There does not seem to be a simple way to express the fact that UART1
can be initialized later at the POST_KERNEL level. The existing code
is wrong in the sense that it always initializes DT instance 1 later,
instead of doing it for UART1 (which may not be instance 1).
In addition, UART instances on other platforms are
also initialized at the PRE_KERNEL_1 level regardless of the instance
index, so let's do the same on this platform for consistency.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The power configuration is dependent on which UART is physically used.
In order to allow DT_INST_FOREACH_STATUS_OKAY() to iterate through
instances without the assumption that index 0 corresponds to UART0
(which would be incorrect in the case when only UART1 is enabled),
we need to check the base address to identify which UART is being dealt
with.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
When the loop that tries to obtain the lock in poll_out() finishes
because of hitting the max number of trials (what normally should
never happen), force the lock to be taken instead of just giving up
with sending the data. The latter approach that was in use so far
could not deal with a situation when some thread was aborted while
keeping the lock. Other threads would then have no chance to send
anything with poll_out() until it was called from an ISR.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When PCIe is enabled for UART, the port address is probed during
initialization and is written back into the device config struct.
However, the device config struct is supposed to be const and
read only. This results in page faults when MMU is enabled as
the struct cannot be written into. So fix this by storing port
address in device data struct if a particular UART instance is
of PCIE.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The init function returns successful even if the first
configuration function call fails. This may leave
a non-usable UART to be discoverable with
device_get_binding() which will definitely result
in lots of head scratching. So change the init function
to return properly.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The existing uart driver ns16550 did not have ISR locking that
effected IO APIC working in fixed delivery mode in SMP system
x86_64. This commit adds ISR locking mechanism using spinlock
for the interrupt related services.
The CONFIG_IPM_CONSOLE_STACK_SIZE is increased to lift
limitation of stack size experienced in IPM driver test with
this spinlock impelentation.
Fixes#23026
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add infineon XMC4 series UART support. Driver supports
only poll mode using XMCLib.
Out of 4 available UART's on SoC, only UART1 is confgired
by default in UART mode until GPIO & pinctrl support.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Swap this out and make the status a parameter.
Leave a couple of cases of DT_NODE_HAS_COMPAT().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
These are redundantly checking a node's status twice.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The conversion in 9b096f40b6 left out a
few tidbits that were not converted properly. Complete the conversion
properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert to using DT_INST_LABEL() in the dma driver and convert dma users
to use the DMA property macros to get the dma controller name. We make
the assumption in the drivers that there is a single DMA controller
instance.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changing more of DT_* prefixed macros that refer to instances to use
DT_INST macros in GPIO, I2C and UART drivers.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert the driver to use the new dt macros. As part of this change we
remove a bunch of defines that happened in dts_fixup.h that didn't
belong there. Some of these should be converted to devicetree
properties at some point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver was extended so that the tests/drivers/uart/uart_basic_api
test case now passes. The following modifications were made for the
following items of the test case:
* test_uart_configure
* test_uart_config_get
The driver was missing the support to re-configure the UART at run-time
as well as to obtain the current configuration at run-time via the
.configure and .config_get hooks provided within the UART driver API.
For the flow control setting, bit (mask) definitions were added for the
Modem Control Register. Both the configuration get and set functions
come with auxiliary functions that convert configuration register bit
masks to the UART driver API's enumeration types and vice versa.
For run-time configurability, the device's data struct is required un-
conditionally, previously, it was only available whenever interrupt-
driven mode was enabled. Consequently, the device initialization was
simplified to a single call of the DEVICE_AND_API_INIT macro, as the
existance of the device's data struct is now no longer conditional.
* test_uart_fifo_fill
For the user callback function of the test case to receive the initial
'Ready to TX' indication upon which the TX FIFO is filled, it is
necessary that uart_xlnx_ps_irq_tx_enable also sets the TX FIFO empty
bit in the Interrupt Enable Register. Consequently, the same modifi-
cation applies to the irq_tx_disable function.
* test_uart_fifo_read
During inital device configuration, the RX FIFO interrupt trigger
level has to be set to 1 byte for now, as the test case doesn't poll
the incoming data in a while()-loop, therefore, it misses the CR/LF
if more than one character is in the RX FIFO at the time of the
interrupt and neither CR nor LF is the first character.
Whenever the state of an interrupt is checked by the user callback
function (uart_xlnx_ps_irq_tx_ready, uart_xlnx_ps_irq_rx_ready),
the corresponding bits are cleared in the Interrupt Status Register,
re-enabling interrupts generated by the corresponding source.
Tested on QEMU (R5, A9) and actual Zynq7000 hardware.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Added the SERIAL_SUPPORT_INTERRUPT feature flag to the driver's
configuration file. This flag was missing, although the driver
supports interrupt-driven operation.
Interrupt support is required for testcases using the UART_PIPE
feature on the upcoming Cortex-A9 targets (QEMU/Zynq-7000).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Fix for the UART_XLNX_PS_IRQ_CONF_FUNC macro, which wraps IRQ_CONNECT
into a function for each device instance. This macro had device
instance #0 hardcoded at one point.
Interrupt support is required for test cases using the UART_PIPE
feature on the upcoming Cortex-A9 targets (QEMU/Zynq-7000).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
In some cases (eg at high baud rate, no HW flow control, and when BLE
radio/ints running) data could be lost between when enough characters
have been RX'd to fill the DMA buffer and when the ENDRX event was
fired, where the the STARTRX task is invoked to start filling the next
buffer (which is set up earlier, but I think will not be filled until
STARTRX).
To fix this, the SHORT is enabled between ENDRX and STARTRX whenever the
'next' buffer is available, so that STARTRX is invoked automatically and
subsequent chars go into the next buffer via EasyDMA.
To make this work properly, uarte_nrfx_isr_async() now handles the ENDRX
event _before_ the STARTRX event.
There was also an issue in rx_timeout() where the received character
count (rx_total_byte_count) could be incremented greater than the actual
buffer size. This arises from rx_total_byte_count value coming from the
counting the RXDRDY events (either by PPI/timer counter or counting the
RXDRDY ints themselves) and so if chars are received in the rx_timeout()
(or before ENDRX is handled) the rx_timeout() could increment rx_offset
past the length of the buffer. This could result the remaining 'len'
being calculated incorrectly (an underflow due to unsigned - signed ,
where signed > unsigned).
To fix this, we now store the lengths of the buffers and don't invoke
the UART_RX_RDY callback when the buffers are full; its handled by
ENDRX.
(Also note that the buffer size should be available via the RXD.MAXCNT
register on the nrf, but this register is not exposed through the nrfx
HAL and is also double buffered, so it seemed clearer to just track the
buffer lengths explicitly here in the driver).
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
for fixup
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
When we build this driver with CONFIG_UART_ASYNC_API enabled we get the
following build error:
uart_sam0.c: In function 'uart_sam0_init':
uart_sam0.c:558:35: error: redefinition of 'dev_data'
558 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
uart_sam0.c:498:35: note: previous definition of 'dev_data' was here
498 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
Fix this be removnig the duplicate at line 558.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Avoid entering an infinite loop when configuring the the NXP Kinetis
LPUART IRQ.
Fixes 9a65318a5b.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The UART driver for samd0 was is missing the .configure and
.config_get functionality expected from api for serial driver.
This commit fixes this by providing basic configuration
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>