The ip_k66f board (embOS/IP switch) from Segger doesn't have the serial
console pins connected to J-Link OB. As a result one needs to use RTT
to get the serial console.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The documentation page in Zephyr states that the STM32L072CZ has 20KiB
of EEPROM. This is incorrect, the datasheet (and DTS) indicates that
it has 6KiB of EEPROM.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The STM32L072CZ has an EEPROM for user configuration. Enable this for
the B-L072Z-LRWAN1 Discovery kit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This patch enables the rtc so that the testcase
tests/drivers/counter/counter_basic_api
can run on this nucleo_stm32f207 board
also when running sanity check
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The "gccarmemb" toolchain type has been renamed to "gnuarmemb" to
better reflect the official naming.
This commit replaces all references to the "gccarmemb" toolchain type
to "gnuarmemb".
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Removed flow control configuration from Kconfig and updated samples
to use device tree for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The Adafruit ItsyBitsy M4 express is a small (36 mm x 18 mm) ARM
development board with an onboard RGB LED, USB port, 2 MiB of SPI
flash, and range of I/O broken out onto 23 GPIO pins.
Signed-off-by: Michael Hope <mlhx@google.com>
emsdp_em7d_esp is a board with secure just like em_starterkit_em7d,
but the secure feature not configed in defconfig file. we need to add
below configs in emsdp_em7d_esp_defconfig files:
CONFIG_ARC_HAS_SECURE=y
CONFIG_TRUSTED_EXECUTION_SECURE=y
when secure feature enabled, we use secure timer for system tick, so
we need to add below macro for secure timer:
#define IRQ_SEC_TIMER0 20
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
In order for the application to be flashed beginning at address 0,
which is desired when flashing with an external probe,
BOARD_HAS_NRF5_BOOTLOADER must be set to n.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
This follows the board porting guide. Only the the board
efm32hg_slstk3400a does not include a SoC containting an MPU.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Now when we're finally ready to open QEMU port for ARC
we introduce the first ever platform it supports and in fact does
that quite well - Zephyr RTOS.
For now we only offer support of basic EM & HS code execution,
built-in timers, interrupt controller and set of very simple
peripherals: DW UART & optionally MMIO Virtio devices.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We only need a 'compatible' entry for the DK,
not the SoC and part-number. This commit fixes
this and aligns the nRF5340 PDK DTS with the
remainder of nRF-based boards.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Conditionalizes csi pinmuxes on CONFIG_VIDEO for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes display pinmuxes on CONFIG_DISPLAY for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes dac pinmuxes on CONFIG_DAC for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes can pinmuxes on CONFIG_CAN for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes ethernet pinmuxes on CONFIG_NET_L2_ETHERNET for all nxp
boards (kinetis, lpc, and imx families) to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes pwm pinmuxes on CONFIG_PWM for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes adc pinmuxes on CONFIG_ADC for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes spi pinmuxes on CONFIG_SPI for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Pins p0.02/p0.03 that were assigned to the i2c1 node are NFC pins.
Use p1.02/p1.03 instead, which are routed to the standard I2C location
in the Arduino header.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Conditionalizes pinmuxes on associated driver configs (CONFIG_SERIAL,
CONFIG_I2C, etc.) for the rv32m1_vega board to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
I2C1 used LED pins rather than the ones in the Arduino header
position. SPI2 used Arduino D0 for both SCK and MOSI; replace all
pins with D11-D13 which are the standard location for SPI on the
Arduino header.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Enables the adc instance and pinmux associated with arduino header pin
A2 on the frdm_k82 board. Adds adc to the board yaml to ensure we build
adc samples/tests for this board in CI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
As a slow FPGA platform with max. freq < 25 Mhz,
the default CON_SYS_CLOCK_TICKS_PER_SEC=10000 is
not suitable. CON_SYS_CLOCK_TICKS_PER_SEC=100 is
a better value.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Map Arduino interface to LPCXpresso55S69 pins.
Also tell which SPI interface is used by Arduino.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Map mikroBUS interface to LPCXpresso55S69 pins.
Also tell which SPI interface is used by mikroBUS.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Adds support for a new SHIELD, Eth Click.
Mikro-BUS type shield supported in Zephyr.
Adds Kconfig for mikroe_eth_click shield.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_DISK_ACCESS_STM32_SDMMC flag to for each SDMMC pinmux
configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2S flag to for each i2s pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_CAN flag to for each can pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_DAC flag to for each dac pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_ADC flag to for each adc pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_PWM flag to for each pwm pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2C flag to for each i2c pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SPI flag to for each spi pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
