It makes no sense to set the restart condition flag on a first message
and some i2c bus drivers (like the stm32 v1 driver) actually reject
them by returning an error from i2c_transfer().
This patch fixes that by using i2c_burst_read() in tmp112_reg_read()
instead. For consistency, tmp112_reg_write() is also changed to use
i2c_burst_write().
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
I have been using this the TMP112 driver with success with a TMP102
connected to to nucleo-f411re board (via I2C1 using PB8/9).
According to the datasheets, both devices are both driver and pin
compatible although the TMP102 is less accurate.
This temperature sensor is not a thermopile sensor type as stated in
comments.
This patch updates that help info
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Write protection is currently not supported by the mcux flash
driver. This prevents it from working with the DFU subsystem, which
checks the error codes from the write protect routine. Hack it for now
with a semaphore.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Most of sensor channels defined by Zephyr use the main, unscaled
SI unit. We also have SENSOR_CHAN_ALTITUDE which is defined in
meters. So, it only makes sense to define distance in meters too
The only driver supporting SENSOR_CHAN_DISTANCE as of now is
vl53l0x.c, which was updated accordingly. Also, update doc links
in the driver based on the review comment.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This patches fixes a few bugs with the SAM0 driver:
- txrx was trasnmitting too many bytes
- adds support for NULL buffers to the fast paths
- fixes a NULL dereference on the rx buffer slow path
The tests under tests/driver/spi/spi_loopback now pass.
Signed-off-by: Michael Hope <mlhx@google.com>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Add Altera Nios-II QSPI Flash controller driver which has
has 1024 blocks or sectors wich each sector size being 64K bytes.
This driver supports flash erase, write, read and lock operations.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Based on the discussion in #5693, the reason why humidity was defined
in milli-percent was likely following Linux which defines it as such
in its sensor subsystem:
http://elixir.free-electrons.com/linux/latest/source/Documentation/ABI/testing/sysfs-bus-iio#L263
However, Linux defines temperature in milli-degrees either, but
Zephyr uses degrees (similarly for most other quantities). Typical
sensor resolution/precision for humidity is also on the order of 1%.
One of the existing drivers, th02.c, already returned values in
percents, and few apps showed it without conversion and/or units,
leading to confusing output to user like "54500".
So, switching units to percents, and update all the drivers and
sample apps.
For few drivers, there was also optimized conversion arithmetics
to avoid u64_t operations. (There're probably more places to
optimize it, and temperature conversion could use such optimization
too, but that's left for another patch.)
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Now the native console driver also handles stdin
so we can drive the shell from the command line,
a pipe or a file
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Some mcu's have USART_PRESC_PRESCALER defined in the function call. Add
a prescaler of div1 to it.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
The default PWM polarity was 'inversed', which is not aligned with the
other PWM drivers. Unfortunately there is not yet an API to define the
default polarity to be used by the driver, but assume that 'normal'
(signal starts high for the duration of the duty cycle) should be the
default.
Signed-off-by: Ricardo Salveti <ricardo@opensourcefoundries.com>
Uses the new flash erase-block-size dts property to implement the flash
page layout api in the mcux flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
