This commit adds a sample application using OpenAMP for remote procedure
calls on the LPCXpresso54114. It is adapted from the RPMsg-Lite sample
application added in PR #5960, and uses the IPM driver to provide
interprocessor interrupts.
Signed-off-by: Kristian Klomsten Skordal <kristian.skordal@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current method of setting the openocd runner arguments works for
direct invocation from the command line, but the values that are
written to the CMake cache are not properly separated and are
difficult to parse, due to the fact that in several cases, option
values contain spaces.
Adjust these runner arguments so that the options and their values are
separate list items. This makes it possible to parse them accurately
from the CMake cache.
No functional changes.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add MCUX IPM sample application. It can be run on lpcxpresso54114
board at the moment.
We first build the slave core image out of the remote/ dir than the
primary core image is build which includes the slave core image.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add a board port to allow creation of "firmware" code that will run on
the slave core (Cortex-M0+).
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates documentation for the frdm_k64f, hexiwear_k64, and usb_kw24d512
boards to reflect that they now support a watchdog driver. Updates the
board yamls similarly for sanitycheck.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the configuration, driver, and HAL changes required
to implement a MCUX based RTC driver for the NXP Kinetis KW41Z.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Kconfig keyword GPIO_AS_PINRESET is common for whole nrf52 series.
This patch move it to the series Kconfig.soc file.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add use-prop-name to disconnect-gpios property in st,stm32-usb
yaml, in order to generate friendly name for the definitions.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
In order to run the Simple Management Protocol (SMP) over UART, a DTS
symbol named uart-mcumgr needs to be defined on the board. Enable this
for all Nordic Development Kits.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As part of the prep to support the M0+ core on lpcxpresso54114, we
rename the lpcxpresso54114 board port to lpcxpresso54114_m4 to be
explicit.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename various SoC related defines and files from just being LPC54114
to LPC54114_M4. This is in prep for supporting a build for the second
core on the LPC54114 (the Cortex-M0+).
* Renamed Kconfig SOC_LPC54114 to SOC_LPC54114_M4
* Renamed Kconfig.defconfig.lpc54114 to Kconfig.defconfig.lpc54114_m4
* Introduced nxp_lpc54xxx_m4.dtsi based on nxp_lpc54xxx.dtsi
* Moved some pinmux related defines into SoC code.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT to generate defines for irq and reset gpios in bluetooth
controller node.
Define a bt alias to allow generation of defines with friendly
names.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the frdm_kw41z board to mux spi signals on pins PTC16-19.
Updates the board document to reflect that spi is supported on these
pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxos8700 interrupt pins to all boards that
have this sensor. The frdm_k64f and hexiwear_k64 connect both sensor
interrupt pins to the mcu, but the frdm_kw41z connects only one.
The fxos8700 driver is currently only aware of one sensor interrupt pin,
therefore the routing of INT1 or INT2 to the driver is handled in each
board's dts.fixup.
The fxos8700 sample application has been broken since the refactoring of
the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add cs, irq and reset gpios description in spbtle controller
node and use generated defines instead of Kconfig symbols.
Define a bt alias to allow generation of defines with friendly
names.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Indexed defines were systematically generated even when there
was only one element to generate.
So we ended up generated a lot of _0 defines.
Then we needed to generate aliases to these _0 indexed defines,
in order to get useful defines.
For instance:
#define GPIO_LEDS_0_GPIO_FLAGS_0 4
#define GPIO_LEDS_0_GPIO_PIN_0 5
#define GPIO_LEDS_0_GPIO_FLAGS GPIO_LEDS_0_GPIO_FLAGS_0
#define GPIO_LEDS_0_GPIO_PIN GPIO_LEDS_0_GPIO_PIN_0
This commit allows to generate _0 indexed define only if a
property has more than one elements to define.
Aliases generation to _0 indexed defines are also removed.
Note: IRQ are left untouched since this is frequent to handle
multiple IRQs in a driver
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The disco_l475_iot1 board uses the vl53l0x sensor in XSHUT pin
master control configuration mode. So, it has to explicitly
enable it now.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adds a board-level config option to select whether the code gets linked
into internal instruction tightly coupled memory (ITCM), external
hyperflash, or external qspi flash. The default is ITCM.
Note that we are not yet building an image vector table (IVT) into the
image, therefore the zephyr binary is not bootable by the SoC ROM as-is.
However, the DAPLink firmware prepends an IVT to the image when you use
its drag-and-drop feature to program flash, and this results in a
bootable zephyr application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds flexspi and semc memory controllers to the i.MX RT SoC. Adds
hyperflash, qspi, and sdram external memories to the mimxrt1050_evk
board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Previously, when !CONFI_XIP, BOOTLOADER_SRAM_SIZE was defaulted
to 16 (K), reducing the size of SRAM available for the program.
Also, though it has no effect, the value for SRAM start in the
dtsi file was incorrect.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The frdm_k64f board document incorrectly listed spi signals on PTCD
pins, which don't exist. They should be on PTD pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds DT description of generic storage flash
partition. This fixes issue #7227.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
FS_FLASH_MAP_STORAGE keyword enables the storage partition,
but it was depend on flash_map module which is unused by
NFFS. This patch makes it independent thanks
to it is possible to enable the storage partition
without flash_map module.
FS_FLASH_MAP_STORAGE was renamed to
CONFIG_FS_FLASH_STORAGE_PARTITION
as it is independent for flash_map.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Following changes are necessary to use LP3943 LED driver present
in 96Boards Neonkey board
1. Enable I2C_3 interface
2. Reduce the speed of I2C_3 bus on 96Boards Neonkey. Due to some
design quirks, on board LP3943 LED driver connected to I2C_3
operates only at Standard speed of 100KHz.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
