The utility may be used during development stage to get
ambiq platform specific timing parameters for mspi devices.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
This device driver supports ISSI is25w/lx032/64 series flash.
Only extended SPI mode(1s-1s-1s, 1s-8s-8s, 1s-1s-8s) is implemented.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Adds a common vendor dts file specifying the default partition
layout for nRF54L05-based cpuapp board targets and updates boards
to use this common file. This also drops the secure/non-secure split
in the partitioning as this was reducing NVM storage that is not
used by this board target and fixes the wrong flash field in
twister yaml files
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds a common vendor dts file specifying the default partition
layout for nRF54L15-based cpuapp_ns board targets and updates boards
to use this common file.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds a common vendor dts file specifying the default partition
layout for nRF54L15-based cpuapp board targets and updates boards
to use this common file. This also drops the secure/non-secure split
in the partitioning as this was reducing NVM storage that is not
used by this board target and fixes the wrong flash field in
twister yaml files
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds a workaround for partitions on nrf54l10 non-secure devices to
prevent build issues, this needs to be fixed properly when a TF-M
update is done which sets the partition sizes properly
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds a common vendor dts file specifying the default partition
layout for nRF54L10-based cpuapp board targets and updates boards
to use this common file. This also drops the secure/non-secure split
in the partitioning as this was reducing NVM storage that is not
used by this board target and fixes the wrong flash field in
twister yaml files
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
jlink runner works fine for the Pico2, just like Pico1 (rpi_pico).
Copied relevant lines from rpi_pico/board.cmake.
Fixed typo in documentation.
Signed-off-by: Koen Van Herck <koen.v.herck@gmail.com>
Add gpio support for STM32MP257F-EV1 board.
Add the orange (&led0) LED to the device tree and enable GPIOJ.
Add the user button USER2 to the device tree and enable GPIOG.
This step allows building and debugging the blinky and button sample
applications.
Signed-off-by: Youssef Zini <youssef.zini@savoirfairelinux.com>
Introduce DeviceTree binding for the STM32MP2 RCC clock controller,
enabling support for STM32MP2-specific clock configuration in Zephyr.
Update Kconfig.stm32 to add a dependency on STM32MP2 configuration,
allowing the use of STM32 LL RCC features when targeting STM32MP2
devices.
Add header for STM32MP2 per peripheral clock definitions.
Signed-off-by: Youssef Zini <youssef.zini@savoirfairelinux.com>
Introduce initial board support for the STM32MP257F-EV1. This includes:
- Board metadata (board.yml, stm32mp257f_ev1.yaml)
- Base software configuration (Kconfig.stm32mp257f_ev1)
- CMake build integration (board.cmake)
- Default configuration (stm32mp257f_ev1_stm32mp257fxx_m33_defconfig)
- Minimal device tree (stm32mp257f_ev1_stm32mp257fxx_m33.dts)
- Initial documentation and image for the stm32mp257f_ev1 board.
- OpenOCD configuration files for debugging support.
This enables the STM32MP257F-EV1 board to build and debug a hello world
sample.
Note that other necessary openocd configuration files are added to the
zephyr sdk directory and can be found in the stm-openocd repository[1].
[1]:https://github.com/STMicroelectronics/device-stm-openocd/tree/main
Signed-off-by: Youssef Zini <youssef.zini@savoirfairelinux.com>
Update board document to remove dcache off command under U-Boot as
CONFIG_ARM64_BOOT_DISABLE_DCACHE has been enabled.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add external HSPI flash on STM32U5G9J-DK2
Use external loader to flash it with STM32CubeProgrammer
Signed-off-by: Mathias Markussen <mathias.markussen@st.com>
This adds `tests/drivers/dma/chan_blen_transfer` and
`tests/drivers/dma/loop_transfer` as build tests to any manual Twister
run.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Sets LinkServer as the default runner for the mimxrt1060-evk board,
as the board is configured for CMSIS-DAP by default.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Add minimal support for Renesas RZ/V2N-EVK
Signed-off-by: Hieu Nguyen <hieu.nguyen.ym@bp.renesas.com>
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Add documentation for am243x_evm and while at it, add the openocd
configuration as well.
Co-authored-by: Mika Braunschweig <mika.braunschweig@siemens.com>
Signed-off-by: Amneesh Singh <a-singh7@ti.com>
Added support for deriving `SYS_CLOCK_HW_CYCLES_PER_SEC` from the
Device Tree by reading the `clock-frequency` property in the `itim` node.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
The DTS for this board contained a few mistakes:
* The PHY address was incorrect
* This did not impair functionality because the RTL8211F
treats address 0 as "broadcast" and accepts commands
sent to it by default
* An incorrect PHY driver was used
* The generic "phy_mii" driver is not the most appropriate
for this PHY - use the HW-specific RTL8211F driver instead
* Also remove the PHY IRQ pin configuration from Ethernet
pinctrl to allow RTL8211F driver to receive IRQ via GPIO
instead
* The RGMII GTX CLK pinctrl must be configured at "medium-speed"
* This is a temporary solution. The proper solution would use
very-high-speed combined with a GPIO delay, but delays are
not supported yet in Zephyr.
Signed-off-by: Mathieu CHOPLAIN <mathieu.choplain@st.com>
Microchip is adding more non-MEC devices to Zephyr such as
SAM and PIC32. Each device family will have its own subfolder.
We moved the existing MEC DTSI files into a new mec subfolder.
We also updated the existing MEC boards include paths.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Call entropy APIs to use TRNG peripheral on STM32WB0x devices for BLE
purposes.
Enable RNG node on Nucleo-WB0x boards.
Remove RNG initialization as it's done in the entropy driver.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Specify the Arduino serial node for a Discovery kit with STM32H573II MCU.
Add supported features to board yaml file.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add basic board definition of the u-blox EVK-IRIS-W1-rw612 board.
Adds maintainer info for u-blox boards.
Signed-off-by: Tarang Patel <tarang3399.patel@gmail.com>
