Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Now that a hw-flow-control DTS binding has been added for MCUX uart,
let's check for the DT_ define and enable support in the MCUX HAL
layer.
Signed-off-by: Michael Scott <mike@foundries.io>
In case of TX IRQ pending,
uart_stm32_irq_is_pending() function always return 0,
because "is TXE enabled ?" is checked instead of "is TC enabled ?".
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Added new UART API, that allows for longer transmissions, leaves
IRQ handling on driver side and allows for DMA usage.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Remove all references in the documentation and Kconfig options
to the legacy shell to avoid confusing users and developers
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The mcux lpuart shim driver was updated in commit
20202902f2 to use DT_ prefix in all
defined labels not related to Kconfig, but instance 2 was missed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds a serial driver for the ARM PL011 IP block.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
1. optimize the baudrate calulation
2. For arc iot soc, the interval val is 4
3. before write any regs, the clk of uart must be enabled
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
In Kconfig.stm32, all UART port symbols were defined with a dependency
on symbol UART_STM32. This is redundant since they are located under
if UART_STM32 condition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Zephyr gecko drivers depend on libraries provided by the vendor. The
same libraries may also be used directly by the application code or
RAIL library. To facilitate the latter use case scenario this commit
adds Kconfig options to independently enable compilation of vendor
HAL library modules.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implementations of both flavors of serial drivers for Nordic SoCs
are no longer dependent on the gpio driver. Remove the dependency
from Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Check clock_control_on return value now that it is checking appropriate
bus is used in the request.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch fixes the uart isr calling the callback with wrong data
(#11465) and the uart_poll_in checking the wrong status flag.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This effectively reverts part of earlier 49bb163756 which moved
interrupt acknowledgement until after return from the user callback.
This was done confusing the flow of this driver with how some other
drivers do it, where pending interrupt status is checked by
uart_irq_rx_ready()/uart_irq_tx_ready(), which should be called by
the callback. But the uart_cmsdk_apb driver actually uses different
hardware register in these functions. And acking IRQs after user
callback can lead to race condition and losing an IRQ, and the
simple fix in this case is just move acknowledgement to where it
was before.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Calling fifo_fill function from uart_nrfx_uarte in the same
interrupt more than once, would break previous transmission.
Following fix adds checking if previous data was sent, and
if not, returns 0.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This is a follow-up to commit b3ca789ef25627bcf7b02ec2aa7fa900fba37227.
Apparently, another driver needed to be updated but this was not caught
up in CI builds at that time.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The Zephyr console and shell interrupt processing assumes
a TX interrupt is evoked upon first enabling the TX
interrupt via uart_irq_tx_enable.
This was not the case with the cc32xx uart, coming out of
reset, with FIFO's disabled.
The only way found to achieve this behavior is to fill
the fifo with a non-printable character on initialization.
Also, the uart driver was explicitly clearing TX/RX interrupts in
its isr, which was unnecessary, as the act of reading/writing
did that implicitly.
These fixes allow the cc32xx uart to work with the
current Zephyr console/shell design.
Fixes: #11202
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
1. There's an expectations that TX ready (i.e. TX buffer space
available) interrupt is a level interrupt, i.e. always active
while there's TX buffer space available. In particular, there's
an expectation that after uart_irq_tx_enable(), the TX interrupt
will immediately fire (assuming free TX buffer space is available).
But CMSDK UART interrupt appears to be edge interrupt, firing only
on buffer state change. So, after irq_tx_enable(), we need to
"bootstrap" interrupt processing by calling user-defined ISR
manually (the ISR will see that TX ready to accept a new char,
will write it there, then we'll get interrupt once TX buffer is
ready again).
2. Interrupts should be acknowledges only after user ISR is called,
because the ISR will check the status of interrupts.
3. Update stale comments.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update a couple of labels generated from DTS used directly (not through
dts_fixups) in some serial drivers, to the reflect recent changes made
to the extracting script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Provide CONFIG macros for clocks bits and bus properties in fixup
files and use them to simplify logic in uart devices instanciation
code
Fixes#10448
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove the redundant semicolon used as a terminator in
`if`, `switch`, `while` statements.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
If data is received before an IRQ handler was set and enabled,
hardware sets the ORE flag. Once set, the IRQ routine starts
hogging the CPU until ORE is cleared. This change will clear
the flag when user code attempts to drain incoming data.
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
Update the uart_miv driver to get params like name, addr, baud-rate,
clock freq from DTS generated defines. Fixup related board and soc code
as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix misspellings in Kconfig files that show up in the configuration
documentation (and make menuconfig screens).
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
