Remove DW and PCA9685 PWM controller drivers as they are unmaintained
and broken.
Both drivers lack support for the pwm_get_cycles_per_sec_t API function
which was introduced in commit 56e0b53c6e
in 2016.
Fixes#18607, #18608
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Disable RTC WDT enabled (by default) by 2nd stage bootloader in ESP-IDF.
This WDT timer ensures correct hand-over and startup sequence from
bootloader to application.
Enabling bootloader caused system clock initialization to fail
when clock rate is greater then 80MHz. This also fixes
esp32 clock source code.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Extend the PWM API with optional API functions for capturing PWM pulse
width and period cycles.
Fixes#26026.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32L0 series MCUs have quite basic timer features only, so we
remove some unavailable configuration options. They were properly
initilized by the LL StructInit functions for other MCUs anyway.
Signed-off-by: Martin Jäger <martin@libre.solar>
So far nRF's TIMER was used for generating PWM signal. Add support for
generating PWM based on RTC, which is sourced by 32KHz low frequency
crystal. This allows to use low frequency PWM with much lower power
consumption, because high frequency clock path can be disabled.
Don't support RTC clock prescaler, because maximum 512s period covers
most use cases. This allows to adjust pulse and period cycles to the
fact that CLEAR task event is generated always one LFCLK cycle after
period COMPARE value is reached.
Also update hal_nordic revision, as it contains updated check for PPI
channels conflict when RTC is used to generate PWM.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far 'timer-instance' DT property was the way to configure TIMER which
was used for generating PWM signal. Replace that by using 'generator'
phandle, so we get prepared for supporting RTC instances as PWM signal
generator.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is some kind of runtime clock scaling implemented when period
cycles exceed 16-bit value. This is broken, because configured PWM has
far higher frequency in that case. Replace that mechanism with simply
veryfying if requested PWM period does not exceed 16-bit value.
Suggested-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use Nordic HAL to configure GPIO output. This adds support for P1 GPIOs,
when pin numbers above 31 are used.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Convert pwm drivers to use new DT variants of the DEVICE APIs.
DEVICE_AND_API_INIT -> DEVICE_DT_DEFINE
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL replaces all DT_ prefix with NPCX_DT_ for all macros used
for providing npcx device information in soc_dt.h It avoided the
ambiguity with the DT_ prefix for system DT macros/defines.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Enable ARR preload so that period or pulse updates are taken
into account synchronously with update event
(at the end of a ongoing period)
And thus avoid undetermined intermediate pulse.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The parameters of the associated PWM timer were not being picked up
properly, as it was assumed that parent index is the same as the child
index. This is not necessarily true if other timer nodes are active and
not being used for PWM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Set stm32_dt_pinctrl_configure function as the unique entry point
to STM32 DT pinctrl management.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move pinctrl remap functions out of stm32f1 definition in order
to get it available to all series.
Allows use of more IS_ENABLED macros in calling drivers and make
code more readable.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to be in line with other DT_INST macros in zephyr code base,
swap the arguments order in following macro definitions:
*ST_STM32_DT_PINCTRL
*ST_STM32_DT_INST_PINCTRL
Update the users accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Current set of helpers provided for STM32 pinctrl devicetree are
using device instance as input.
In order to prepare for next version that will take node identifier
as input, change existing set of macros using _INST_ namespace.
Additionally rename NODE_ID_FROM_PINCTRL to
ST_STM32_DT_INST_NODE_ID_FROM_PINCTRL.
Finally update existing macros users to this new name scheme.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that Zephyr names have been made short and nice the need of these
helpers is less justified.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
In npcx7 series, there're 8 Pulse Width Modulator (PWM) modules and each
one support generating a single 16-bit PWM output. A 16-bit clock
prescaler (PRSCn) and a 16-bit counter (CTRn) determine the cycle time,
the minimal possible pulse width, and the duty-cycle steps.
Beside introducing pwm driver for Nuvoton NPCX series, this CL also
includes:
1. Add PWM device tree declarations.
2. Zephyr PWM api implementation.
3. Add aliases in npcx7m6fb_evb board device tree file for supporting
samples/basic/blinky_pwm application and pwm test suites
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Replace all calls to the assert macro that comes from libc by calls to
__ASSERT_NO_MSG(). This is usefull as the former might be different
depending on the libc used and the later can be customized to reduce
flash footprint.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This runs the Timer/Counter for Control in 'normal' PWM mode. The
number of channels and counter width depends on the device and is
imported from DeviceTree.
Signed-off-by: Michael Hope <mlhx@google.com>
If shell is enabled then enable all sub-shells if their dependencies are
satisfied. This was done for some modules and subsystems but was not
consistent.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The PWM drivers has been refactored using the HAL LL API. Not only that,
but the set pin_set function is now faster, as channel output compare is
just initialized if needed.
NOTE: Has been tested using H743zi board for now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Allow configuring the clock prescaler divider for the NXP Kinetis
FlexTimer. Setting the prescaler to a lower value allows for much
higher resolution/accuracy for the generated PWM waveforms.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The driver-specific config_info structure referenced from the device
structure is marked const. Some drivers fail to preserve that
qualifier when casting the pointer to the driver-specific structure,
violating MISRA 11.8.
Changes produced by scripts/coccinelle/const_config_info.cocci.
Some changes proposed by the script are not included because they
reveal mutation of state through the const pointer, though the
code works as long as the driver-specific object is defined without
the const qualifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The TPM (Timer/PWM Module) is a 2- to 8-channel timer which supports
input capture, output compare, and the generation of PWM signals to
control electric motor and power management applications.
This patch adds the driver and the binding necessary for instantiating
the driver. The work is based on the RV32M1 driver for TPM done by
Henrik Brix Andersen. A later patch will enable this driver to be used
for the KW41Z SoC, if PWM support is requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
