In some BLE use cases, using MSI driven SYSCLK is required.
Rework board Kconfig.defconfig in order to enable use of 2
alternate default clock configurations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Currently, it seems that only boards with smaller amount of RAM
get a value for "ram" property, and very few boards have "flash"
defined. However, to test bigger sample applications, it's helpful
to have these properties universally defined.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Let's point users at the latest documentation on flash
partitions from each of the board files, rather than duplicating some
of the information in it.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The hts221 sensor driver was implicitly made dependent upon the
disco_l475_iot1 board when it was converted to dts, so build the
associated sample only for this board. This issue was encountered when
adding sensor dts support to nxp boards, which don't have hts221.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We should enable CONFIG_POLL on application level when
we want to use SPI transceive_async() function.
This patch removes it from disco_l475_iot1 default
configuration.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Move bluetooth module SPI port related configuration
to dts and generate dts based defines on 96b_carbon
and disco_l475_iot1.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Adding 'config POLL' in Kconfig.defconfig creates a dependency
between CONFIG_POLL and board BOARD_DISCO_L475_IOT1 & SPI.
Remove this definition from the file and set CONFIG_POLL
in board _defconfig file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Defining TRIGGER_MODE choices in board Kconfig.defconfig files
brings unwanted dependency and warning messages when using sensors
on other boards.
Change sensor configuration by enabling wanted trigger choice rather
than redefining choice.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
ST official reference for this board is B-L475E-IOT01A.
While not used in zephyr, add reference in documentaion title.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
I2C_1 is enabled in board's DT file but we need to enable
it also in boards default config.
I2C_0 doesn't exist in STM32L475 SOC.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Provide default settings in disco_l475_iot board for following
sensors: LSM6DSL, LIS3MDL, LPS22HB, HTS221.
Sensors are disabled by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This requires openocd version 0.10 or later.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
Enable BlueNRJ chip on disco_l475_iot1 board.
Communication with SoC, is done over SPI(3). Hence this
commit enables SPI3 on SoC and configure BT_SPI IRQ,
RESET and CS pins.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board metadata to be consumed by the sanitycheck script to provide
better matching with testcases and to test based on features declated in
the board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Link was pointing to wrong reference manual.
Fixed by this commit
Change-Id: I97c6748fcad27ad6f2541ed4cba6141fcbb2576a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
I2C address could not be configured for HTS221.
Remove non existing configuration in disco_l475_iot1 board
Change-Id: Ib5ed8e0f770c16b124cf918bdf9ecd42cdd9b213
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
As disco_l475_iot1 is default board for HTS221 sample
application, provide default boards settings to get
application functional once it is delivered.
Change-Id: Ie4957538db679d076713550c1555954a6a20d3e2
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit provides support for disco_l475_iot1 board
Pinmux driver is provided with initial support definitions
Change-Id: I17b637a8ba0b033014969eca8fffe76319c47c52
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
