SYSCLK_DEFAULT_IOSC_HZ and BUSCLK_DEFAULT_IOSC_HZ are
not used anywhere in the tree and can be removed
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
New power states have more granularity than deep sleep and sleep
states. Just get rid of this and keep the same behavior for now.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Maximum GIC SPI is 228, so maximum INTID is 228 + 32 = 260.
So, _sw_isr_table needs to support 260 entries
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Update register addresses and NVIC/GIC interrupt numbers
according to the latest viper RTL version.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
There is no strict reason to use assembly for the reset routine. Move as
much code as possible to C code using the proper helpers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The name for registers and bit-field in the cpu.h file is incoherent and
messy. Refactor the whole file using the proper suffixes for bits,
shifts and masks.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Enable the driver for the Kinetis Digital-to-Analog (DAC) modules
present in the NXP Kinetis K2x SoC series.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Add some helper macros that will be convenient to use from device
drivers for accessing and error checking pin mux information in the
devicetree:
- NRF_DT_PSEL(): get a PSEL value out of the DT from either a
'foo-pin' or a 'foo-gpios' style property.
- NRF_DT_PSEL_CHECK_NOT_BOTH(), NRF_DT_PSEL_CHECK_EXACTLY_ONE():
helpers for checking that a given devicetree is OK according to
different criteria for setting PSEL properties (NAND or XOR on
whether the properties exist, respectively).
See comments in the patch for more details.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add the declaration and check of debug interface register.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: Ib8ecd53f1d6139613f39243aee83bdd75a30f5be
In NPCX7 series, it contains two tachometer (TACH) modules that contains
two Independent timers (counter 1 and 2). They are used to capture a
counter value when an event is detected via the external pads (TA or
TB).
The CL also includes:
— Add npcx tachometer device tree declarations.
— Zephyr sensor api implementation for tachometer.
— Enable "tach1" device in npcx7m6fb.dts for testing.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Since the uart device clock will be stopped after ec entered sleep or
deep sleep state and restore its clock automatically, there is no need
to implement code for suspending and resuming devices manually.
The driver still needs to check the current status of uart device when
it wants to change its power state to LOW or SUSPEND power state. It is
crucial to forbid ec enters sleep or deep sleep state when uart device
is busy with transmitting data. Or we will observe broken characters on
the uart console.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces power management driver that improves the efficiency
of ec operation by adjusting the chip’s power consumption to the level
of activity required by the application in npcx series.
The following list summarizes the main properties of the various chip
power states. Please refer the power.c file for more detail.
Main power states in npcx series include:
- Active: Core, RAM and modules operate at the clocks generated by PLL.
- Idle: Enter this state when the Core executes WFI or WFE instruction.
- Sleep: clock is stopped for most of modules but PLL is enabled.
- Deep Sleep: As Sleep mode but PLL is disabled.
- Standby: All power rails are turned off besides standby and battery
power rails.
And this CL implements one power state, PM_STATE_SUSPEND_TO_IDLE, with
two sub-states for Zephyr power management system.
Sub-state 0 - "Deep Sleep" mode with “Instant” wake-up if residency
time is greater or equal to 1 ms
Sub-state 1 - "Deep Sleep" mode with "Standard" wake-up if residency
time is greater or equal to 201 ms
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces a kernel device driver implemented by the internal
64/32-bit timers in Nuvoton NPCX series. Via these two kinds of timer,
the driver provides an standard "system clock driver" interface.
It includes:
- A system timer based on an ITIM64 (Internal 64-bit timer) instance,
clocked by APB2 which freq is CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
- Its prescaler is set to 1 and provide the kernel cycles reading
without handling overflow mechanism.
- A event timer based on an ITIM32 (Internal 32-bit timer) instance,
clocked by LCLK which frequency is 32KHz and still activated when ec
entered "idle/deep idle" power state for better power consumption.
- Its prescaler is set to 1 and provide timeout event mechansim.
- Compensate system timer which clock is gating for better power
consumption after ec left"idle/deep idle" power state.
This CL passed starve, timer_api, and timer_monotonic test suites.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
stm32wb and stm32l4 are devices which supports the low power
from the Kernel PM, so is the PM_DEVICE defined.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In case the policy is not available or defined by th application
the pm_policy_low_power_devices is still valid
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The clock configuration is restored by the stm32_clock_control_init
function of the clock_stm32_ll_common driver
when exiting the low power mode
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In case the policy is not available or defined by th application
the pm_policy_low_power_devices is still valid
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The clock configuration is restored by the stm32_clock_control_init
function of the clock_stm32_ll_common driver
when exiting the low power mode.
Keeping the stm32wbxx_ll_utils.h in case the PLL is used for wb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Erratum 19 applies to earlier revisions of nRF5340 DK,
which are no longer supported in the tree, so we can
remove the code that handles it.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add Kconfig options to signify that the nRF5340
HW has support for QDEC instances. Select the
options in the nRF5340 Application core definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This driver missed #32228 PR that converted STM32 drivers
to use DEVICE_DT_GET for clock activation.
Due to the renaming of STM32_CLOCK_CONTROL_NAME to
STM32_CLOCK_CONTROL_NODE, driver could not compile anymore
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove support for the Musca-A board. This board is rarely used, few
are available and superceded by Musca-B and Musca-S.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The NPCX clock driver was already using devicetree, just need to make a
small tweak to use DEVICE_DT_INST_DEFINE and update NPCX_CLK_CTRL_NAME
to match the label for the "nuvoton,npcx-pcc" clock controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add ESPI SAF features to the Microchip eSPI driver as
a separate file. ESPI SAF depends upon the core eSPI
driver adding the ability to attach the system SPI
flash to the EC eSPI endpoint instead of the host
eSPI controller.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
When exiting Stop mode, if system clock is MSI, MSI oscillator is
selected as wakeup from stop clock; otherwise HSI16 oscillator is
selected.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
nxp_k2x.dtsi: Corrects Multipurpose Clock Generator binding
to utilize nxp,kinetis-mcg. Assign MCG to FlexTimer devices.
Enable FlexTimer clocks via System Integration Module clock
gate control registers.
Kconfig.defconfig.mk22f12: Enable default use of
CLOCK_CONTROL_MCUX_MCG when CLOCK_CONTROL is selected.
Signed-off-by: Ryan Holleran <rhollerar@gmail.com>
In this CL, npcx_miwu_interrupt_configure is no longer responsible for
turning the interrupt off. Although the default state of WK_EN is
disabled, the users still have the chance to configure them when WK_EN
is enabled via npcx_miwu_irq_enable(). Hence, this CL also ensures that
WK_EN is disabled before configuring them.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Simplify pm subsystem removing PM_STATE_LOCK option. Constraints API is
small and is a key component of power subsystem.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This activates spi support for this soc. Closes#26428
```tests/drivers/spi/spi_loopback``` succeeded.
Signed-off-by: Bernhard Krämer <bdkrae@gmail.com>
Add support for backup SRAM initialization found in multiple STM32
microcontrollers. Linker script facilities are also provided to make it
easy to define variables in the backup SRAM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This was merged by mistake without being tested and is not working
properly. We need to avoid doing a BUILD_ASSERT() when the relevant
property is missing, because we can't use DT_GPIO_CTLR() on an
undefined property. Handle this with COND_CODE_1().
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
According to https://www.arm.com the correct spelling is now "Arm".
Change the Kconfig input prompts to comply.
Signed-off-by: Detlev Zundel <dzu@member.fsf.org>
This is a trivial patch replacing the spaces at the beginning of the
line with tabs. Otherwise checkpatch will not be happy with any
changes in here.
Signed-off-by: Detlev Zundel <dzu@member.fsf.org>
The STM32F2x was the only one of the STM32 series with a lowercase
input prompt. This looks odd in the SoC selection in 'menuconfig'.
Signed-off-by: Detlev Zundel <dzu@member.fsf.org>
Rather than Kconfig vendor symbols, select stm32 watchdog using
compatible.
So user only has to enable the requested node and set
CONFIG_WATCHDOG=y.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This CL added more additional details for KBC (Keyboard and Mouse
Controller) bus in espi_event structure. It helps the application to
handle different 8042 events in the callback function.
The format of event data for KBC 8042 protocol is:
[23:16] - 8042 event type: 1: Input buf full, 2: Output buf empty.
[15:8] - 8042 data: 8-bit 8042 data.
[0:7] - 8042 protocol type: 0: data type, 1: command type.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The network core doesn't have access to the regulators necessary to
support system power management. That has to be done on the
application core.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This reverts commit f38ba314ea.
nrf5340dk_nrf5340_cpunet doesn't support power management, but that
should be handled another way.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The soft off power state should be supported as it is closest to what
used to be deep sleep state 1, which corresponds to the device off
state supported by hardware.
Fixes#31727.
Signed-off-by: Vincent Wan <vanti.coder@gmail.com>
Based upon discussions with HW designers the 32KHz
programming sequence can be simplified. When FW writes
a value to the VBAT 32KHz Clock Enable register HW checks
if the value is the same as the current value. If the same
the HW does nothing. If different HW begins a sequence to
switch off the current 32KHz source, revert to ring oscillator,
and switch to the new source. FW should program the new value
and then spin until the PCR OSC ID PLL Lock bit goes to 1.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This commit adds minimal support for running zephyr as Xen guest. It
does not use xen PV console, which is somewhat hard to implement, as it
depends on xenbus infrastructure. Instead SBSA-compatible PL011 uart is
used.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Enables the FlexSPI flash driver on the i.MX RT SoC family and
configures the peripheral clocks accordingly. We are careful to only
configure the peripheral clocks if we are not executing in place from
the FlexSPI flash.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a hidden config symbol HAS_MCUX_FLEXSPI selected by NXP SoCs when
the FlexSPI peripheral is present. It will be used as a dependency for a
new FlexSPI flash driver to prevent users from accidentally enabling the
driver on platforms that don't have the necessary hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This targets was previously enabling PM but the code was doing nothing
because the logic was under an unsatisfied ifdef condition.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
