Delete the MAX44009 sensor sample as it's fully generic and does nothing
that's not already in light_polling sample.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
This platform was never supported in Renode, it's a leftover from Mi-V
support which probably was copied here. The referenced `it8xxx2_evb.repl`
does not exist in the Renode tree or in the `support` directory.
Signed-off-by: Patryk Koscik <pkoscik@antmicro.com>
Add memc driver for the MAX32 HyperBus peripheral, supporting HyperRAM
and Xccela PSRAM memory devices.
Signed-off-by: Pete Johanson <pete.johanson@analog.com>
Increase scan aux sets to support interleaved extended
advertising reception in hci_ipc ISO support configuration
in nRF5340 HCI ISO Controller.
CONFIG_BT_MAX_CONN is reduced accordingly as ticker node
instances are shared across all state/role scheduling in the
Controller implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Even though the STM32 TRNG hardware produces 2- or 4-byte sized words of
random data before triggering an interrupt, the driver currently discards
all but the bottom byte: 50/75% of the produced entropy goes to waste!
Make sure we consume all the random data from each word we read to improve
the entropy generation rate seen by users of the driver.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The BT Tester will not provide the opcode in the case of a
BTP error. To help log this for developers, we store the
opcode of the currently outstanding command, so that we can
log it.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
We now return "unknown" as the revision, and only concat onto
the revision if the revision is a valid git has value.
Signed-off-by: Andy Lee <andy@chiefmarley.com>
The Alternate Function IO (AFIO) block must have the clock enabled
before configuring. Some remappings seem to work without, but some
like EXTI do not. Fix.
Signed-off-by: Michael Hope <michaelh@juju.nz>
The PAN B511 evaluation board is a development tool for the
nRF54L15 from Nordic Semiconductor. Updates are based on latest
changes for nrf54l15dk.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Add test which is using two independent UART devices. Validate behavior of
asynchronous API.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add trigger_irq() function support for RX
This function will set corresponding IR bit to 1 on RX ICU to
trigger interrupt
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Add support for .mot file flash using west flash command
The RX build output .mot as binary file to flash into
board
Signed-off-by: Phi Tran <phi.tran.jg@bp.renesas.com>
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Intial support for RSKRX130 512KB board
The board 2 version 128KB and 512KB running on 2 different
part of the RX130 MCU series.
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Intial serial driver support for RX MCU, this driver utilize
the SCI HWIP for uart communication
Current support include polling API and Interrupt driven API,
some of the code is using Renesas RX Driver Package (RDP) as
hal layer
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Sang Tran <sang.tran.jc@renesas.com>
Initial commit for GPIO driver support on board using RX130 MCUs
* drivers: GPIO: implementation for GPIO driver on RSK_RX130_512KB
* dts: rx: add device node for GPIO of RSK_RX130_512KB
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Phi Tran <phi.tran.jg@bp.renesas.com>
Intial support of pinctrl driver for Renesas RX MCU
family.
This support base on using Renesas RX driver package in
hal_renesas layer
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Phi Tran <phi.tran.jg@bp.renesas.com>
This commit add a system timer driver for Renesas RX using the
CMT peripheral. The driver supports both system ticks and
high-resolution cycle counting
- Configures CMT0 as the system tick timer
- Configures CMT1 as a free-running cycle timer for precise
time tracking
- Handles timer overflows to maintain a continuous cycle count.
- Implements sys_clock_cycle_get_32() and sys_clock_cycle_get_64()
for high-resolution timing
- Supports Zephyr tickless kernel mode by tracking elapsed cycles
- Enables interrupt-based tick announcement using CMT0
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Yuichi Nakada <yuichi.nakada.sx@renesas.com>
Initial support of clock control driver for RX MCU
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Signed-off-by: Tran Van Quy <quy.tran.pz@renesas.com>
The qemu-system-rx is based on RX62N, this commit added
support for the RX62N SOC layer. MCU is using RXv1 core and
system timer running at 6MHz
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Add intial support for RX linker script
The RX GCC toolchain automatically adding an "_" as prefix
on every C symbol to comply to the arch ABI, for the C file
to understand the symbol define in linker script the
PLACE_SYMBOL_HERE() macro help to add "_" to linker script
define symbol if build with CONFIG_RX enable
This commit adding minimal support in common linker script
for RX arch
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The Renesas RX support flashing .mot file for binary image
This commit target to add the .mot file output for build and
flash script
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Current clock synchronization was always stepping clock. This was
causing large offset, and discontiguous ptp hardware clock time.
For TSN hardware, discontiguous ptp hardware clock time was not
able to be used for other TSN protocols.
This patch is to convert to frequency adjustment with a basic
PI control algorithm.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
