Update discharge current limit property to be aligned
with the most recent npm1300 datasheet.
This affects the discharge current measurement calculation,
which needs to be scaled accordingly.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add `zephyr,memory-region-flags` for supporting memory region flags
setting.
For example, when the below node is in the devicetree,
```
test_sram: sram@20010000 {
compatible = "zephyr,memory-region", "mmio-sram";
reg = < 0x20010000 0x1000 >;
zephyr,memory-region = "FOOBAR";
zephyr,memory-region-flags = "rw";
};
```
We get the following line in MEMORY section of linker script.
```
FOOBAR (rw) : ORIGIN = (0x20010000), LENGTH = (0x1000)
```
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
- Fixes mcxw71 CI errors caused by wrong place
of the 'flash' node in DTS.
- Fixes mcxw71 build errors for storage, flash
and mcuboot examples.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
The Pico SDK defines a default value for its XOSC multiplier. Reflect
this in the device tree binding so that it doesn't need to be repeated.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Rename rpi_pico_common.dtsi to rp2040_reset.h . This is more consistent
with the wider Zephyr source tree, and is foundation work ahead of
introducing the RP2350 SoC.
Add missing include guard. This shouldn't be required, but it is
consistent with other header files in the same directory.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Follow the wider directory convention of dts/<arch>/<vendor>/<family>.
This is foundation work ahead of introducing support for the RP2350.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
This commit is to enable Ethernet drivers support on Renesas RA
MCU, first target support is the Renesas RA8 series
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Add support for mdio driver for Renesas RA MCU series
This support utilize the r_ether_phy driver in hal renesas
to support mdio write and read function
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Add support for GPIO controller feature of AW9523B.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Add a definition of a STEMMA QT connector to which I2C
devices can be connected.
Since STEMMA-QT does not specify uses other than I2C,
this is just a formal definition.
(It may be helpful when using this connector as a GPIO,
which is not defined in STEMMA-QT)
Maybe in usual need to define i2c alias such like as,
```
stemma_qt_i2c: &i2c0 { }
```
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Add watchdog driver for npm2100 pmic.
This pmic has one timer that can be used for multiple functions,
including a watchdog that can reset or power-cycle connected devices.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add sensor driver for npm2100 pmic.
This pmic performs measurements of battery voltage, regulator voltage
and die temperature.
Configurable pmic attributes are also organized under this driver.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add regulator driver for npm2100 pmic.
This pmic has one boost and one ldo regulator.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Add mfd driver for the npm2100 pmic device.
The driver contains basic initialization routines,
and functionality not covered by other device driver APIs.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Added dppic0 node label, alongside the dppic to maintain backward
compatibility. The use of dppic0 is preferred.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Add support for Norik Systems Octopus IO-Board based on
Norik Systems Octopus SoM.
Supported features:
- LTE-M/NB-IoT
- GPS
- LED
- 3-axis accelerometer
- Battery charger
- Solar charger
- SPI NOR flash
- Nano SIM connector
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
Add support for setting the sample frequency via `attr_set` and the
output data rate from device tree source.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
IT8801 support GPIO alternate function switching.
Some GPIO pins can be switched as KSO or PWM function.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The IT8801 is an I/O expander that provides GPIO, PWM, Keyboard
functions via the I2C bus.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Rename "nxp,kinetis-adc12" compatible to "nxp,adc12" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Rename "nxp,kinetis-wdog32" compatible to "nxp,wdog32" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The DPPI and PPIB peripheral nodes must be enabled to allow the
CONFIG_HAS_HW_NRF_DPPIC to be set. This change is consistent with what
was done on nRF5340 and does not introduce any additional memory
overhead, because there is no Zephyr driver behind the nrf-dppic and
nrf-ppib bindings.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Allow configuring the clock prescaler divider for the NXP Kinetis
Timer/PWM Module (TPM). Setting the prescaler to a lower value
allows for higher resolution for the generated PWM waveforms.
This change is inspired from the pwm_mcux_ftm driver:
Link: https://github.com/zephyrproject-rtos/zephyr/pull/25396
Signed-off-by: Maximilian Werner <maximilian.werner96@gmail.com>
Apply nRF54H20 `min-residency-us` and `exit-latency-us` values for
existing power states.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
Add 128 MHz clock source and use it for uart00. Baudrate setting
must be adjusted based on uart clock source so without this
change there is wrong baudrate on uart00.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add DT definitions for the RAK3172 LoRaWAN module, based on
STM32WLE5.
Ref. https://docs.rakwireless.com/product-categories/wisduo/
rak3172-module/low-level-development/
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
These devices have an architecturally fixed 13 MHz clock device. But
thankfully you can put a default into a DTS binding so we don't have
to repeat it for all of them.
Signed-off-by: Andy Ross <andyross@google.com>
In order for the driver to be compliant with the timing sequence
diagrams presented in the reference manual, the MCU has to wait
for some additional period of time while setting both the rs and rw
lines.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
Express delay values in nanoseconds. Set the default delay time values
as specified in the HD44780 reference manual.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
Separate the current driver for the FPGA iCE40 into two different ones.
One implements only the SPI load mode, the other one only the GPIO
bitbang mode.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The GECKO_PIN() macro does not do anything except pass the
argument through unaltered. It only serves to make DeviceTree
files more verbose. It was inconsistently used, make the .dts
files consistent by never using it.
The DBUS pinctrl driver doesn't use the port or location macros
from the gpio_gecko.h header. The pin number macro is the only
other thing defined in this header. Stop including the header on
Series 2 based boards.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
