Cleanup around COND_CODE_1 usage and replacing with
IF_ENABLED if applicable.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Low frequency and high frequency clocks had separate devices
while they are actually handled by single peripheral with single
interrupt. The split was done probably because opaque subsys
argument in the API was used for other purposes and there was
no way to pass the information which clock should be controlled.
Implementation changes some time ago and subsys parameter was
no longer used. It now can be used to indicate which clock should
be controlled.
Change become necessary when nrf5340 is taken into account where
there are more clocks and current approach would lead to create
multiple devices - mess.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
OpenThread recently introduced CMake build system into its repostiory
so we no longer need autotools to build OpenThread libraries and can
integrate them natively.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
NRF devices hardware has flash protection which doesn't
reflect flash API definition well. So fare protection
mechanism was emulated by the software and the driver deals
with hardware flash protection on its own.
Recent change to protection behavior requirement allows
to remove flash API behavior emulation at all.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Setting EEPROM_STM32 with `default y` under `if SOC_FAMILY_STM32`
overrides `depends on SOC_SERIES_STM32L1X` in EEPROM_STM32
definition.
Then, if ever EEPROM is set in any file (as in
tests/drivers/build_all`), EEPROM_STM32 will be indeed set,
with potential issues on series where driver is not yet correctly
handled.
Fix this by removing EEPROM_STM32 definition in STM32 generic
file and set `default y` along with the `depends on` to keep
it effective.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Uses the generated device tree macros, DT_NXP_LPC_USART_USART_*, in the
mcux flexcomm driver and removes the now unused dts fixups from the
lpc54xxx and lpc55xxx socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the lpc usart shim driver to more accurately reflect the
flexcomm hardware IP and to prepare for instantiating it on an SoC
outside the LPC family.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add initial Atmel at86rf2xx transceiver driver. This driver uses device
tree to configure the physical interface. The driver had capability to
use multiple transceiver and systems with multiple bands can be used.
With this, 2.4GHz ISM and Sub-Giga can be used simultaneous.
Below a valid DT example. This samples assume same SPI port with two
transceivers.
&spi0 {
status = "okay";
label = "SPI_RF2XX";
cs-gpios = <&porta 31 0 &porta 30 0>;
rf2xx@0 {
compatible = "atmel,rf2xx";
reg = <0x0>;
label = "RF2XX_0";
spi-max-frequency = <7800000>;
irq-gpios = <&portb 2 0>;
reset-gpios = <&porta 3 0>;
slptr-gpios = <&portb 3 0>;
status = "okay";
};
rf2xx@1 {
compatible = "atmel,rf2xx";
reg = <0x1>;
label = "RF2XX_1";
spi-max-frequency = <7800000>;
irq-gpios = <&portb 4 0>;
reset-gpios = <&porta 4 0>;
slptr-gpios = <&portb 4 0>;
status = "okay";
};
};
At the moment driver assume two transceiver are enouth for majority of
appications. Sub-Giga band will be enabled in future.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
It is possible that the network interface is not yet initialized
when status of the PHY changes. In this case we must not call
net_eth_carrier_on() as that will cause a crash.
This was noticed with mimxrt1050_evk board.
Fixes: #21257
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Enable ESPI OOB channel by default in XEC driver.
Enable OOB channel transmit interrupt and handle OOB up/down correctly.
Change interrupt clearing, clear low level interrupt bits in subhandlers
and high level interrupt in aggregate handlers at the end.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
MCHP I2C spec recommends that for repeated start update control register
De-assert ACK in preparation for NACK to end transfer.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Newer SoCs like SAME54 provide dedicated registers to store
the USB trim configuration.
Use those registers if they are defined in ASF to access the
calibration data.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
On newer sam0 SoCs peripherals are enabled through the MCLK
instead of the PM register.
Use the MCLK register if it's availiable.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Newer SoCs like SAME54 have multiple IRQs for the USB peripheral.
Automatically enable all IRQs configured in the DTS.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Adds a shim layer around the mcux lpc flexcomm driver to adapt it to the
zephyr spi interface. It leverages heavily from the existing mcux dspi
shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GIC-400 driver currently only supports SPIs because the (32) offset
for the INTIDs is hard-coded in the driver. At the driver level there is
no really difference between PPIs and SPIs so we can easily extend the
driver to support PPIs as well.
This is useful if we want to add support for the ARM Generic Timers that
use INTIDs in the PPI range.
SPI interrupts are in the range [0-987]. PPI interrupts are in the range
[0-15].
This commit adds interrupt 'type' cell to the GIC device tree binding
and changes the 'irq' cell to use interrupt type-specific index, rather
than a linear IRQ number.
The 'type'+'irq (index)' combo is automatically fixed up into a linear
IRQ number by the scripts/dts/gen_defines.py script.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly introduced symbol.
Also clean up a header to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The implementation did not account for the incrementing the reference
count past the maximum positive value. Doing so on a signed integer
results in undefined behavior. Switch to an unsigned integer where
such an increment results in a zero count, and add an assert that this
has not happened.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
When items were removed from the list there was not lock which may
lead to race condition and list corruption. Extracted list handling
into external function.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
If clock started immediately after requesting then request was
not yet placed in the list and user callback was not called.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some of defines are present in several header files.
Those defines are the same with value but with different naming.
Common defines are brought to usb_common.h
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Upper layers like OpenThread expect the radio driver to forward ACK
frame received by the radio.
Simulate this behavior on kw41z by recreating the ACK frame from the
available data.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nRF5 driver did not utilize `ieee802154_radio_handle_ack` API, therefore
did not provide ACK frames to the upper layer. This commit fixes this
problem.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add support for the built-in Programmable Interrupt Controller
found in the SweRV EH1 RISC-V CPU
Signed-off-by: Olof Kindgren <olof.kindgren@gmail.com>
Extended flash simulator for posix architecture to read/write data
from a binary file on the host file system.
Further enable the flash simulator by default on native_posix(_64)
boards and updated the documentation accordingly.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
The counter driver tests have been updated so the driver needs
to be updated too.
() Test expects a free running counter.
() Test expects any alarms cannot be set beyond the top value.
() Also, the counter only triggers interrupts when counter reaches
zero (as configured as counting down), it can be do relative
alarms. So return -ENOTSUP when absolute alarms are requested.
() The test expects the callback to be removed once alarm is
triggered. Implement this too.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
