Now the native console driver also handles stdin
so we can drive the shell from the command line,
a pipe or a file
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Some mcu's have USART_PRESC_PRESCALER defined in the function call. Add
a prescaler of div1 to it.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
The default PWM polarity was 'inversed', which is not aligned with the
other PWM drivers. Unfortunately there is not yet an API to define the
default polarity to be used by the driver, but assume that 'normal'
(signal starts high for the duration of the duty cycle) should be the
default.
Signed-off-by: Ricardo Salveti <ricardo@opensourcefoundries.com>
Uses the new flash erase-block-size dts property to implement the flash
page layout api in the mcux flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Current buffers might be configured to skip data, thus only len will be
set, buf will be NULL. Buffer should be used if only len is > 0 and
buffer is valid as well.
tx/rx are "on" if len is > 0
tx/rx buf should be touched if only len is > 0 _and_ buf != NULL.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move to new Kconfig pattern in which we use an if !HAS_DTS_I2C_DEVICE
block for the Kconfig symbols that can now come from DT generation.
This pattern is useful to allow us to define default values for the
generated symbols for build-all testing.
Fixes: #5877
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Transfer is an important concept of USB specification.
During a transfer, several packets can be transmitted.
Today the usb API only provides ep_read and ep_write
functions but the transfer concept is missing.
This is typically ok for basic drivers which don't have
to take care of how data is transfered/splitted.
However there are some drivers like CDC EEM, in which
transfer concept is important for packet management.
Moreover, current ep-write and ep_read method have a
different implementation in usb_dc_dw and usb_dc_stm32
device drivers. For example usb_dc_dw supports only
1-data-packet transfers due to its implementation.
This can increase latency and reduce performance.
I think this is something we need to fix/improve by
implementing better transfer management.
This patch introduces usb_dc_ ep_transfer method which
can be used to configure IN/OUT transfers. This allows
to configure and request different transfer sizes and
should prevent usage of the current stm32 temporary
buffer.
This method has asynchronous and synchronous mode.
Synchronous mode waits for transfer completion before
returning. Asynchronouse mode (irq safe) configures
the transfer and returns immediately, the provided
callback will be then called on transfer completion.
This also update ep_write and ep_read stm32 implementation
to use this new method but keep their behavior unchanged
for legacy reasons.
Note that for now this method is local to stm32 device
driver, however the goal would be to expose this function
as a new USB device driver API method so that class
drivers use it. This will request same implementation in
the usb_dc_dw_driver.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
usb mass example need usb_dc_ep_read_wait/continue API.
test usb mass storage with RAM DISK on stm32f4 series.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Move to use an if HAS_DTS_I2C_DEVICE instead of depends on so that the
Kconfig sybmols don't even show up if HAS_DTS_I2C_DEVICE is true.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds pinmux defines to use I2C2 at PB10/PB11 for
stm32f0-based boards.
Needed for stm32f072b_disco board to use extension
connector
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
We want to move to use a common FLASH_DEV_NAME across the various flash
drivers. So samples, tests, or other code can be a bit more generic. So
replace CONFIG_SOC_FLASH_NRF5_DEV_NAME with FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove SoCs part dependency of CLOCK_STM32_PLL_PREDIV1 config since
it will only be used on parts having an HSE oscillator, ignored
otherwise.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The shared irq support doesn't really require its own dir, lets merge it
into drivers/interrupt_controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The generic library provided by ST in ext/hal/st/lib/sensor/vl53l0x
needs to be adapted to the platform. In this case, the main
modification is the way to use I2C. This is now using the Zephyr
I2C API.
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Add driver for ST vl53l0x time of flight sensor.
This driver can be used in 2 modes :
* proximity sensor :
configure VL53L0X_PROXIMITY_THRESHOLD
will return 1 if target is between sensor and threshold,
else, 0
* distance sensor :
will return the distance in millimeters from sensor to target
This driver use the official STMicroelectronics library for vl53l0x.
(in ext/hal/st/lib/sensor/vl53l0x)
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Add gpio mcux driver which can be used for lpcxpresso54114 and other lpc
socs. In this driver, CMSIS register access is made for GPIO.
Option for access by GPIO Pin is provided as of now.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add usart-yaml in dts.
Build fsl_lpc_usart and fsl_lpc_flexcomm in
ext/hal/nxp/mcux/drivers/Makefile.
Only polling mode is implemented in usart now. Interrupt can be added in
future.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new pinmux driver for lpcxpresso54114 based on mcux.
Signed-off-by: Shiksha Patel <shiksha.patel@nxp.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use "select USE_STM32_LL_SPI" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_USB/USE_STM32_HAL_PCD/USE_STM32_HAL_PCD_EX"
to select the needed STM32 HAL files, instead of editing
ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_RNG" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_HAL_TIM" to select the needed STM32 HAL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_I2C" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_HAL_ETH" to select the needed STM32 HAL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Use "select USE_STM32_LL_UTILS" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The CMakeLists lost the config for uart_mcux_lpsci.c, which is the
console driver for board frdm_kl25z. So just add "uart_mcux_lpsci.c"
into drivers/serial/CMakeLists.txt to make it work.
Signed-off-by: Jason Wang <jason.yanping.wang@hotmail.com>
In flash driver init, write_block_size could be initialized
with FLASH_WRITE_BLOCK_SIZE which is generated from device
tree parsing (dts property: "write-block-size")
Fixes#5305
If not defined, generate a compilation error.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
