732457500e2f74f25
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This fixes warnings related to the use of nano_work and
nano_delayed_work in HCI layer.
Note that k_delayed_work takes a timeout in miliseconds rather than in
ticks thus the timeout values have been changed.
Change-Id: I953a82a6aa613bb1072a8ad4b01e0f94e5cd64bd
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes warnings related to the use of nano_work and
nano_delayed_work in bt_conn layer.
Note that k_delayed_work takes a timeout in miliseconds rather than in
ticks thus the timeout values have been changed.
Change-Id: Ia8f34b475051515fd74000cce745ad226aa18aa5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes warnings related to the use of nano_work and
nano_delayed_work in SMP layer.
Note that k_delayed_work takes a timeout in miliseconds rather than in
ticks thus the timeout values have been changed.
Change-Id: Ida58ff0f609dc2a8fd415692bc2cec91eb56a294
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes warnings related to the use of nano_work and
nano_delayed_work in ATT layer.
Note that k_delayed_work takes a timeout in miliseconds rather than in
ticks thus the timeouts values changes.
Change-Id: I14d8438c1537febcb7768ef2934042ce38682739
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes warnings related to the use of nano_work and
nano_delayed_work in L2CAP layer.
Note that k_delayed_work takes a timeout in miliseconds rather than in
ticks thus the timeouts values changes.
Change-Id: I1e3bd7857248865e34a313dd42862af5f4e3805b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently the ideal buffer counts for a controller-only build are 6 RX
buffers and 7 TX buffers: ATT_MTU of 158 bytes can be sent in one
connection interval of 6 tx/rx -es wherein connection interval is
7.5ms
Change-Id: I64b4620c5e8e7db8d7ed72fa1db82e266e121f27
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces the Connect API which initiates session
connection first. If session is already there with the peer
then it has to reuse it and initiate DLC (which will be done
in the subsequent patch) since there can be only one session
per device.
< ACL Data TX: Handle 256 flags 0x00 dlen 8
Channel: 64 len 4 [PSM 3 mode 0] {chan 0}
RFCOMM: Set Async Balance Mode (SABM) (0x2f)
Address: 0x03 cr 1 dlci 0x00
Control: 0x3f poll/final 1
Length: 0
FCS: 0x1c
> ACL Data RX: Handle 256 flags 0x02 dlen 8
Channel: 64 len 4 [PSM 3 mode 0] {chan 0}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
Change-Id: I9828e0f3b3ea43bb17df95f0536e15df86f1b4be
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
In some SMP + GATT scenarios it's possible we get up to 6 incoming ACL
packets. To handle these efficiently, and more importantly, to not
have to drop data if the controller lacks host flow control (as is the
case currently with Zephyr-based controllers), increase the default
from 5 to 6.
For a controller-build it makes sense to just match up with the
controller-side configured RX buffers.
Change-Id: Id44fa724597b88a51f9085dac009e8d84a439bfc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All boolean options default to 'n' without the need to explicitly
state this. It's only the cases where we want 'default y' where we
need to state this.
Change-Id: I47dbda62462ea437a2423b8508ea2cc640a22e41
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Restructure the Bluetooth options more logically.
- Both host and controller are now behind the same high level
CONFIG_BLUETOOTH.
- Selecting controller support disables other HCI driver selection, so
the controller isn't in the same list as HCI drivers any more.
- Under the top-level there's a "Custom stack" option, which when
enabled opens up the option of choosing CONFIG_NBLE.
There are various other cleanups and simplifications in this patch as
well, since splitting these up would have been fairly tricky while
making sure all test cases still build.
Change-Id: I5bb715cb9d20201cb8b72fbd149c8a09a4b2d7d2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This should be particularly useful with the recently added controller
assert functionality that causes vendor events with debug information.
Change-Id: Ied0df2ff414e08c11a73cca0afba4dc04b0b8625
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When building Zephyr in the controller-only configuration,
assertions that happen in the Link Layer code are not visible
to the Host which is running on another HCI and connected via
UART or USB to it. This patch allows the Controller code
to output the assertion line number when in such a configuration,
allowing the Host to view the event to help debugging.
The event format used is temporary and will be replaced by a
standardized Vendor Specific specification to come at a later
time.
Change-Id: I013ca6783a3fdedc47b171132919dd4798c66285
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The right convention for help text is tab + 2 spaces.
Change-Id: I2722a8b33f5f74be110dc43fbcecc12841f0db84
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When retrying the request due to a security error that can fail but since
the original buffer was freed in the process the code can no longer verify
if the opcode matches thus it always fails BT_ATT_ERR_UNLIKELY instead of
using the response error, so this not longer cares about the opcode and
just use the response error always.
JIRA: ZEP-1195
Change-Id: I1149b993b97733ab5bb00f347e4f973647e0fdd4
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This consolidate code around LE signalling header handling which has been
duplicated in many places.
Change-Id: I0c2cd48c155b751e1bbbd26070965d075cdc2cc5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When a peer controller does not recognize one of the LL control
PDUs received, it will issue an LL_UNKNOWN_RSP PDU to let the
peer know that it does not recognize the request.
The controller now handles this incoming PDU and completes the
procedure by issuing the appropriate HCI event in the case of
an LL_FEATURE_REQ and _RSP pair.
Jira: ZEP-1220
Change-Id: I7c04a346441f04deee41198daa6309c11ae1b571
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
'private' is a C++ reserved word and will lead to compilation errors:
C++ ble.o
In file included from ble.cpp:7:0:
include/bluetooth/bluetooth.h:284:10: error: expected unqualified-id before 'private'
uint8_t private[4];
Change-Id: I36aef5a84af4fc66e1c810bd0c56e5ab5f803294
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In function at_get_number check for the value if gets computed.
If not return error. Also change the end state handling.
Change-Id: I193b04fa2880dfb44e7727b30b67c1ec2e051cc7
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Add an implementation for the bt_storage_clear() API.
Jira: ZEP-181
Change-Id: Iae01c571c161317ea0cc44513d108301c7b5a069
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add basic implementation of an internal storage handler that uses the
local file system. The root directory for all Bluetooth related data
is /bt. Each remote device has its own subdirectory and each key its
own file. This helps keep the implementation very simple, but does
come with the meta-data overhead for each file.
As an example, the value of a key 0x0001 for a device with a static
random address cc:11:22:33:44:55 would be stored in the following
file: /bt/cc11223344551/0001. Local values such as the identity
address are stored directly under /bt with a file name that matches
the key the same way as remote-device files.
For full functionality the implementation requires a file system that
can support file/directory names of up to 13 characters in length. If
the file system supports less than that (as is the case with FAT12)
then only local values can be stored (in /bt/abcd). Local values
include the identity address as well as the local IRK.
Jira: ZEP-181
Change-Id: I7dc696af6353a154cb00dcd01a5f4ac3d7127e6b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is not needed for Zephyr controller build and should already
be fixed in Mynewt.
Change-Id: I39e81dc3e9b5fd5a3f5f823465527248625caf26
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Patch 8c118f8673 causes the wrong semaphore
to checked so receiving credits are never restored which caused the
channel to get stuck after all the credits are consumed.
JIRA: ZEP-1199
Change-Id: I9cd5474b3bcaafcb19d15613939ce30d07befe0a
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements USB Mass Storage device Class,
which allows the Zephyr target Board to appear
as a USB drive to a host.
This code would invoke disk_read() /disk_write()
hooks which are to be provided by the storage
layer.
The Mass Storage protocol state machine is based on
mbed's implementation. We augment it by adding Zephyr's
USB transport and Storage APIs, and offload disk ops
to a fiber context rather than in the USB irq context.
origin: https://developer.mbed.org/users/mbed_official/code/USBDevice/file/01321bd6ff89/USBMSD
Jira: ZEP-233
Change-Id: I8199598c76da20ab20012d81dac7615f6a366303
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
USB class drivers may need to offload some work from
upcall interrupt context to a background fiber. This
requires some way to defer taking more data from host
till the offloaded work completes. Two APIs are added to
achieve this.
Further USB class drivers sometimes need to set STALL condition
on end-points to signal errors to host.These too are
added.
Change-Id: Ic973522c3394e23d7f9c4c67affc0cd050afc20f
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
This patch removes "FAT" from files names, config names and
symbol names so as to avoid confusion, when other modules use
them in a more generic way.
Also flash_disk_access.c and ram_disk_access.c now exports generic
disk_access symbols as defined in include/disk_access.h rather
than FAT specific ones in fs/fat_diskio.h. Thus modules like
USB which need to use disk_access interface is not dependent
on symbols from ELMChan FAT module. Also fat_diskio.h
is removed.
Further the shim between ELM chan and Zephyr is modified as
per these changes.
Change-Id: Ifd80f14a629e467ee9c7a9aaff8a4896eed11982
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Add a simple shell that allows exploring the contents of the file
system.
Jira: ZEP-1235
Change-Id: Iaa49f0be18980dd740e9552ddf4761196a818884
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove hardcoded use of crystal as 32KHz clock source and
20 ppm accuracy; and use the values from config for sleep
clock source and sleep clock accuracy value in Bluetooth
Controller.
Change-id: I1c0d53ecf8ad158153d5186a6680b5eb03d1641b
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Making a reference to the common work queue code should not necessarily
drag in the system workqueue, since it is possible to use a workqueue
that is not the system workqueue. This is done by moving the system
workqueue into its own code module.
Moving the system workqueue to its own code module allows removing the
NANO_WORKQUEUE and SYSTEM_WORKQUEUE kconfig options, and compiling the
common workqueue code and system workqueue all the time. They are only
linked in the final image if a reference to them exist, same as the
other kernel modules.
Change-Id: I6f48d2542bda24f4702e7c2e317818dd082b3c11
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Provide more detailed information about the controller address and
version upon init when debug is enabled.
Change-Id: I5fe9c7c91f95928cb3cc64b801137bb1466e4115
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
During implementation of alternate encryption procedure
usable in nRF51, commited in
c41d3edda8, re-encryption
procedure was broken. This commit fixes the issue, and
now re-encryption should work on both nRF51 and nRF52.
Change-id: Ia41200f42b1d46e1f3f35ff44b582d4ffcc5f4fa
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
So that application could check data pointer to see if any
data have been received and if read operation is complete.
Change-Id: I36c3ff81baefbc535374d937e5297938445eafa6
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
This makes use of the same code used by LE to print the state transitions.
Change-Id: I90a04f3c3f426fde1e0987acb572f7371c483c1c
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a common function to log state transitions including the caller
function and line in case something goes wrong:
[bt] [DBG] bt_l2cap_chan_disconnect: (0x0011b14c) chan 0x001199c0 scid 0x0040 dcid 0x0040
[bt] [DBG] bt_l2cap_chan_set_state_debug: (0x0011b14c) chan 0x001199c0 psm 0x0080 connect -> disconnect
[bt] [WRN] bt_l2cap_chan_set_state_debug: bt_l2cap_chan_disconnect()1562: invalid transition
Change-Id: I246a9004a04d93a38b8c7f7633705f6c191698b2
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Channel state shall be updated properly otherwise it may cause unexpected
errors.
Change-Id: Ifd54d6bd3c5b44a40c315fd8a2946b30168aa65f
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This defines and clarifies PF bit macro for both UIH and
non UIH packets.
Change-Id: Ide7736c0fc8607708824766adbfccf1bd7bc48e9
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Security will be elevated based on the DLC required level
during connection.
Change-Id: I0b63885582f34a5689f7bc8081c1f9f011b2325f
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Initialize the variable to zero before computing.
Change-Id: Iccdf77a085667728dbb68779f001c8d940a7a89d
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
This is necessary in order to properly handle security errors which are
part of the testing specification thus can influence qualification.
Change-Id: If444e753be9196f3d5bb36cea00e332a33aa249f
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This is to avoid code duplication while implementing outgoing
connection.
Change-Id: I52f882b7be9180f29def59c8ac3ef0a4798b719d
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
This is to avoid code duplication while implementing outgoing
connection.
This also moves setting initiator flag while allocating, than
doing it when SABM is received.
Change-Id: I8e811c995bf0eaa0bd24715e2e96d8a578a79c5d
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
This replaces initiator flag of session and dlc to enum which has
two values INITIATOR and ACCEPTOR.
Also this defines macros for CRs in header. Basically there are
three types fo CRs. Frame header CR has different meaning for
UIH and non UIH packets. Also this renames the existing msg hdr
CR to make it consistent.
These changes are basically done to make it more readable
Change-Id: Ic15e93465b0afbd19d8805f27d7a43f34ef38689
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Move controller code from drivers/controller to
subsys/bluetooth/controller.
Change-Id: I73f675188485aa3267507bad7647796e593a3da0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move the Bluetooth host stack from net/bluetooth to
subsys/bluetooth/host. This is preparation for having both host and
controller under the same root, i.e. subsys/bluetooth/.
Change-Id: I3bc796f7e331fca0c485f3890d62b9c03e027b96
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
FS_FAT_FLASH_DISK_W25QXXDV is a boolean so "" makes no sense.
Change-Id: Ic43529928d80bcd76c2876219990bcec86657d3d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The flash and RAM disk options are mutually exclusive (evident e.g. in
both defining FS_VOLUME_SIZE and FS_BLOCK_SIZE variables), so they
should really be inside a choice-endchoice block. The duplicated
options can also taken care of with a single definition using
conditional default values.
Change-Id: I87733f0c342166a9e03aa0e1f34390d91107b137
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The namespace allocated for the filesystem API is fs_* and FS_*. That
means all symbols and defines should adhere to it.
Jira: ZEP-1155
Change-Id: I422310448b7c7c347f621aea6d7b1d97ef25c94d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Subsystems code will reside in subsys/ folder. This patch creates the
folder and moves FS code there.
Jira: ZEP-1120
Change-Id: If3b1bcb996c5fbd4056cd5d1920d41d29810d6b2
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
