In sys_clock_set_timeout(), input "ticks" is used to compute next
timeout point, Ambiq's STimer API used to sets next timeout has input
parameter as ui32Delta, which inside the API is using
"this value to add to the STimer counter and load into the comparator
register" according to its spec, thus the this delta clock is
almost equivalent to input "ticks"'s concept, and is not related to
last_count, it should be computed directly from input "ticks".
This correction fixes the test case failure at
zephyr\tests\kernel\tickless\tickless_concept.
Signed-off-by: Bryan Zhu <bzhu@ambiq.com>
Using SDL_DISPLAY_ZOOM_PCT would cause mouse pointer/touch input
to not click at the correct position.
Signed-off-by: Jakob Krantz <mail@jakobkrantz.se>
This change marks each instance of the 'spi_driver_api' as 'static const'.
The rationale is that 'spi_driver_api' is used for declaring internal
module interfaces and is not intended to be modified at runtime.
By using 'static const', we ensure immutability, leading to usage of only
.rodata and a reduction in the .data area.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This change marks each instance of the 'api' as 'static const'.
The rationale is that 'api' is used for declaring internal
module interfaces and is not intended to be modified at runtime.
By using 'static const', we ensure immutability, leading to usage of only
.rodata and a reduction in the .data area.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Cache configured radio channel and apply them only when a relevant
radio task is requested.
This allows to configure the channel in the transmit metadata, thus
avoiding unneeded `nrf_802154` API calls in some scenarios.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Remove `IEEE802154_SELECTIVE_TXPOWER` option.
Cache the tx power value in nRF5 driver and make use of it on each
operation.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Rework the interrupt handlers of the FTM driver to support SoCs on
which FTM channels and overflow are routed through individual
interrupts, as opposed to a single OR'ed interrupt.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Enable runtime mmio configuration in mcux_lpspi driver. The fsl_lpspi
driver relies on physical address to determine instance number.
So mmap flag 'K_MEM_DIRECT_MAP' is required.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Enable runtime mmio configuration in mcux_lpi2c driver. The fsl_lpi2c
driver relies on physical address to determine instance number.
So mmap flag 'K_MEM_DIRECT_MAP' is required.
Signed-off-by: Chekhov Ma <chekhov.ma@nxp.com>
Add return code to lpspi spi_mcux_transfer_next_packet and print the
kStatus_* return code since it information is lost when translated to
errno.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a check to input_kbd_matrix_actual_key_mask_set() to return an error
if trying to change a key mask but the device does not define a keymask
in the first place.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This fix adds the STM32L4P5xx to the list of devices that have an
offset-to-page shift calculation of 12 bits. Previously, the driver
would only shift the offset by 11 bits when calculating the page to
erase.
This would prevent the driver from erasing the correct page.
Signed-off-by: George Beckstein <george.beckstein@ampaworks.com>
Use LL_RTC_EnterInitMode and LL_RTC_DisableInitMode instead
of rtc_stm32_enter_initialization_mode and
rtc_stm32_leave_initialization_mode.
Signed-off-by: Petr Hlineny <development@hlineny.cz>
When device runtime pm is enabled, Backup Domain protection is active
most of the time. RTC driver need this protection to be disabled in
order to set the time or calibration. This fix disable the protection in
set time and set calibration functions.
Fixes: 62843
Signed-off-by: Petr Hlineny <development@hlineny.cz>
There can be a case where not all regulators are being used,
resulting in an unused-const-variable warning,
so let's add a __maybe_unused keyword to suppress it.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
This commit modifies the I2S driver to work for STM32H7
family of MCU's. Currently only TX is working.
Tested on nucleo_stm32h743zi. Requires dma1 & dmamux1 to be enabled.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
Fix issue #66806, caused by PR #65172.
Return -EINVAL from bt_spi_get_header if op is neither SPI_READ nor
SPI_WRITE.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Current implementation of NXP mbox driver mbox_nxp_imx_mu
is using only one channel 0.
This commit adds support for multiple mbox channels as is
indented by mbox drivers.
Change done in .send api signaling mode leveraging provided
channel id to select correct General Purpose Interrupt.
Another change done in IRQHandler to check and handle all
channels.
Signed-off-by: Tomas Galbicka <tomas.galbicka@nxp.com>
The setting of initial state in handled by the common driver,
which calls the enable function for any regulator that has
regulator-boot-on set, and is not already enabled.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
When not using 4 channel capture, overflows were never reported
to the application, because the check was in the
four_channel_capture_support branch.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
Check the return values from the I2C API functions called in init() and
fail driver initialization if unsuccessful.
Fixes: #66827
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The QCCID handler is Quectel specific and as such may not be part
of the modem cellular driver which only supports commands defined
in 3GPP TS 27.007
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
The modem_cellular.c driver now uses a common script to get
signal strenght, which is run on demand. This is more efficient
than polling it, and simpler since every modem doesn't have to
define their own variant of the script.
Additionally, the CSQ handler now stores the "raw" rssi value
returned from AT+CSQ to be parsed by the cellular_modem_get_signal
implementation.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Move the implementations of the cellular API in modem_cellular.c
to an cellular_driver_structure, and implement this API structure
withing the device drivers.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
In Passive Receive mode, ESP modem will buffer rx data.
This fix makes the data still available to user,
even though the peer has closed the socket.
Otherwise, user will fail to get the last rx data,
when the socket is closed by the peer.
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Don't execute `irq_enable` in process of the `ra_icu_irq_connect_dynamic`.
The caller of `ra_icu_irq_connect_dynamic` is only `gpio_ra_pin_configure`
at this time. `gpio_ra_pin_configure` calls `irq_enable` just after called
`ra_icu_irq_connect_dynamic`.
So removing 'irq_enable' from 'ra_icu_irq_connect_dynamic' has no effect
on behavior.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
DEVICE_MMIO_MAP() is an unnecessary process, so delete it.
I created uart_ra.c based on uart_rcar.c, but
I forgot to correct the name. I fixed it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Devices like the ATSAM series chips have retained registers
which are used to store memory. The memory is accessed just
like RAM, but since they are registers, their size and
address is used directly.
This commit adds a near complete copy of the generic retained
ram driver and bindings file, adding the reg property to
the bindings file, and updating the init macro in the driver
to use the reg address and size.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Implement level based gpio interrupts, by using a worker queue to
repeatedly call the gpio callbacks until the gpio is no longer active.
Update unit test for new interrupts.
Bug #66401
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Use #if instead of IS_ENABLED for
CONFIG_SOC_IT8XXX2_GPIO_GROUP_K_L_DEFAULT_PULL_DOWN, otherwise DTS files
are required to provide gpiok and gpiol even if they are not used.
Bug #66401
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Similar to other ITE drivers, wrap register accesses in ECREG. This will
allow mocking out the registers in tests.
Bug #66401
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Erase operation with block of 64KByte
larger size than the default 4K sector size
if the flash supports.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add max size check to dac sam and sam0
There is no size check in dac_sam_write_value and dac_sam0_write_value.
Besides, the ret value should also be different.
Fixes#65021
signed-off-by: Gaetan Perrot <gaetanperrotpro@gmail.com>
Move reading PCIE_CONF_CMDSTAT before actual usage. There are four
return branches before value is used.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add an option to enable a input_kbd_matrix_actual_key_mask_set API to
enable or disable keys dynamically in the mask. This can be useful if
the exact key mask is determined in runtime and the device is using a
single firmware for multiple matrix configurations.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This change marks each instance of the 'rtc_driver_api' as 'static const'.
The rationale is that 'rtc_driver_api' is used for declaring internal
module interfaces and is not intended to be modified at runtime.
By using 'static const', we ensure immutability, leading to usage of only
.rodata and a reduction in the .data area.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Only reset cause is supported as there is no common unique id
present on those chips.
Unique ID can be put in OTP but there is no single specification for this.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Use K_KERNEL_STACK_SIZEOF instead of the config directly to set the
stack size in k_thread_create() calls.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
