Fixes incorrect usage of n instead of _num as the instance identifier
in several lines of the driver initialization macros. This mismatch
caused build errors when multiple I2C instances were enabled, due to
redefinition of the same variable.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
The STM32 video encoder (VENC) peripheral is a hardware
accelerator allowing to compress RGB/YUV frames into
H264 video bitstream chunks.
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Default to using DIRECT_ISR if nothreading. This allows the SW ISR
table to be excluded if nothreading.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
This commit adds eSPI TAF support for npck3, including initialization
settings for flash operation mode. It also updates the mechanism to
release FLASH_NP_FREE, preventing a possible race condition between
automatic and standard requests.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
This commit adds eSPI support for npck3, including support for the
maximum frequency of 66MHz. The method to read the level of eSPI reset
pin differs on npck3, so the definition of eSPI_RST has been updated
accordingly.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit updates the OOB payload size. The maximum payload size in
the OOB chapter represents the protocol payload embedded whithin the
packet. The total size should also include the header length, so the
header length needs to be added when checking the overall size.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
This commit adds support for SLP_LAN and SLP_WLAN virtual wire signals
to notify the system.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit adds new device tree properties and Kconfig options to
distinguish the support in different chip.
Signed-off-by: Tom Chang <CHChang19@nuvoton.com>
Refactor the driver of FT8xx coprocessor by moving code common to
coprocessor commands to common functions.
Signed-off-by: Hubert Miś <hubert.mis@gmail.com>
Allows CONTAINER_OF inside trigger handler to be used to obtain a valid
ptr to the composite struct consisting of a struct sensor_trigger trig.
Fixeszephyrproject-rtos/zephyr#97124
Signed-off-by: Christoph Jans <jans.christoph@gmail.com>
To reduce the number of Kconfig files and improve maintainability,
we are merging the three different Kconfig files from Silabs for ADC.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This commit introduces DMA support for the Silabs IADC driver.
A new Kconfig option is added to enable DMA support, ensuring
compatibility with the existing ADC configuration.
DMA can be used for synch/asynch operation.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
video_shell_get_ctrl_by_name() normalized the search string (`name`)
instead of the control's actual name (`cq->name`). This made the
comparison always succeed on the first control, causing incorrect
lookups at runtime.
Update the code to normalize `cq->name` before comparison so that
each control name is correctly checked against the search string.
Signed-off-by: Khanh Nguyen <khanh.nguyen.wz@bp.renesas.com>
This makes userchan transport behavior similar to other HCI
transports (eg IPC). Improved logging gives clear overview
of what RX events are discarded helping for configuration
tuning.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add missing SoC header include required by memory region assertion
to adc_nrfx_saadc and i2s_nrf_tdm shims.
Signed-off-by: Michał Bainczyk <michal.bainczyk@nordicsemi.no>
Introduce Bouffalo Lab L1C cache management functions
This allows invalidating instructions and data on
BL60x and BL70x
Signed-off-by: Camille BAUD <mail@massdriver.space>
To avoid issues with multiple calls to fetch the USN returning garbage
data, memoize the returned USN value and re-use it on subsequent calls.
Signed-off-by: Pete Johanson <pete.johanson@analog.com>
STM32L5xx series shares several DMA configurations with
the other platforms. These changes aim to enable platform
specific DMA configuration and align them to other platforms.
Signed-off-by: Mario Paja <mariopaja@hotmail.com>
Add Clock Control driver support for Renesas RZ/A3UL, V2L
Signed-off-by: Quang Le <quang.le.eb@bp.renesas.com>
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Fix SDMMC initialization by starting with 1-bit bus mode and
properly configuring wide bus operation after HAL
initialization.
The SDMMC protocol requires initialization to start in
1-bit mode before switching to wider bus widths.
Previously, the driver attempted to initialize directly
with the target bus width, which could cause later read/write
failures.
Changes:
- Initialize with SDMMC_BUS_WIDE_1B instead of target bus width
- Add HAL_SD_ConfigWideBusOperation() call if needed after
successful init
- Add error logging for wide bus configuration failures
Fixes potential SDMMC read/write failures issues on STM32 platforms.
Signed-off-by: Shan Pen <bricle031@gmail.com>
Add support for the UltraChip UC8151D e-paper display (EPD) controller.
The UC8151D is part of the UC81xx family of display controllers commonly
used in e-ink displays.
This implementation extends the existing UC81xx driver infrastructure by
adding device tree bindings, Kconfig options, and the necessary driver
code to support the UC8151D variant.
Signed-off-by: Marc Espuña <mespuna@cactusiot.com>
The millionths value is calculated incorrectly.
The sensor has a precision of 0.5 which is 500000 millionths, but
there is an extra zero in the code. This fix removes the extra zero.
Signed-off-by: Sašo Domadenik <saso.doma@gmail.com>
Handle the case where there are multiple different kinds of UART on one
platform, the other UART driver select SERIAL_SUPPORT_ASYNC but LPUART
did not, causing build error in LPUART driver. Shield LPUART driver from
this case by introducing driver config to indicate that in fact LPUART
is the one enabling ASYNC.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Declare variable at the beginning of the function since having it
declared in the default case makes clang unhappy (can't declare a
variable after a label).
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Fixed a wrong function declare of 'nds_l2_cache_init'.
Replace `SOC_FAMILY_ANDES_V5` with `DT_HAS_ANDESTECH_ANDESCORE_V5_ENABLED`
condition to enable it to be used by compatible MCUs
Signed-off-by: Jacky Lee <jacky.lee@egistec.com>
The DDR LUT entry for ERASE_CHIP was configured with an incorrect
kFLEXSPI_Command, resulting in the erase operation not being executed.
Signed-off-by: Andre Heinemans <andre.heinemans@nxp.com>
The maximum speed should be configured individually for each board
since it depends on the layout and the controller's flexspi capabilities.
Signed-off-by: Andre Heinemans <andre.heinemans@nxp.com>
In the DDR LUT, the dummy cycles were not defined for READ_STATUS_REG
and had a wrong value for READ.
The default amount of dummy cycles on this chip are 20 (0x14).
This means the LUT should contain the value of 0x28 (0x14*2) for DDR
at these entries.
Signed-off-by: Andre Heinemans <andre.heinemans@nxp.com>
The TXFNF needs to be disabled for additional I3C targets
during the DAA process. Otherwise the TX interrupt might be triggered
before receiving full PID for target.
Signed-off-by: Adam BERLINGER <adam.berlinger@st.com>
Make sure the nordic_vpr_launcher gets started after the coresight
driver if that is present.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
Added driver and bindings for the coresight nrf submodule.
add integrated it for the nrf54h20.
The coresight subsystem is a combination of ARM Coresight peripherals
that get configured together to achieve a simplified configuration based
on a desired operating mode.
This also replaces the previous handling in the nrf54h20 soc.c which was
powering the subsystem up but not configuring it.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
Pinctrl needs to set the needed drive and direction of the pins. Also
this later allows automatically setting the clock bit for the traceclk
pin.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
Moved the nrf_etr driver from the drive/misc folder into the recently
established driver/debug folder where it is a better fit. Moved the
associated files such as bindings and headers accordingly as well.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
The general ADC documentation states, that it is possible to use the
adc_read_async function with third parameter (k_poll_signal *async) set to
NULL, in which case the callback is called when all channels have been
converted. This change fixes this issue as it now also checks if a callback
has been set.
Signed-off-by: Torbjørn Biering Tvermosegaard <tbt@foss.dk>
