Add support for C-M4 core on STM32H7 series.
It is enabled in Dual core context with 2 alternatives boot methods:
* Boot CM4 CM7: Both core boot at reset, then CM4 enters Stop mode.
CM7 performs system configuration then finally wakes up CM4
* Boot CM7, CM4 Gated: Only CM7 boots at reset. Once done with
system configuration it triggers (requires option byte update)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide basic clock control driver for STM32H7.
Bus clock activation is done through CM7 and CM4 common registers
so we don't have to care to the CPU Id before accessing.
Accesses are not protected for now. Only possible configuration
is system clock source set to HSE driven PLL.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
As with the STM32 boards, these had an existing default for tick rate
that is now lower than the 10 kHz default. They're SysTick devices
that can handle the higher rate just fine. Use that.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The nRF timer runs at only 32 kHz, so there's little reason to try to
divide it to get a synthesized tick rate. Just use the raw clock as
the tick rate, which provides maximal precision and very
singnificantly simplifies the generated code for the ISR.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
UART related defines in STM32F7 files where filled with
references to USART.
Instances 4, 5, 7 and 8 of SoC serial port are actually UARTs.
So rename define's accordingly. Otherwise it couldn't build.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The IPC peripheral is missing from the list of
supported HW for nRF9160, so this commit adds
that.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The AN521 is a Soft Macro Model implementation of the SSE-200 subsystem
with SIE-200 and CMSDK components targeting the MPS2+ board. The
SSE-200 subsystem implements two Cortex-M33 cores.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/slist.h to sys/slist.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move power.h to power/power.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable the MCUX SCG clock controller driver by default for the NXP
Kinetis KE1xF SoC series. Move the generic CLKOUT configuration from
SoC to the clock controller driver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Definition of obsolete FLASH_PAGE_SIZE Kconfig symbol was
remaining in STM32F3 soc files.
Clean these.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
stm32mp1 was adding a STM32 specific Core selection Kconfig
symbol while zephyr generic CPU_CORTEX_M4 could be used for the
same purpose.
Remove STM32 specific symbol and use generic one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sample was not compiling for nordic boards because RTC_0
instance was not enabled by default and RTC_0 device is using
different DT define.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
These events aren't errors at all, but rather part of normal operation.
They shouldn't trigger error messages, especially given that the console
gets absolutely flooded with them if power management is activated.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32WB HCI driver requires definition of 2 RAM regions to support
use of 3 shared memory sections: MAPPING_TABLE, MB_MEM1 and MB_MEM2.
In linker.ld, under conditions of HCI driver to be enabled,
define SRAM1 and SRAM2 based on input defined in stm32wb linker.
Then define the 3 sections MAPPING_TABLE, MB_MEM1 and MB_MEM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several customer configuration (CCFG) settings are useful for
development and deployment. This commit adds support for setting CCFG
values via Kconfig. It follows TI's recommendation of setting CCFG
values and then including the TI provided CCFG. This commit includes
support for enabling the ROM bootloader and additional settings can be
added as needed.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
