This patch removes a superfluous write to the INTMAP1 register
that happens because the byte count was previously wrong.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
The measurement time in normal mode was too short.
With this commit the maximum value of the datasheet is applied.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Sensor value computation was creating a 64-bit integer value, passing
that to 'abs' and assigning that to an int32_t result and then sanity
checking the result. If the computation goes badly wrong, then the range
reduction of 64-bit to 32-bit values could generate a falsely in-range
value.
Instead, perform the computation in 64-bits, range check that value and
then assign to a 32-bit variable.
Signed-off-by: Keith Packard <keithp@keithp.com>
All the gpio drivers are based on devicetree and thus we always set
HAS_DTS_GPIO, thus we don't need this Kconfig option anymore. Remove
uses as its safe to assume DTS is supported for GPIO.
Signed-off-by: Kumar Gala <galak@kernel.org>
This patch adds DTS properties for using wake-up mode
and the autosleep function to the ADXL362 driver.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Adds few missing zephyr/ prefixes to leftover #include statements that
either got added recently or were using double quote format.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This sensor is virtually identical to the lsm6dso. The only difference
is the accelerometer ranges are double those of the lsm6dso.
Use the same driver. The difference is detected by using "st,lsm6dso32"
as the first compatible entry, followed by "st,lsm6dso".
An bit flag in the existing accel_range config field is used to check if
the chip is the doubled range or not.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
Move common settings out of the SPI and I2C instantiation macros and
into a common macro, which the aforementioned two macros can then use.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
In ST HAL v2.00, the functions to get the raw sensors values, e.g.
lsm6dso_acceleration_raw_get(), convert from little-endian to CPU.
Previous versions of ST HAL didn't do this.
The conversion here in the driver is converting a second time. It's not
an issue on a LE system, the conversion is a no-op, but on a BE system
it would be broken.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx tachometer driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Store sensor trigger structure reference provided on `trigger_set`, and
pass reference back to client when trigger callback is invoked.
This will enable client to use `CONTAINER_OF()` inside its trigger
callback code.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Comparator will monitor signal though ADC channel, based on
user configuration, callback will be triggered.
This will enable comparator functionality for nuvoton MCU utilizing its
ADC threshold detection feature. Implementation is exported through
sensor trigger API. Use of CONFIG_ADC_CMP_NPCX is required.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Currently the driver only setup the ADC to read from the
internal temperature channel on init. However, it is possible
that some other application that uses the ADC can setup the
ADC to read from some other channel and therefore subsequent
stm32_temp_sample_fetch will fail to read the targeted channel.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The ADC should be calibrated on init, there is no requirement
to calibrate ADC again on stm32_temp_init, remove it.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Consolidate the initialization routines and change the include guard to
conform with the coding guidelines as a preparation for the following
commits which add support for the SPI interface.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
This fixes the constant for the mem page and replaces a
magic number with the already defined `BME680_LEN_COEFF2` constant.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Add DT option to configure the data ready interrupt mode.
Latched is the default; pulsed can be enabled through
the drdy-pulsed DT, if desired.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add optional threshold interrupt support.
Implemented using SENSOR_TRIG_THRESHOLD sensor trigger type.
The features can be optionally enabled through Kconfig,
or disabled for smaller code size.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add FDS (Filtered Data Type Selection) + High-Pass reference mode support
(FDS in CTRL6, HP_REF_MODE in CTRL7)
Values are configurable through DT per instance.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
sensor_channel_get() API should return -ENOTSUP when requested channel
is not supported. This behavior allows to use `sensor get DEVNAME` shell
command easily, as all unsupported channels are filtered out.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Value changed from 100us to 150us. Value was not enough upon softreset.
This value was arbitrarily chosen and should be changed if more
information on the subject is provided.
Fixes#43794
Signed-off-by: Diogo Correia <dcorreia@protonmail.com>
