This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bug in the jlink application made it impossible to use OpenSDA
firmware with the mimxrt1052 device name, so we used the generic
Cortex-M7 device name as a workaround. This bug was fixed in jlink
V6.32h (2018-07-05), so now we can use the more specific device name.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface for the nRF52840-DK board (nrf52840_pca10056).
They include the following settings when MODEM_WNCM14A2A is selected:
- UARTE1 pin setup
- DTS / DTS fixup additions for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface instead of ethernet.
They include the following settings when MODEM_WNCM14A2A is selected:
- UART 2 setup
- Avoid ETH_0 setup due to pin conflicts
- DTS addition for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
This enables the cc3220sf_launchxl to automatically
reconnect to the last good known access point (AP).
This method avoids the need to:
- perform a wifi scan for access points on bootup (saving power);
- include hard-coded SSID/passwords in the wifi application.
- include the wifi shell in the wifi application.
- rely on more complex provisioning methods;
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Enable the support for the 3 I2C buses of the STM32F723E-DISCO board,
connected respectively to the WM8994, the Arduino V3/STMOD+ and the
touch panel.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Due to bug #9054 this boards is being disable from sanitycheck
temporarily.
Revert when the board is fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
After running some tests which enable assert macro I found some issues
with the i.MX UART configuration.
This patch configures the Tx Fifo Watermark and Modem Mode accordingly.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Addition of a Flash partition to the 'frdm_k64f.dts' file in the
currently existing 'Application Area' (Partition Location: 0x0001e000
Partition Size:0x00002000). This partitioned area can be used as a FCB
for Bluetooth and other applications.
Signed-off-by: Arjun Warty <arjun.warty@nxp.com>
This commit enables the use of UARTE on Nordic nrf52810_pca10040
development kit. It also instruct console to use UARTE (instead
of RTT).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The Adafruit Feather nRF52 is based on an Nordic Semidconductor nRF52832
based development board with UART, SPI, LED and onboard lithium polymer
battery charger.
Signed-off-by: Florian Gärtner <florian.gaertner@ledcity.ch>
The EFR32 Flex Gecko Wireless Starter Kit contains sensors and
peripherals demonstarting the usage of the EFR32FG1P SoC
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Add first set of boards which can be built with xtools, this will
include all boards at some point, so we might need a better way to
whitelist toolchains that does not include changing every single board
definition file. For now enabling those needed for testing the new
toolchain.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds basic support and for the STM32F769I-DISCO board
with GPIO, USART support. Two USARTs are enabled.The GPIOs are
configured for the 4 LEDs and one button on the board.
Signed-off-by: Yong Jin <jinyong.iot@foxmail.com>
Set HAS_ARDUINO_XXX flag to state boards is compatible with this
connector. It will enable use of shields that requires these flags.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Have qemu_cortex_m3 use the traditional multiqueue scheduler by
default, to be sure it gets test coverage.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This patch adds basic support and documentation for the STM32F723E-DISCO
board, with GPIO, USART, I2C and USB support. Two USARTs are enabled,
the VCP one for the console and the Arduino one. The GPIOs are
configured for the 3 LEDs and the button available on the board.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Unconditional CONFIG_BT_SPI_BLUENRG flag activation was generating
a systematic warning.
Move it in Kconfig.defconfig file to avoid the warning
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ArgonKey board has 12 leds controlled by TI LP3943 led
controller. Add the support in the BSP.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Since the PCA10040 contains the required DC/DC circuitry, enable it by
default while keeping it configurable. This reduces power consumption
during radio activity.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the PCA10040 contains the required DC/DC circuitry, enable it by
default while keeping it configurable. This reduces power consumption
during radio activity.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adding new implementation of logging subsystem. New features
includes: support for multiple backends, improving performance
by deferring log processing to the known context, adding
timestamps and logs filtering options (compile time, runtime,
module level, instance level). Console backend added as the
example backend.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The patch contains basic code support, documentation, dts
file and openocd configuration for STM32F746G discovery board.
This patch related to the issue #6982.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that for any of the removed properties though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Segger provide a firmware makes the ST-LINK on-board compatible with
J-Link OB, allowing users to take advantage of most J-Link features
such as RTT(Real Time Transfer).
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds Bluetooth controller support
for it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit selects HAS_DTS_I2C in bbc_microbit board definition.
It fixes issues similar to issue #8511 for bbc_microbit board
Signed-off-by: Mandar Chandrakant Thorat <mandar.chandrakant.thorat@intel.com>
