To allow NRF drivers to include nrfx HAL or drivers headers
like with the real HAL, include the top nrfx/ folder
just as the real nrfx does.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
x-nucleo-iks01a3 shield is an arduino compatible companion board
which can be used on top of Nucleo standard boards. It extend
the Nucleo functionalities adding following MEMS sensor support:
- LSM6DSO accel and gyro
- LIS2MDL magnetometer
- LIS2DW12 accel
- LPS22HH pressure
- HTS221 humidity
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds support for the STM32 nucleo_g071rb board
from STMicroelectronics.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com>
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove unnecessary MCU slow down to 16Mhz when using BLE chip BlueNRG-MS
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Provide doc for stm32h747i_disco.
Includes basic description for building and flashing
individual cores.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ARC timer is a MHz-scale cycle counter and works very well with
the new 10 kHz default tick rate. Remove the settings for ARC
hardware.
Note that the nsim board definitions are left at 100 Hz. That is a
software emulation environment that (like qemu) exposes the host clock
as "real" time and thus is subject to clock jitter due to host
scheduling.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These all have what appears to be a promiscuously cut-and-pasted
declaration for a 1000 Hz tick rate. They are all SysTick boards and
will work very well with the new 10 kHz default, so use that instead.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The AN521 is a Soft Macro Model implementation of the SSE-200 subsystem
with SIE-200 and CMSDK components targeting the MPS2+ board. The
SSE-200 subsystem implements two Cortex-M33 cores.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
We use the following commands to rename any
SW._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_SW._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l SW._GPIO_CONTROLLER | xargs sed -i 's/SW\(.\)_GPIO_CONTROLLER/DT_ALIAS_SW\1_GPIOS_CONTROLLER/g'
git grep -l SW._GPIO_PIN | xargs sed -i 's/SW\(.\)_GPIO_PIN/DT_ALIAS_SW\1_GPIOS_PIN/g'
git grep -l SW._GPIO_FLAGS | xargs sed -i 's/SW\(.\)_GPIO_FLAGS/DT_ALIAS_SW\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pwm.h to drivers/pwm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move tracing.h to debug/tracing.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds the necessary bits to utilize the x86_64 toolchain
built by sdk-ng for x86_64 when toolchain variant is either
zephyr or xtools. This allows decoupling the builds from
the host toolchain.
Newlib is also available with this toolchain so remove
the Kconfig restriction on CONFIG_NEWLIB_LIBC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The libc hooks for Newlib requires CONFIG_SRAM_SIZE and
the symbol "_end" at the end of memory. This is in preparation
for enabling Newlib for x86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is the "flagship" platform for the new local APIC timer driver.
The opportunity is taken clean up the configuration as well, so the
choice of local APIC vs HPET timer requires changing only one Kconfig.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The path was changed during generating Ninja-based build system,
so the path of link script file was wrong when testing the
cross-compiler. Fix it by giving the absolute path for link script.
Signed-off-by: Howard Liu <howardliu7874@hotmail.com>
Add board support for 96Boards Avenger96 board from Arrow Electronics
based on STM32MP157A MPU from ST Microelectronics. This board is one
of the consumer editions boards of the 96Boards family following the
Extented CE form factor. More information about this board can be found
in 96Boards website: https://www.96boards.org/product/avenger96/
By default Zephyr console output is available via RAM console, but it
can also be changed to UART7 exposed as UART0 on 40 pin LS header.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use Device Tree,and in particular a new 'bt-c2h-uart' to select which
UART is being used to communicate with an external BLE Host when acting
as a Controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for two CAN bus controller instances and disable both of
them by default. Enable CAN_1 for the STM boards currently supporting
CAN.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The defines in board.h aren't used/buildable so lets remove it. If
someone wants to support the button/led samples they can add DTS support
for those items.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The zephyr-file role creates a link to the GitHub copy of a file. Some
files have been moved so update the file references in the documentation
(found by scanning for uses of :zephyr-file:)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Fix misspellings and doc issues missed during regular reviews (including
some files without a trailing newline)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
