If a transaction fails, the bus was not being returned to idle. This
increases power consumption, and can cause the following transaction to
be misinterpreted.
By issuing a STOP command on error, we can ensure that the bus returns
to idle correctly.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
When calling i2c_transfer(), the bus failes to enter the idle state when
performing a read, or an unacknowledged write. This increases power
consumption, and can cause the following transaction to be
misinterpreted.
This behaviour was observed on a SAML21 part. There appears to be a race
condition between the peripheral setting CLKHOLD, and the command being
correctly set up - so now we wait for the CLKHOLD field to be set before
issuing the STOP command, and this resolves this issue.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
This fixes both TX ready and completed uart
calls to meet valid condition.
Closes#41526Closes#41624
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Rework the transmit error handling in the NXP MCUX FlexCAN driver:
- Frame transmission must be automatically retried in case of lost
arbitration or missing acknowledge.
- Abort any pending TX frames when bus-off state is entered.
- Fail early in can_send() if in bus-off state.
Fixes: #19502
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for disabling automatic retransmission of CAN frames
(similar to CAN "one-shot" mode in the Linux kernel).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce Pin Function Controller for Renesas R-Car family.
This first implementation support to set a given pin as gpio
or peripheral (GPSR), to set a peripheral function to a
pin (IPSR), to set pull-up, pull-down (PUEN, PUD).
In addition this driver allows to set driving capabilies(DRVCTRL).
Pins are identified thanks to the per SoC binding for
pin definition which also contains pin alternate function
parameters.
Some pins can also have driving capabilities, some have bias
capabilities.
In order to find the correct bias and drive registers pfc_r8a77951.c
describes the different registers.
Each SoCs or package will need to define getters
for these registers: pfc_rcar_get_bias_regs() and
pfc_rcar_get_drive_regs().
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
1. Rename DT_COMPAT_ST_BBRAM_IT8XXX2 to COMAPT_ITE_IT8XXX2_BBRAM
2. The default configuration "$( )" should be a parentheses instead
of curly brackets. The BBRAM for it8xxx2 can be driven after
correcting.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
BBRAM content should be cleared when boot from cutoff. Compare magic
number to decide whether to clear entire BBRAM.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Refactors all of the on-chip flash drivers to use a shared driver class
initialization priority configuration, CONFIG_FLASH_INIT_PRIORITY, to
allow configuring flash drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers.
Driver-specific options for SPI-based flash drivers are left intact
because they need to be initialized at a different priority than on-chip
flash drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
This commit updates the ieee802154 driver to match the current feature
set of the nRF 802.15.4 radio driver for nRF53 SoCs.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Clear ADRDY before enabling ADC to ensure the subsequent
wait for ADRDY does not stop prematurely in case ADRDY
was already set.
The "ADC on-off control" sections of the following reference manuals
were consulted. That gives at least one instance per series affected
by this change, even if not every affected MCU is covered.
- RM0438 (STM32L552xx and STM32L562xx)
- RM0351 (STM32L47xxx, STM32L48xxx, STM32L49xxx and STM32L4Axxx)
- RM0434 (STM32WB55xx and STM32WB35xx)
- RM0454 (STM32G0x0)
- RM0440 (STM32G4 Series)
- RM0399 (STM32H745/755 and STM32H747/757)
- RM0433 (STM32H742, STM32H743/753 and STM32H750)
- RM0453 (STM32WL5x)
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Use a wrapper for LL_ADC_Enable that also waits for ADRDY if required
by the SoC to make sure it's properly enabled everywhere this is done.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
the stm32 spi drivers now takes the DTS frame_format property
from the include/ drivers/spi.h
It will be possible to select the Motorola (default)
or TI from the DTS entry of the device,
when soc supports it, else a run time error is raised.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add kscan0 to support tests/driver/kscan/kscan_api.
When running the tests code on it8xxx2_evb, it shows fatal
error: IRQ is enabled. We find that once polling_task() is
created and executed, the KSI interrupt will be enabled and
before we call irq_connect_dynamic(), so we switch both
function sequence.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Add a dummy driver for the `vnd,adc` compatible to allow compilation of
drivers utilising an ADC when running "build_all" tests.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
On some platforms, HPET is not wired to trigger IRQ 2.
This would make HPET non-functional if the legacy
interrupt routing bit is set in the global config
register. This adds a DTS flag so the driver won't
set the bit to enable legacy interrupt.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add an interrupt driven i2c driver for gd32 i2c peripheral.
The transmit and reception method refer from GD32 SoCs user manual.
Particularly, reception method choose the solution B.
There have some wait for state ready logic in the driver. It cause by
i2c device internal state change slower than i2c driver.
Signed-off-by: HaiLong Yang <cameledyang@pm.me>
We will soon need to do more boundary checking to test whether we are
reading secure or non-secure memory.
Refactor the boundary checking in preparation for this.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
GPIOTE channel was not freed when pin was reconfigured. This lead to
channel pool draining when pin was frequently reconfigured.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This PR adds the different handling of temperature sensor for the
STM32L5 soc. In this soc, there are some calibration settings which
need to be applied for temperature conversion.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
moving the conversion from adc value to the get function
which will be used for different handling of stm32 temp sensors
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
Just minor styling changes to capitalize the first character
and removing the trailing comma on the brief doc description
on two copy functions.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add optional user data argument to can_set_state_change_callback() to
comply with Zephyr API design guidelines.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Subghzspi instances cannot have any pinctrl configs,
they are blacklisted by the dts binding. This caused an
initialization failure of the spi_ll_stm32 driver for
subghzspi instance because no "default" pinctrl was found.
This commit solves the problem by skipping the pinctrl setup
for subghzpi devices. The use_subghzpi_nss property is used
to identify a subghzspi device, as this is a required boolean
property only available in the subghzspi binding this is a
perfect indicator for such instances.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
This commit adds the API of get_config that will make test of
tests/drivers/i2c/i2c_api pass on it8xxx2_evb board.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Certain stm32 soc's have a single shared irq for all adc channels
on those soc's only a single channel is supported.
Added a Kconfig that enables a shared irq for stm32f2x, stm32f4x,
stm32f7x soc's. The shared IRQ uses a flag to limit the number of
interrupts defined to only 1. A shared irq handler is added which
determines which ADC instance the interrupt is for, it then calls
into the existing interrupt.
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
The gd32_exti_isr function may be unused if the GPIO driver is not
enabled but EXTI is (no IRQ will connect to it). This may be improved in
the future by requiring explicit enablement of the exti DT node.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The default I2C channel 3 is used by alternate function of GPIO H1/H2
Krabby uses GPIO F2/F3 as I2C channel 3, so we need to add the
compatibility of the GPIO F2/F3.
TEST=test on it8xxx2_evb:
zmake configure -b zephyr/projects/it8xxx2_evb/
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Adding these definitions help ease of porting POSIX applications.
They currently do nothing in the core network stack and will
return an error if used. However, they help port some POSIX
without changing these. In particular, this enables using the
Nim programming language's standard library with Zephyr.
- The values copy Linux amd64, similar to the other SO_OPTIONS
- Add SO_SNDBUF to fix simplelink wifi
- Use compat options in simplelink wifi
Signed-off-by: Jaremy J. Creechley <jaremy.creechley@panthalassa.com>
