Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree.
We add a property ('calib-offset') for the SAM{D,E}5x family of SoCs
that is the bit position offset from ADC0 BIASCOMP in the NVM Software
Calibration Area Mapping. For ADC0 this is typically 0 and for ADC1
this will be 14.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the missing prefix z_ required to make the ESP32 version override
the weak implementation.
General practice in ESP32 seems to be to use the MAC address, so
extract that in its canonical byte order.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new path access helpers to avoid hard-coding devicetree paths
in Kconfig, which is a bit messy.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove logging of individual threads spread out throughout the
bluetooth subsystem. The stacks can be analysed by enabling the
following options.
CONFIG_THREAD_ANALYZER=y
CONFIG_THREAD_ANALYZER_AUTO=y
CONFIG_THREAD_ANALYZER_RUN_UNLOCKED=y
Optional:
CONFIG_THREAD_NAME=y
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add a Kconfig option that allows user to set any necessary config
using management interface before interface be operational. A use
case is set the EUI-64 address from an external EEPROM by the
NET_REQUEST_IEEE802154_SET_EXT_ADDR command. After all configs
are done net_if_up() can be invoked to bring interface up.
Fixes#23193.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add local-mac-address on DT and enable it on rf2xx driver. If user
define local-mac-address this value will be used as default mac address.
Otherwise driver automatically add a random mac address.
On application level user can change default mac address using net_mgmt
command with NET_REQUEST_IEEE802154_SET_EXT_ADDR parameter defined on
include/net/ieee802154_mgmt.h header.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fasten events handling by unloading callback treatment.
A RX thread is created. IPM RX events are dumped in a FIFO
which is processed in the thread context.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options and dts fixups for GPIO instances.
A side-effect to using DT_INST_FOREACH is that GPIO ports A0 and A3
are now enabled, whereas they were originally disabled by default as
an optimization.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Changing more of DT_* prefixed macros that refer to instances to use
DT_INST macros in GPIO, I2C and UART drivers.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert various DT_DTCM_* macros to use DT_CHOSEN(zephyr_dtcm) and
associated macros from devicetree.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert pinmux driver to use nodelabels to get references to devicetree
nodes using the new devicetree.h macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio driver to use nodelabels to get references to devicetree
nodes using the new devicetree.h macros.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree. Move the prescaler setting
from Kconfig to devicetree as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_L2_SRAM_* to just L2_SRAM_* and set it using new DT macros.
Do something similar for DT_LP_SRAM_* renamed to LP_SRAM_*
Updated the intel_gna driver as it used the DT_L2_SRAM_* defines.
This change also lets us remove dts_fixup.h on intel_s1000 and
intel_apl_adsp SoCs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-spi binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-i2c binding for dma to replace the dma property with
proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked spi_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use NODELABEL macros rather than DT_INST as this driver is so far
limited to support of LPTIM1 instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the driver to use the new dt macros. As part of this change we
remove a bunch of defines that happened in dts_fixup.h that didn't
belong there. Some of these should be converted to devicetree
properties at some point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When notifying the handler that GPIO interrupt has occurred
pass only pins that are associated with this handler.
Fixes: #24634
Signed-off-by: Pawel Dunaj <pawel.dunaj@nordicsemi.no>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Espi bus interrupts need to re-enable after espi reset to get
all espi bus and vw signal interrupts.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
Epsi slave need to respond with an OOB_RST_ACK for OOB_RST_WARN sent by
master during host reset. Enable interrupt for OOB_RST_WARN to receive
signal changes and respond with ACK.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
The check of the SF_TXDATA_FULL flag is only done on the register
address and not on the actual register content.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We also remove
defines in dts_fixup.h as they are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
