The STM32_DMA_SLOT macro from include/drivers/dma/dma_stm32.h
must be used here, especially for dma of type v2bis.
In this case, the dma-cell is not defined and slot is null.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
add flow_ctrl filed and give it initialized value
based on hw_flow_control.
Initialize mcux lpuart based on flow_ctrl
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Microchip XEC has been using the standard NS16550 driver.
Using the standard NS16550 driver requires extra HW programming
for XEC UART in board level and did not support XEC GIRQ interrupt
programming. We add an XEC specific driver and remove UART specific
register programming from the board level and implement interrupt
support. Also, by implementing a SoC specific driver we can add
driver PM in the future.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
based on uart rom functions, also enable console driver
on top of this driver, which enables logging
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This is a follow-up to commit 3656ba5ae9.
Do not enforce pull-up resistors to be enabled on RXD and CTS pins
in nRF UART drivers, as in certain hardware designs this may be
undesirable or may even make certain hardware not working.
Instead, provide devicetree properties that allow enabling of those
resistors when it is actually needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of passing target states, use actions for device PM control.
Actions represent better the meaning of the callback argument.
Furthermore, they are more future proof as they can be suitable for
other PM actions that have no direct mapping to a state. If we compare
with Linux, we could have a multi-stage suspend/resume. Such scenario
would not have a good mapping when using target states.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Return -ENOTSUP if the requested state is not supported
- Remove redundant "noop style" functions.
- Use switch everywhere to handle requested state (not necessary in all
drivers, but better take off with consistency in place after current
changes).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The verb tense for the suspended state was not consistent with other
states. The likely reason: state was being used as a command/action.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The difference between low power and suspend states is a thin blur line
that is is not clear and most drivers have used indistinctly. This patch
converges to the usage of the suspend state for low power, since
contrary to the low power state, it is used by both system and runtime
device PM. The low power state is still kept, but its future is unclear
and needs some discussion.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM control function will only be called if the requested
state is different from the current one. A significant amount of drivers
were checking for state changes, now unnecessary. This patch removes all
this redundant logic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Since the state is no longer modified by the device PM callback, just
use the state value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is now invoked to set the device PM state in all cases, so
the usage of ctrl_command is redundant.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem already holds the device state, so there is no
need to keep duplicates inside the device. The pm_device_state_get has
been refactored to just return the device state. Note that this is still
not safe, but the same applied to the previous implementation. This
problem will be addressed later.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
based on uart rom functions, also enable console driver
on top if this driver enabling logging
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Add Atmel sam0 sercom[uart] pinctrl bindings and implements pinctrl at
driver level. It changes all sam0 boards to use new feature and remove
pinmux driver dependency for sercom[uart]. The samples that require a
binding were update to keep consistency and avoid errors.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The following device busy APIs:
- device_busy_set()
- device_busy_clear()
- device_busy_check()
- device_any_busy_check()
were used for device PM, so they have been moved to the pm subsystem.
This means they are now prefixed with `pm_` and are defined in
`pm/device.h`.
If device PM is not enabled dummy functions are now provided that do
nothing or return `-ENOSYS`, meaning that the functionality is not
available.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
All the macro for dma-cells are now in the
include/drivers/dma/dma_stm32.h header file.
So the include/dt-bindings/dma/stm32_dma.h is no more
useful and removed from #include.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The macro to set the element of the dma-cells for each peripheral
are defined in the dma_stm32 header file
and used in the periph driver (as dma client)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This is the dma V2bis which is particular DMA V2 instance for
stm32F1 and STM32L1 soc series. This DMA does not use the dma slot
Otherwise it is similar to version V2.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
When DMA switches from one buffer to another ENDRX followed by
RXSTARTED is generated. Code flow assumes that ENDRX will be
handled before RXSTARTED but this may not be the case if there
is a short between ENDRX and RXSTARTED and event occurs after
ENDRX event check but before RXSTARTED event check. In that case,
RXSTARTED event is handled first. Such case may happen if there
is a higher priority interrupt that may preempt UARTE interrupt
handler.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds a serial dummy driver compatible to vnd,serial.
This is needed that devices can access the uart device in tests
like tests/drivers/build_all/... .
Add myself as codeowner to avoid complicance check failure.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit add the support of "Interrupt driven UART"
to the R-Car UART driver and enable it in the related
Kconfig.
The driver is supporting nearly all the methods that are
described in the "Interrupt driven UART" part of the
uart_driver_api.
This new version of the driver has been tested on
H3ULCB board by running "uart_basic_api" test suite.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
The callback is not used anymore, so just delete it from the pm_control
callback signature.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
the device PM callback is not used anymore by the device PM subsystem,
so remove it from all drivers/tests using it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
hal_espressif repository was updated from esp-idf v4.2
to esp-idf v4.3 to allow latest Espressif chips integration.
As a consequence, it added a few changes in drivers
and peripherals. To maintain bisectability, changes in this
PR cannot be split. Here are some details:
wifi: update linker script by adding libphy and new attributes.
spi: update some APIs and fixed missing wait_idle check
west.yml: esp32: update hal to new version
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Move all PM_DEVICE_STATE_* definitions to an enum. The
PM_DEVICE_STATE_SET and PM_DEVICE_STATE_GET definitions have been kept
out of the enum since they do not represent any state. However, their
name has not been changed since they will be removed soon.
All drivers and tests have been adjusted accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
RXTO event is generated always after ENDRX and driver relies
on assumption that ENDRX event is handled before RXTO. However,
when interrupt is preempted after ENDRX check returned false
and RXTO event is already set handling order would be swapped.
Added addtional check to handle RXTO event only if ENDRX is not
set. If ENDRX is set, it means that it is not yet handled. RXTO
event is not cleared and interrupt will be triggered again and
ENDRX event will be handled first.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
UART CR_SIN interrupt enable/disable are invoked when CONFIG_PM enable.
This removes the guard for UART CR_SIN interrupt enable/disable to fix
the build issue.
Fixed#36520
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Convert the various device_get_binding() calls used to get the device
clock node to use DEVICE_DT_GET. The latter is processed at link time,
so it should be a bit more efficient.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
NPCX WIMU CR_SIN is used to wake up soc from NPCX sleep power state.
The wake-up IRQ enabled when UART init. It causes the wake-up IRQ to
generate many extra interrupt events, which causes the system too busy
to handle other events. This PR moves the UART wake-up IRQ enabling
from UART init to npcx_power_enter_system_sleep() to avoid the
interrupt storm.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Configured UART/UARTE input pins to have pullups. Otherwise when
uart is disconnected pins are floating and generate receiver
errors.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fix typo in configuration phase to prepare the driver
for incoming add of Interrupt driven uart mode.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
The macros are used to get the pin(s) of a given driver instance. Add
_INST prefix to match convention used by the devicetree.h. The original
macros can now be used to obtain pin(s) of an arbitrary device instance
identified by the nodelabel.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Since we removed various series headers, move stm32 driver
under main driver/pinmux folder.
Take this change into account into various drivers.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This kconfig option enables runtime configuration of UART
controllers. This allows application to call uart_configure()
to configure the UART controllers and calling uart_config_get()
to retrieve configuration. If this is disabled, UART controllers
rely on UART driver's initialization function to properly
configure the controller. The main use of this option is mainly
code size reduction.
Fixes#16231
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Currently zephyr has no means to control access to the uart
driver when it is inactive, e.g. shell is not aware of uart
being in idle state and calls asynchronous api. Add early
return to TX starting procedure if device is idle.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Make custom RTT locking configurable and select it where it is needed.
When using RTT for tracing we want to use the default locking.
Update both segger and tracerecorder modules to support that.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Function should return -ENOTSUP when asynchronous api is not
supported by the device.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Deadlock may occur when uart device was put to low power state
while uart_poll_out was in progress. Poll out pends until uarte
is ready to send new byte and it is detected by endtx and txstopped
events being set. When uarte was disabled while poll_out was pending
events were never set and that lead to deadlock. Added a step
in going to low power state in which CPU waits for txstopped event
and only after that uarte peripheral is disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When using the uart driver with interrupt and async api
at the same time (instance for interrupt and instance for async),
the transmission complete interrupt was handled in the async
handling section, even when interrupt driven api is used.
This caused transmission to not work properly in interrupt mode.
The fix is to move the interrupt mode handling to the begginning
of the isr. If async mode is used then interrupt mode code
will not be run.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
uarte_enable function was not supporting a case when async
api was enabled but instance did not use it. Added runtime
check for async instance presence.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
