Since the test is hardcoded to prioritize testing a spi nor flash if
there is one, add a twister case for disabling that config in case if a
platform should also test some other flash which is present, such as
internal SOC flash. I.e, relevant platforms would be those which have
both internal and spi nor flash enabled in DT.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The Sparkfun Teensy Micromod was designed by Paul of PJRC
and manufactured and sold by Sparkfun.com
The functionality of this board is very similar to the Teensy 4.
It has the same basic pin definitions of the Teensy 4 but added
6 additional IO pins. Which added a lot of possibilities to use
the flexio system in new ways, such as for camera input.
It was unclear if the board should be added here or all of this
duplicated under Sparkfun, but now Sparkfun is also now responsible for
the manufacturing and sales of the Teensy 4 and Teensy 4.1, here feels
like a good place.
Note: I am mainly doing this as a learning experience on how to use
zephyr directly, as most of my experiences with Zephyr is done through
the current WIP Arduino Wrappers for some of their boards.
So far I duplicated the Teensy 4.1 files, then modified, like removed
the Ethernet and added the I2C2 object.
I updated the flash information as these come with a 128mbit version
versus the 64 on T4.1 or 16 on T4.
So far I have only test blink.
plus: cdc-acm example, plus adding gpio to it,
plus logging, plus blinking.
Signed-off-by: Kurt Eckhardt <kurte@rockisland.com>
This header uses enum mcumgr_err_t but does not include the
header where it is defined. Fixed in this commit.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
There appears to be a typo in the arduino header .dtsi
compared to UM2592 and physical hardware.
Signed-off-by: John Bason Mitchell <johnbasonmitchell@gmail.com>
Replace the assert on the value of the prescaler by a standard check and
an error value return (similar to the STM32 XSPI PSRAM driver).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
For STM32 XSPI PSRAM driver, compute and set the prescaler automatically
according to the kernel clock and the max frequency of the PSRAM.
Copied from what is done in the STM32 XSPI Flash driver.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add a parameter to define the maximum PSRAM frequency for the STM32 XSPI
driver. It will be useful to automatically calculate a prescaler.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
With BT_SETTINGS enabled, there doesn't seem to (anymore?) be any
substantial overhead in stack consumption:
0x200020b8 BT RX WQ
options: 0x0, priority: -8 timeout: -9223372036854775808
state: pending, entry: 0x5ba69
stack size 2240, unused 1072, usage 1168 / 2240 (52 %)
Let's just remove the conditional default and fall back to the
non-conditional one which is 1200.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Add buttons connected via GPIOs 0 to 3 for the NEORV32 MinimalBoot and
UP5Kdemo board variants.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Calibration process can be simplified if LF clock is always on.
Kconfig was depending on RTC being used as system clock because
that indicates LF clock being always on. Same can be done for
case when GRTC is used as system clock.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
mpfs_icicle timeouts on this test similarly to other boards
simulated in Renode. Null pointer dereference doesn't trigger
a CPU fault during simulation. Instead, call k_panic() directly.
Link: a28d5df5c6
Signed-off-by: Marek Slowinski <mslowinski@antmicro.com>
The Kconfig help text for the SN74HC595 driver refers to the device
as a "GPIO extender", which is inconsistent with the devicetree
binding file (ti,sn74hc595.yaml) that describes it as a "GPIO expander".
Signed-off-by: Hank Wang <wanghanchi2000@gmail.com>
Make sure iso_interval_us is in a multiple of 1.25 ms instead of directly
assigning it the value of SDU interval
Fixes EBQ failures in LL/CIS/CEN/BV-36-C and LL/CIS/CEN/BV-37-C
Signed-off-by: Troels Nilsson <trnn@demant.com>
Set the loopback interface name to "lo" instead of using the
default "dummy0" as the former is a more appropriate.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
According to TCP Spec. RFC793, ACK flag should be always set
after sequences of both sides are sync-ed except for RST seg-
ment. It is not necessary to send FIN only packet in the
test case, using FIN | ACK instead.
Similarly, change the tcp_out(conn, FIN | ACK) in CLOSE_WAIT.
Signed-off-by: Shrek Wang <inet_eman@outlook.com>
Port the nordicsemi_nrf53_init to use soc_early_init_hook instead of
SYS_INIT as SYS_INIT is legacy.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Expand the CAP broadcast reception test to also run with
multiple acceptors to better verify correctness in the
procedures.
For this to run more stable, the maximum number of streams
has been reduce to 2, rather than
CONFIG_BT_BAP_BROADCAST_SRC_STREAM_COUNT.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
In uuid.h the function uuid_generate_v5 had a 'namespace'
parameter which is a reserved C++ keywork.
Renamed to 'ns'.
Signed-off-by: Daniel Nicoletti <dantti12@gmail.com>
Change PWM to use buffers registers instead of writing period
and compare directly. This addressses an issue when updating
period to a value less than current counter, as demonstrated
in the blinky_pwm sample running on the CYW920829M2EVK_02
board.
Signed-off-by: John Batch <john.batch@infineon.com>
This commit fixes a type in kernel/driver/index.rst,
present in the "Drivers that do not use Zephyr Device
Model" subsection
Signed-off-by: Dhruv Menon <dhruvmenon1104@gmail.com>
As the code noted, the RGMII RX and TX clock delay values may need to
change depending on the MAC configuration or the PCB layout. Add
properties to allow configuring these in the device tree, defaulting to
the previous hard-coded values if not present.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
pm_state_get() is used to get a PM state that can be forced.
Disabled states (not included in automatic state selection) can
also be forced thus they should be included in search inside
pm_state_get().
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The GPTM is a general purpose module with a 16 bit prescaler, 16 bit
counter, and 4 compare units that can be used for PWM generation.
Use the same style as gd32 where the timer is a counter and the PWM
mode is a child node.
Signed-off-by: Michael Hope <michaelh@juju.nz>
when following the example it was not clear that BUILD_DIR needs to point
to application for sysbuild builds
Signed-off-by: Tobias Meyer <tobiuhg@gmail.com>
`pyocd` fails the second time the MCU is flashed.
Add `pyocd` flags identical to other nucleo boards to fix the issue.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Currently the driver code does not actually request the flow control
state, it only checks if the state exists. To fix this we should
simply call pinctrl_apply_state() and if that fails, meaning no
flow control state exists, fall back to default pin mux settings.
Another case that needed fixing is run time flow control enabling
ie in the case where we have a WIFI/bluetooth module connected
and we initially operate without flow control but later enable
it after firmware download.
This patch addresses this as well by making a generic function
to achieve this.
Signed-off-by: Bas van Loon <bas@arch-embedded.com>
