This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
The PR removes the exclusive limit on enabling both UART_ASYNC_API
and UART_INTERRUPT_DRIVEN so that both options can be enabled
together for same uart driver.
Also, the interrupt handler will be used for both cases. So, enable
definition of interrupt handler for both.
However, nRF UART driver still wants to enable only one of them.
So, a new config is added to disable the code for UART_ASYNC_API
when the option UART_INTERRUPT_DRIVEN is enabled.
Signed-off-by: Jun Li <jun.r.li@intel.com>
Extended the maximum possible number of sections that track statistics
for each flash page.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
IRQ_CONNECT and irq_enable calls in the SiFive UART driver were
misconfigured when the conversion to DeviceTree support occurred.
See also: https://github.com/zephyrproject-rtos/zephyr/pull/10613
Signed-off-by: Sören Tempel <soeren+git@soeren-tempel.net>
This adds support for the async API for SAM0 SERCOM SPI using
DMA to drive the device. This implementation does the reload
for both transmit and receive in the receive DMA handler.
Doing this simplifies the implementation but means that the
transmit drains completely, resulting in the SPI clock pausing
between buffers while both are reloaded in the receive handler.
Tested with tests/drivers/spi/spi_loopback and several simple
programs monitored with a logic analyzer.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
A new function pcie_irq_enable() is added to be used in lieu of
irq_enable() when the target device is PCI(e)-attached. The function
attempts to use MSI, when configured in the kernel and supported by
the endpoint; failing that, it will verify that IRQ requested is in
fact routed to the device by the boot firmware before enabling it.
The NS16550 UART driver is updated to use pcie_irq_enable().
The PCI(e) shell is extended to dump information about wired IRQs.
The up_squared devicetree is fixed (reverted?) to IRQ5 for UART1.
The galileo enables MSI by default.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Add a Kconfig option to enable DMA for SPI with SOC_NRF52832 as long as
it being disabled due to Product Anomaly Notice (PAN) 58 is explicitly
overridden. This allows the SPIM driver to be enabled for the nRF52832
SoC for situations where PAN 58 is not a problem.
Signed-off-by: Andrew Fernandes <andrew@fernandes.org>
Adds Atmel SAMR21 soc which is based on SAMD21, but with a AT86RF233
radio connected internally via SPI.
The AT86RF233 is not yet supprted by Zephyr at this point.
This code is very much copy & paste from atmel_sam0/samd21
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
The upipe specific configuration options are selectable unconditionally.
This commit makes them depend on the upipe driver being enabled.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Since STM32_OSPEEDR_VERY_HIGH_SPEED flag is required for all I2S_CK
pins, lets add this to the STM32F4 pinmux header and remove the
duplicates in board files. While we are at it, let's add the missing
pinmux definitions for I2S_2 also.
Fixes: #9028
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This implements three API functions that are required for
tests/subsys/usb/device to build:
- usb_dc_ep_disable()
- usb_dc_ep_halt()
- usb_dc_ep_flush()
While halt and disable are trivial, flush is just a stub for now.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Make sure the parameters for the API functions are valid, return error
otherwise.
This is expected by the tests/subsys/usb/device test case.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Change file naming pattern from BoardNameX_ll_clock.c to
clock_BoardNameX.c
File containing LL functions will have the "_ll_" naming
scheme (such as clock_stm32_ll_common.c and .h)
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This is mainly testing purpose from native_posize ethernet
driver. Enable CONFIG_ETH_NATIVE_POSIX_VLAN_TAG_STRIP to have
VLAN tag strip feature on ethernet Rx frames.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We shall not enable by default a system timer in ARM
platforms, namely the SysTick, the Nordic, or the SAM0
RTC timer, simply by assessing the hardware capabilities
(e.g. by conditioning on CPU_CORTEX_M_HAS_SYSTICK).
Instead, now, all ARM platforms needs to explicitly set
their system timer module. Note that this has already
been the case for ca 80% of the ARM platforms.
This clean-up allows us to decouple HW capabilities from
system configuration (for example, Nordic platforms may
enable option CPU_CORTEX_M_HAS_SYSTICK, and still use
the platform-specific RTC timer for system timing).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit renames the symbol CPU_HAS_SYSTICK to
CPU_CORTEX_M_HAS_SYSTICK, to look similar to all
other CPU_CORTEX_M_HAS_ options, and moves the
K-config symbol definition from arm/core/Kconfig to
arm/core/cortex_m/Kconfig.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
For example it should be possible to compile and use the SLIP module
with NET_L2_DUMMY. This required the following changes:
* Fix a typo in the initializer for struct dummy_api
* Only define eth_capabilities if CONFIG_NET_L2_ETHERNET is defined to
silence a -Wunused-function compiler warning
* Unconditionally include net/dummy.h
Signed-off-by: Sören Tempel <soeren+git@soeren-tempel.net>
Without this change compilation of the SLIP module would fail if LLDP
wasn't enabled. There is also no need to include net/lldp.h explicitly
as net/ethernet.h will include it conditionally if CONFIG_NET_LLDP is
defined.
Signed-off-by: Sören Tempel <soeren+git@soeren-tempel.net>
Enabling the RTC event is intended to support peripheral-to-peripheral
interconnects, so introduces a request for HFCLK and PCLK16M when the
event is triggered. This specific event is never used with PPI so
enabling events apparently does nothing but increase power consumption.
Closes#15513
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Statistic for flash has limitation regards number of pages possible to
be counted. This path introduces check for that in source file as it is
not possible to preserve the limit in Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When there is no need to divide the PWM clock (i.e. the requested
period cycles fit the 15-bit PWM counter), the prescaler value
should be 0, not 1.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The GPIO driver for the Intel Apollo Lake has so many pins it has to
export ten devices to shoehorn its one device into the GPIO API. The
current implementation uses the shared IRQ driver because these
pseudodevices all share one IRQ. However, since the GPIO driver is
aware of all the possible interrupt sources, it's smaller and faster
(and not even messy) to handle it internally, so this patch eliminates
the dependency on the shared IRQ driver.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Provide access functions for manipulating network interface flags.
There is no need for the caller of this API to know about the inner
details of the flags.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Migrate from "legacy" PCI support (drivers/pci) to new PCI(e) support.
The e1000 driver is merely for testing with QEMU and so should not be
a model for the use of PCI(e) functions. Consult instead "real-world"
PCI(e) drivers like the NS16550 UART (drivers/serial/uart_ns16550.c).
Signed-off-by: Charles Youse <charles.youse@intel.com>
Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
In order to generalize the currently specialized nRF51 IC setup hook,
make the following changes:
- Generalize the hook to bt_ic_setup()
- Use a weak NOP version by default
- Move the currently existing one to the board folder
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
