When building with monolithic feature enabled, the firmwares binaries
will be linked during the build with the application. This means we can
remove the application size limit due to the firmware storage in flash
not useful anymore.
Signed-off-by: Axel Le Bourhis <axel.lebourhis@nxp.com>
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
Added MAX32680EVKit board
For more information about this board please check
https://www.analog.com/
Co-authored-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
- The MK22FN512VLH12 chip, installed on frdm_k22f,
has 512 KB of Program Flash and 128KB SRAM
according to the K22P121M120SF7RM.pdf manual (page 55).
- Fix the flash size to 512KB (was 1MB).
- Add nxp_k22fn512.dtsi with correct flash size value.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Set the radio status as ok as the SOC/CPU DT include
does not do it for us.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
As now we have a sufficient model of the CLOCK peripheral,
let's mention it in the docs, and correct the warning
about not supporting the BLE stack.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Added MAX32655FTHR boards.
For more information about this board please check
https://www.analog.com/MAX32655FTHR
Co-authored-by: Maureen Helm <maureen.helm@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Added MAX32655EVKit boards.
For more information about this board please check
https://www.analog.com/
Co-authored-by: Kevin Townsend <kevin.townsend@analog.com>
Co-authored-by: Maureen Helm <maureen.helm@analog.com>
Co-authored-by: Okan Sahin <okan.sahin@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add more specific compatible strings to existing atmel,at24 compatible I2C
EEPROMs where known. This is strictly for documentation purposes, no
functional changes introduced.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds definition of ACE 3.0 Panther Lake board.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This commit adds support for the SPI which
can be found in Apollo3 SoCs, it can work in
both DMA and non-DMA modes
Signed-off-by: Hao Luo <hluo@ambiq.com>
Add ADC prescaler values in the RCC nodes to check that compilation with
these properties works. The values set in the dts are the default values
of the registers.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Re-enable enet on mimxrt1020 board using the new devicetree.
Build and execution of zperf sample on this board is successful.
Signed-off-by: Adam Matus <adam.matus@nxp.com>
This patch enables the user to control the RGB LED on the Arduino Nicla
Sense ME board. The RGB LED is controlled by the IS31FL3194 LED driver
and is connected to the I2C0 bus.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
This commit introduces support for an alternate linking method in the
LLEXT subsystem, called "SLID" (short for Symbol Link Identifier),
enabled by the CONFIG_LLEXT_EXPORT_BUILTINS_BY_SLID Kconfig option.
SLID-based linking uses a unique identifier (integer) to identify
exported symbols, instead of using the symbol name as done currently.
This approach provides several benefits:
* linking is faster because the comparison operation to determine
whether we found the correct symbol in the export table is now an
integer compare, instead of a string compare
* binary size is reduced as symbol names can be dropped from the binary
* confidentiality is improved as a side-effect, as symbol names are no
longer present in the binary
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Provide a replacement for CMSIS' NVIC_GetEnableIRQ()
as some applications use it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The VMURT1170 board configures the FLEXSPI to run at 200MHz serial clock
in DDR mode, via the flash configuration block passed to the ROM API.
Per the datasheet of the MX25UM51345G flash present on the board, 20
dummy cycles are required before reading data in OPI DTR mode. Correct
the dummy cycle value used for read commands to 0x28 (40 DDR dummy
cycles, equivalent to 20 dummy cycles of the clock) to resolve this
issue.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for Nuvoton numaker board numaker_m2l31ki.
m2l31x has 4 MPU regions and can't afford one more region
for USERSPACE, so set CONFIG_USERSPACE=n in m2l31ki_defconfig.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
This is a soc/board integration for the MediaTek Audio DSP device on
the MT8195 SOC, along with a Zephyr mtk_adsp soc integration that will
work to support similar 8186 and 8188 device shortly.
A python loader (similar to cavsload.py) is included that will run in
developer mode on current chromebooks (an HP x360 13b-ca000 was
tested) with an unmodified kernel.
Signed-off-by: Andy Ross <andyross@google.com>
Add a shield for DVP FPC 24-pins mt9m114 camera modules. These camera
modules are supported on i.MX RT10xx series, for example.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
The mt9m114 camera module is not always attached to this board. Camera
stuffs should go into a seperate overlay / shield. Also, the CSI should
be enabled only if there is a camera sensor attached to it.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
- Optimize slot sizes for MCUBoot swap move algorithm
for mimxrt1010/15/20/24/40/50/60/64 boards.
- Save up to 64 wasted sectors.
- Use DT_SIZE_K/M macros for slot sizes.
- Fix partition size errors.
- Limit mcuboot max size to 128KB (was 256KB).
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
The RA4M1 Clicker is a basic development board for the Renesas RA4M1
Microcontroller. The board contains J-Link on board, two LEDs and push
buttons and several headers for interfacing with external devices.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
This PR corrects the base addresses and region names of some memories
present in the MPS3-AN547 hardware.
Fixes#71920
Signed-off-by: Manuel Loew <manuel.loew.infineon@gmail.com>
Add DMA channels at SOC level for the LPC55S6x series SOCs, as the dma
requests are SOC specific properties and do not need to be modified at
the board level. Remove any DMA request definitions present at the board
level for the LPC55S69 evaluation board.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Declare a sub-region of the whole ext_memory with attributes
ATTR_MPU_IO so that XiP becomes possible on this external
octo- NOR flash. Use the STM32CubeProgrammer runner
with the external loader for flashing.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Declare a sub-region of the whole ext_memory with attributes
ATTR_MPU_IO so that XiP becomes possible on this external
octo- NOR flash. Use the STM32CubeProgrammer runner
with the external loader for flashing.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Update dts to use ST7735R via MIPI DBI API.
Also, remove the reset-gpios, as on this board the LCD RESET pin is
directly connected to the system reset. And add LCD backlight pin
connected to PE10.
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
Mention that we have the RADIO peripheral,
but no encryption accelerators yet.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The RADIO models now contain the radio,
let's stop removing it, but as they do not support DFE,
let's disable DFE.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit should deal with optimizing device's
operation in terms of power consumption. In this
context:
1. Power and rail managers are enabled so that the
device can enter the sleep state and power
rails be set to the min. required levels.
2. Peripheral blocks should be enabled only when
there is need to do so.
3. Define the internal RCX oscillator as default
low power clock. RC32K should not be used as
it drifts significantly due to temperature and
voltage variations. Thus, affecting the whole
system stability regardless of its calibration.
4. PLL should be enabled only when requested and
on board level LP clock should be switched to
XTAL32K to avoid overhead due to RCX calibration.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
The driver isn't currently buildable due to "west blobs" support never
having been added for hal_telink. Furthermore, even if the blob
dependency is manually made available it turns out the code has
bitrotten to the point where it doesn't build anymore. This situation
has continued for several years without anyone taking action, so I think
it's safe to assume this is unmaintained and should be removed.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
The 'tfm' tag was removed from the samples in in
7c80473e0a but it remained in use in other
parts of the project.
This change brings back consistency through out the project.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
- Set MCUBoot "upgrade only" method,
as the program size is 128B (>32B).
- Set slot sizes to the same value,
required by the MCUBoot "upgrade only" method.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
