Replace various drivers and soc code that use DT_CAVS_ICTL_BASE_ADDR
with DT_REG_ADDR(DT_NODELABEL(cavs0)).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The second paramater to IRQ_CONNECT for ipm_mhu_irq_config_func_0 should
be passing the priority, instead it passed the IRQ number. Fix this to
pass priority (which matches ipm_mhu_irq_config_func_1).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since idc_read/idc_write are used outside of the driver we can't use the
DT_INST_... form (that utilize DT_DRV_COMPAT) of the macro's in
ipm_cavs_idc_priv.h. Use DT_INST(0, intel_cavs_idc) explicitly in the
header to fix the build issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a rather primitive driver for use with the Intra-DSP
Communication (IDC) on the DSP on certain Intel SoCs. The IDC
generates interrupts from one core to another by writing to
certain registers. This is also being utilized as
the scheduler IPI since it can interrupt other cores.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Cleanup around COND_CODE_1 usage and replacing with
IF_ENABLED if applicable.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
event_index must be lower than NRFX_IPC_ID_MAX_VALUE.
As of now, maximum index is 16.
Fixes#20962, #20964, #20967
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
Remove the
# Omit prompt to signify a "hidden" option
comments that appear on some symbols. They seem to have been copy-pasted
at random, as there are lots of promptless symbols that don't have them
(that's confusing in itself, because it might give the idea that the
ones with comments are special in some way).
I suspect those comments wouldn't have helped me much if I didn't know
Kconfig either. There's a lot more Kconfig documentation now too, e.g.
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Keep some comments that give more information than the symbol having no
prompt.
Also do some minor drive-by cleanup.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These calls are not accessible in CI test, nor do they get built on
common platforms (in at least one case I found a typo which proved the
code was truly unused). These changes are blind, so live in a
separate commit. But the nature of the port is mechanical, all other
syscalls in the system work fine, and any errors should be easily
corrected.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move ipm.h to drivers/ipm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Some more were added since the cleanup pass in June 2018. See e.g.
commit 2d50da70a1 ("drivers: ipm: Kconfig: Remove redundant 'default n'
properties") for a motivation. It also avoids people wondering whether
or not they need to put in 'default n'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The header ipm_quark_se.h was creating a object. Hence removed it
and placed the same in ipm_quark_se.c
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add driver for i.MX Messaging Unit peripheral which can be used for
i.MX6SoloX, i.MX7D and other i.MX socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
irq_lock returns an unsigned int, though, several places was using
signed int. This commit fix this behaviour.
In order to avoid this error happens again, a coccinelle script was
added and can be used to check violations.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Refactor internals of IPM driver removing bitfields and byte access of
32 bit registers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The current method of accessing 32-bit data and control registers does
not work for all quark architectures. Sometimes writing to those
registers byte-by-byte results in last byte occupying whole 32 bit
register.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>