This adds support for the flash peripheral found in the SAME5x/SAMD5x
line of MCUs.
The peripheral is very simmilar to the one found on SAMD2x with only
a few register names changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Refactors the mcux gpt driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux igpio driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpuart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds BME280 SPI chip select pin control if chip select is
configured for the device in the device tree.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Need to set device busy when enter into transceive function
in SPI DW driver.
In current SPI DW driver the transceive function don't set busy state,
but that is important for PM busy state.
This will lead to unexpected behaviors when system calls this
function and enter into idle state.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Prior to this you would get compilation error when building
samples for the nrf5340_dk_nrf5340_cpuappns board.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
This commit adds SPI driver and its bindings using the USART peripheral
for Silicon Labs EFM32 and EFR32 MCUs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
calling UARTE power management with DEVICE_PM_SUSPEND_STATE
then DEVICE_PM_OFF_STATE causes a deadlock in while loop.
It waits for an event witch never comes
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
EEPROM simulator and native_posix have been unified to one solution,
the old eeprom,native_posix is removed.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a eeprom simulator. The PR limits the addition to
qemu_x86 but it can easily be added to other devices by defining the
eeprom simulator in the dts and setting 'CONFIG_EEPROM_SIMULATOR=y'
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In STM32 flash driver, don't use semaphore if multithreading
isn't defined.
If multithreading isn't defined, a call to sem_give function
generates a hardware fault exception.
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Add driver for the Texas Instruments LMP90xxx series of multi-channel,
low-power 16-/24-bit sensor analog frontends (AFEs).
The functionality is split into two drivers; an ADC driver and a GPIO
driver.
Tested with LMP90080 and LMP90100.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Before establishing the ppp connection, windows sends the string CLIENT
and expects the reply CLIENTSERVER from the modem.
This functionality is implemented in the new function
ppp_handle_client().
This feature must be enabled via Kconfig.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Correct handling of device encoded temperature values, which combine a
12-bit 2s complement signed value with a separate sign bit. Rework
conversion between device and sensor temperature representations to
support negative temperatures in both domains.
Use a much simpler trigger configuration where the alert is driven by
comparator output, rather than as an interrupt that requires a pair of
I2C transactions to read and clear the flag.
Refactor the trigger infrastructure to use the setup/handle/process
idiom, which reduces duplicated code and to correctly detect alerts
present when the triggers are set.
Completely replace the sample with something that demonstrates
updating upper and lower threshold values to track moving
temperatures.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Added autocompletion to 'sensor get' command. After this change
device and channels are autocompleted. It is possible to provide
multiple channels for reading.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When asserts were disabled then sensor accepted any channel in
hts221_channel_get(). Changed to return -ENOTSUP when invalid
channel is provided.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
MPU6050 no longer using Kconfig to specify I2C addresses. Reference
to the removed symbol causes QA diagnostics. Remove the reference;
when AK8975 is converted to devicetree it may be possible to restore
the link between the sensors.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a binding for the sensor and replace all Kconfig selection of
hardware parameters with devicetree property values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
echo_server app doesn't compile (it uses minimal libc which lacks
unistd.h), let's switch to a more fine-grained include here.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
PWM driver for LiteX SoC builder was created.
Because LiteX supports only one channel for each PWM device,
an appropriate restriction was made.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This adds I2C bitbang driver for LiteX SoC builder with its bindings.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add support for specifying the PWM signal polarity through flags to
the NXP Kinetis FlexTimer (FTM) PWM driver.
Prior to this change the FTM PWM driver always produced inverted
polarity (active-low) PWM signals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for requesting an inverted PWM pulse (active-low) when
setting up the period and pulse width of a PWM pin. This is useful
when driving external, active-low circuitry (e.g. an LED) with a PWM
signal.
All in-tree PWM drivers is updated to match the new API signature, but
no driver support for inverted PWM signals is added yet.
All in-tree PWM consumers are updated to pass a flags value of 0
(0 meaning default, which is normal PWM polarity).
Fixes#21384.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The rf2xx driver needs GPIO driver to works. The RST, SLPTR and INT
are mandatory signals and driver uses DT to configure them. This add
the GPIO dependency on Kconfig.rf2xx file.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Do not enable hardware accelerated checksum calculation by
default. It does not work for frdm-k64f and is causing
confusion among users.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A directive to compile the system call handlers for the
watchdog subsystem was omitted from CMakeLists.txt, causing
the handlers not to be compiled and some issues in the C
file undetected.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Made the unnamed choice for ST7789V pixel formats named so that the
default value can be set in defconfig files.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
This adds PRBS ranom number generator driver for
LiteX SoC builder with its bindings.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
miv already had it defined, but let's shorten the names and use
them in the driver. This also adds it for sifive-freedom.
Signed-off-by: Olof Johansson <olof@lixom.net>
This is no longer needed, since all in-tree platforms are only using
the standard mstatus formats. Remove it to avoid the complexity.
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert the NXP MCUX FTM driver to use the DT_INST_* defines instead
of a mix of CONFIG_PWM_* and dts fixups. This simplifies adding new
device tree properties to the ftm nodes.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Only emit a warning about changing PWM period for all channels of a
given FTM instance when changing the period from zero to
non-zero. This silences the useless warning issued at first FTM PWM
channel configuration.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Don't sleep 50ms after each received packet, sleep only when there
wasn't anything to receive. Otherwise data could get stuck for a long
time if there was more than 20 packets coming in per second. The
read() call on a TUN/TAP device returns only a single packet per call.
Also remove the call to eth_stats_update_errors_rx() because this else
clause isn't actually a receive error, we're just waiting for more
packets.
Signed-off-by: Jonas Norling <jonas.norling@greeneggs.se>
The current configuration causes the STM32 flash support always to be
built, even if an unrelated flash driver, by example the SPI_NOR driver
is selected.
This behaviour gets especially problematic (build failure) if the flash
hardware of the given MCU is not supported (e.g. STM32F2).
The suggested change should ensure that STM32 flash support only is
built when it actually is selected.
Signed-off-by: Marco Peter <marco@peter-net.ch>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced SPI_MCUX_FLEXCOMM
symbol.
Also clean up the header to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit 41713244b3 ("kconfig: Remove '# Hidden' comments
on promptless symbols"). I forgot to do a case-insensitive search.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
