-Enable the die-temp capabilities of ADC in each dts file of stm32
boards where it is available.
-Execute the testcase running the samples/sensor/stm32_temp_sensor on each
available target board.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
Convert lptim configuration from Kconfig to device tree.
Note that some boards were using Kconfig default value (LSI),
which now has to be made explicit using device tree.
If not done already, enable the required clock node (lse/lsi).
Clean up related Kconfig bits when required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Set accel0 alias for all boards with the LSM6DSL accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add alias to boards with spi-flash to facilitate the
update of samples/drivers/spi_flash.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Add alias to boards with watchdog enabled to facilitate the
move of samples/drivers/watchdog to use DT_ALIAS.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
The goal of this commit is to update existing STM32 boards descriptions
to use these size "DT_SIZE" macros to enhance readability. To realize this
i used a python script, which will detect the STM32 Boards
/zephyr/board/arm, and then will update in the dts files the partition
description using "DT_SIZE_K" and "DT_SIZE_M" macros.
Check manually and modify in .overlay files in samples and tests.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
Add the pinctrl state name (default) for the PWM peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the CAN peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the I2C peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the ADC peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the UART/USART/LPUART
peripherals. Changes performed using the following Python script run
from the repository root:
```
from pathlib import Path
import re
for fpath in Path(".").glob("boards/arm/**/*.dts"):
lines = open(fpath).readlines()
is_stm32 = False
for line in lines:
if "stm32" in line:
is_stm32 = True
break
if not is_stm32:
continue
with open(fpath, "w") as f:
for line in lines:
f.write(line)
m = re.match(r"(\s+)pinctrl-0.*us?art.*", line)
if m:
f.write(m.group(1) + "pinctrl-names = \"default\";\n")
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add zephyr_udc0 (USB device controller) nodelabel to
STM32 boards with usbotg_fs node to allow generic USB device
samples to be build.
Follow up on commit e4f894788a
("boards: add zephyr_udc0 nodelabel to all boards with USB support")
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The stm32l47r soc has a dma of type dma-v2, so the cells have
only 3 elements,. This adpat for the quadspi periph.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit enables soc-flash support in disco_l475_iot1
only for flash test. Using overlays, it adds soc-flash storage
partition and deletes qspi-flash storage parition for
flash test. Both flash test and spi_flash application
has been tested on disco_l475_iot1 platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit changes from upper case to lower case in
"reg = <0x000D8000 DT_SIZE_M(7)"
"reg = <0x00000000 0x000D8000>"
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Mass conversion of STM32 boards to dts based clock configuration has
left some minor whitespace issues. Fix these and some other whitespaces
in the affected files.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
These were missing but not visible since value was defaulted
in Kconfig.
With Kconfig deprecation this breaks compilation.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure QSPI NOR support and MX25R6435F on disco_l475_iot1 board.
Set MX25R6435F as flash controller and arrange partitions to take
newlay available space into account.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update PWM pinctrl signal names of all non-F1 STM32 boards.
`pwm` variant is not available anymore on non-F1 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
In the flash partition definitions for ARM boards,
the link to the legacy partition macros does not
exist any more. The commit cleans up the partition
definition by removing this link.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
As a proof of concept, turn USB signals configuration to USB
for nucleo_wb5rg and disco_l475_iot1 boards.
This implicitly remove pull-up on _ID pin, which turn out to
have no side effect.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move SPI pin configuration to device tree for all STM32 based
boards.
This should not bring any change in pin configuration.
Though, some adjuments have been made on following boards for
coherency:
* b_l4s5i_iot01a1: Removed "very-high-speed" on SPI3 MOSI pin.
Tested with no impact.
* black_f407zg_pro: SPI1 pins configured but not SPI1 node.
Removed pin config as not documented neither.
* sensortile_box: SPI2 pins configured but not SPI2 node.
Removed pin config as not documented neither.
* nucleo_g431rb/nucleo_g474re/nucleo_l476rg/nucleo_l4r5zi:
SPI2 and SPI3 pins were configured but missing.
Added since they were documented.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new DT facilities to configure ADC pinmux on all boards with
STM32 MCUs currently supporting the ADC.
Signed-off-by: Martin Jäger <martin@libre.solar>
Use the new DT facilities to configure PWM pinmux on
DISCO-L475VG-IOT01A board.
NOTE: pinctrl file pointed to a wrong variant l475r(c-e-g)tx, however,
the SoC in the board corresponds to l475v(c-e-g)tx.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Adds the chip select devicetree flags to the spi_cs_control instance.
ISM43362 chip select is ACTIVE_LOW.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Fixes#26413.
The devicetree for disco_l475_iot1 declares the flash partitions
"storage" and "image-scratch" with overlapping address spaces.
As a result, when one of these partitions is used it can corrupt the
contents of the other one. This is the case when mcuboot performs an
image swap using the scratch partition.
To fix the bug, the size of the scratch partition is reduced.
Signed-off-by: Hans Wilmers <hans@wilmers.no>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
