Add a link to the reel board product page at PHYTEC to help people in
locating schematics, etc.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
The Adafruit Feather nRF52 does not have any RTS/CTS signal
connections between the nRF52832 and the on-board CP2104 USB/UART
bridge. Pins 5 and 7 are regular GPIOs.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This enables I2C, SPI, PWM, RTC and USB.
RTC tested on samples/drivers/rtc
USB tested on samples/subsys/usb/cdc_acm
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add support for ST Micro Nucleo-64 board with the STM32F302R8
processor. nucleo_f429zi and nucleo_f334r8 were used as
references.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Introduces the location property and adds the ability to use values
generated by the device tree configuration.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The config file sourced in openocd.cfg is the nuclean_f3 one instead of the one for
the stm32373c.
This makes it impossible to flash the stm32373c evaluation board rev.B:
Error: open failed
in procedure 'init'
in procedure 'ocd_bouncer'
error: command exited with status 1:
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/bin/openocd -s
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/share/openocd/scripts
-f
/home/maudat/repo_upstream/zephyr/boards/arm/stm32373c_eval/support/openocd.cfg
-c init -c targets -c 'reset halt' -c 'flash write_image erase
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset halt' -c 'verify_image
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset run' -c shutdown
Replace the file sourced by stm32f3discovery.cfg to flash successfully.
Signed-off-by: Mathieu Audat <mathieu.audat@savoirfairelinux.com>
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Add sample application for LSM303DLHC, ST MEMS
system-in-package featuring a 3D digital linear
acceleration sensor and a 3D digital magnetic
sensor.
Enable sample to build on stm32f3_disco board
during sanitycheck.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable LSM303DLHC, ST MEMS system-in-package featuring
a 3D digital linear acceleration sensor and a 3D digital
magnetic sensor, on stm32f3_disco board.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Sync peripheral mapping documentation with the Nucleo F429ZI board doc
and add missing information about Ethernet and the button.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Previously, wifi-enabled samples were not built by sanitycheck for the
cc3220sf_launchxl.
This patch gets the sockets echo sample to build.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The USART fixup in the board dir really are SoC level fixup's. So move
them there and remove the board fixup file since there isn't anything in
it now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The EFM32 Happy Gecko USB-enabled kit contains sensors and
peripherals demonstrating some of the EFM32HG MCU capabilities.
This patch add basic support for this board.
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert over SiLabs based boards to use device tree instead of board.h
to describe buttons & LEDs. There are a few boards that the button
gpio flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Nitrogen board.
Following changes are done:
- Enable I2C0 and SPI0 in board dts
- Add exposed peripherals in board Kconfig
- Update board yaml
- Remove config option to select board
- Update documentation for UART, I2C and SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Carbon board.
Following changes are done:
- Enable exposed I2C2 in dts
- Only enable basic peripherals in board defconfig
- Add exposed peripherals in board Kconfig
- Update documentation for SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Convert over NRF based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit de78ecd "arm: beetle: Use device tree for IRQs" introduces
a regression related to UART1 IRQ.
On arm beetle the UART1 has IRQ number 2.
This patch restores the functionality modifying the arm beetle device
tree file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Some of the headers referenced in the pinmux.c file don't exist. Match
the includes that the lpcxpresso54114_m4 pinmux.c file uses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
