This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds:
1. pin definitions for SPI1 on PE12-15 on STM32L4 devices
2. SPI3 on PA15_SPI3_NSS
Signed-off-by: Armando Visconti <armando.visconti@st.com>
* add pinmux driver. hsdk board has arduino, mikrobus and
pmod interfaces, which can be confiured for different function,
such as: gpio, spi, uart, iic.
* add introduction for arduino, mikrobus and pmod interfaces.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
To work efficiently, SPI_NSS pins require pull-up configuration.
Fix this for whole STM32 series.
Fixes#17998
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fixes#16739. Changed the STM32's SPI MISO/MOSI configurations in order
to reduce the power consumption by approximately 20uA per pin.
According to STM32's Application Notes on GPIO configuration for
low-power consumption, the input pins should be configured with internal
pull-up or pull-down resistor. If a pin is configured as a floating
input, and there is no signal present, the Schmitt trigger randomly
toggles between the logical levels induced by the external noise, thus
increasing the consumption.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
pinmux: Add the relevant definition of the spi3 pin
dts: Fix a bug, spi3 does not have a label
soc: Supplement spi3 related definition
Signed-off-by: Findlay Feng <i@fengch.me>
The i2c5 instance are used on arduino connector of
stm32mp157c-dk2.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@linaro.org>
Add eSPI Microchip XEC driver
Include support for peripheral & virtual wires (channel 0-1)
OOB and flash support can be added in the future
Fix compilation error in pinmux driver
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This driver introduces pinmux configuration capabilities
using zephyr apis for XEC SOCs.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This commit adds pinmux defines for all the external ADC lines
supported by stm32. All defines are named after the datasheet of the
corresponding product lines.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds Atmel SAMR21 soc which is based on SAMD21, but with a AT86RF233
radio connected internally via SPI.
The AT86RF233 is not yet supprted by Zephyr at this point.
This code is very much copy & paste from atmel_sam0/samd21
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Since STM32_OSPEEDR_VERY_HIGH_SPEED flag is required for all I2S_CK
pins, lets add this to the STM32F4 pinmux header and remove the
duplicates in board files. While we are at it, let's add the missing
pinmux definitions for I2S_2 also.
Fixes: #9028
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>